Nokia 8860 - Cell Phone - AMPS User manual

Last modified 15-Mar-99
8860 User Guide Draft
pre-release version 0.01

8860 UG version 0.01 3/15/99 1
Indicators and Icons
You have an active call.
The phone is waiting for you to enter a response.
The current profile you have selected for your phone is
6LOHQW .
Keyguard has been activated to help prevent any accidental
keypresses.
You have one or more voice messages waiting.
You have one or more unread text messages waiting.
Digital service is available.
Any characters you enter will be upper-case letters or numbers. Press
the # key to switch letter case.
Any characters you enter will be lower-case letters or numbers. Press
the # key to switch letter case.
This appears when you press and hold the # key when storing names.
Letters can not be entered when this appears, allowing quicker access
to numbers.
You are in “special character” mode; select a special character and
press
,QVHUW . (When entering letters, you can switch to this mode by
pressing the ∗key.)
The alarm clock is set.
You have a reminder in your calendar to do something (appears only
on Calendar display).
You have a reminder in your calendar that it’s someone’s birthday
(appears only on Calendar display).
You have a reminder in your calendar to call someone (appears only on
Calendar display).
You have a reminder in your calendar of a meeting (appears only on
Calendar display).

2
1. Safety At A Glance
Read these simple guidelines before using your phone. Failure to
comply with these guidelines may be dangerous or illegal.
For more detailed safety information, “Important Safety
Information” on page 91.
Road Safety Comes First
Don’t use a hand-held phone while driving; park the vehicle first.
Switch Off In Hospitals
Switch off your phone when near medical equipment. Follow any
regulations or rules in force.
Switch Off On Aircraft
Mobile phones can cause interference. Using them on aircraft is
illegal.
Switch Off When Refueling
Do not use the phone at a refueling point. Do not use near fuels or
chemicals.
Switch Off Near Blasting
Do not use the phone where blasting is in progress. Observe
restrictions, and follow any regulations or rules in force.
8860 UG version 0.01 3/15/99 3
SafetyAtAGlance
Interference
All mobile phones may get interference which could affect
performance.
Use Sensibly
Use only in the normal position(to ear). Avoid unnecessary contact
with the antenna when phone is on.
Qualified Service
Only qualified service personnel may install or repair cellular phone
equipment.
Accessories and Batteries
Use only approved accessories and batteries.
Do not connect incompatible products.
FCC/Industry Canada Notice
Your phone may cause TV or radio interference (e.g. when using a telephone
in close proximity to receiving equipment). The FCC/Industry Canada can
require you to stop using your telephone if such interference can not be
eliminated. If you require assistance, contact your local service facility.
This device complies with part 15 of the FCC rules. Operation is subject to the
condition that this device does not cause harmful interference.

4
Using this Guide
The wireless phone described in this guide is approved for use in TDMA/AMPS
networks.
A number of features included in this guide are called Network Services. They
arespecialservicesprovidedby wirelessserviceproviders.Before youcantake
advantage of any of these Network Services, you must subscribe to the
service(s) from your home service provider and obtain instructions for their
use.
Disclaimer
It’s possible that you may not be able to activate your phone on all wireless
systems. Please see your service provider for details.
8860 UG version 0.01 3/15/99 5
GettingConnected
2. Getting Connected
You’re battery should be charged before you activate your new phone. This
section will help familiarize you on how, and when, to charge your battery.
Attaching your battery
Simply place the battery in the grooves on the back of your phone. Then slide
the battery upward until it clicks.
Note: Use only those batteries approved by the phone manufacturer and
recharge your battery only with the chargers approved by the manufacturer.
See “Important Battery Information” on page 8.
Removing the battery
Note: Switch off the phone before removing the battery!

6
Press and hold the button at the top of the
battery.
Slide the battery toward the bottom of the
phone.
Lift the battery off the phone.
Charging your new
battery
Your phone can be used with either a rechargeable
Li-Ionor NiMHbattery.Note thatanew battery’sfull performanceis achieved
only after two or three complete charge and discharge cycles.
With your phone on or off, connect the
charger to a standard 120V AC outlet. Then
connect the lead from the charger to the
bottom of your phone or place it on a
charging stand.
When the battery begins charging, your
phone will beep once and the battery
strength indicator on the right side of the
display will scroll.
Note: If the battery is totally empty, it may take a few minutes before the
charging indication appears on the display.
If your phone displays1RWFKDUJLQJ, charging is suspended. Check that the
battery is not connected to a non-approved charging device. If the battery is
veryhotor cold,waitforawhile;chargingwillautomaticallyresume afterthe
battery is restored to its normal operating state. If charging still fails, contact
your dealer.
8860 UG version 0.01 3/15/99 7
GettingConnected
When is a good time to charge?
You can charge your battery anytime. If you have a NiMH battery, you should
allow it to completely discharge once in a while.
Whenyourphonebeepsonceanddisplays %DWWHU\ORZ,you onlyhaveacouple
of minutes of talk time remaining. The repetition rate of these battery-low
warningsdependontheremainingbatterycapacityandthebatterycondition.
These warnings are more frequent when you’re in a call.
Note: The phone will not give you the warning tone under certain conditions.
See “Warning tones” on page 81.
Once all the power has drained from yourbattery, you’ll hear three beeps with
the message 5HFKDUJHEDWWHU\ on your display. At this point, your phone will
switch itself off and you’ll need to recharge your battery.
When is charging complete?
When the charge indicators stop scrolling, your phone is considered
fully charged. However, a slight increase in charge may occur if your
phoneisleftconnectedtothecharger forawhile.Thisis called“trickle
charge.”
Charging times depend on the type of battery and charger used.
For approximate charging and operating times, see “Standby and Talk Times”
on page 85.
Can you make calls while charging?
Yes, you can. But your battery may not charge while a call is in progress.
Charging should resume once you end the call.
Discharging NiMH batteries
A NiMH battery lasts longer and performs better if you fully discharge it from
time to time. To discharge the battery, leave your phone switched onuntil the
battery is drained. The phone will display several messages that the battery is
low and that you need to recharge it; just ignore them. Do not attempt to
discharge the battery by any other means.

8
Important Battery Information
• Note that a new battery’s full performance is achieved only after two or
three complete charge and discharge cycles!
• The battery can be charged and discharged hundreds of times but it will
eventuallywearout.Whentheoperatingtime(talk timeandstandby time)
is noticeably shorter than normal, it is time to buy a new battery.
• Use only batteries approved by the phone manufacturerand recharge your
battery only with the chargers approved by the manufacturer. When a
charger isnotin use, disconnect itfromthepowersource.Do not leavethe
battery connected to a charger for longer than a week, since overcharging
may shorten its life. If left unused a fully charged battery will discharge
itself over time.
• (NiMHbatteriesonly)Forgoodoperationtimes,dischargethebatteryfrom
time to time by leaving your phone switched on until it turns itself off (or
by using the battery discharge facility of any approved accessory available
for your phone). Do not attempt to discharge the battery by any other
means.
• Temperature extremes will affect the ability of your battery to charge:
allow it to cool down or warm up first.
• Use the battery only for its intended purpose.
• Never use any charger or battery which is damaged or worn out.
• Donotshortcircuitthebattery.Accidentalshortcircuitingcan occurwhen
a metallic object (coin, clip, or pen) causes direct connection of the + and
- terminals of the battery (metal strips on the back of the battery), for
example when you carry a spare battery in your pocket or purse. Short
circuiting the terminals may damage the battery or the connecting object.
• Leaving the battery in hot or cold places, such as in a closed car in summer
or winter conditions, will reduce the capacity and lifetime of the battery.
Always try to keep the battery between 59º F and 77º F (15º C and 25º C).
A phone with a hot or cold battery may temporarily not work, even when
the battery is fully charged. NiMH batteries’ performance is particularly
8860 UG version 0.01 3/15/99 9
GettingConnected
limited in temperatures below 14º F (-10º C). Li-ion batteries’ performance
is particularly limited in temperatures below 32º F (0º C).
• Do not dispose of batteries in a fire!
• Batteries must be recycled or disposed of properly. Must not be disposed
of in municipal waste.

10
3. The Basics
You have purchased a powerful phone, with lots of features. Read this section
for some very basic information on how to use your phone.
A more comprehensive description of your phone is covered in “Features A to
Z” starting on page 21.
Switching the phone on and off
Press and hold the Pkey for two seconds to switch the phone on or off.
Switching off with the Pkey
Quickly press the Pkey (6ZLWFKRII will appear, highlighted) then press 2..
NORMAL POSITION: Hold the phone as you would any other telephone with
the antenna pointed up and over your shoulder.
TIPSONEFFICIENTOPERATION:Aswithanyotherradio
transmitting device, do not touch the antenna
unnecessarily when the phone is switched on. Contact
with the antenna affects call quality and may cause
the phone to operate at a higher power level than
otherwise needed.
WARNING! Do not switch on the phone when wireless
phone use is prohibited or when it may cause
interference or danger.
See “Safety At A Glance” on page 2 for more information.
8860 UG version 0.01 3/15/99 11
The Basics
Get a good signal
Your phone operates on radio waves, and the quality of radio reception
depends entirely on the strength of the radio signal in your area.
This radio coverage is maintained by a wireless network and the quality of
calls on a wireless phone depends onthe strength of the wireless radio signal.
Checking signal strength
When you are at the start screen (seepage16) or in a call, the signal
strength is indicated by the indicators on the left side of your phone’s
display. These indicators scroll as the strength of the signal increases
and decreases.
Increasing your phone’s signal may be easy. Try moving your phone
slightly, or move towards a window if you’re calling from inside a building.
Using the slide
If you activate the slide setting, you can answer and end calls simply by
opening or closing the slide. Your phone will also prompt you to activate the
keyguard once you close the slide.
Activating and deactivating the slide setting
Press 0HQX 4 2 6 (6HWWLQJV - 3KRQHVHWWLQJV - 6OLGHVHWWLQJ)
Scroll to 2Q to activate the slide, or 2II to deactivate the slide and press 2.
Note: If you’re using a headset and wish to close the keypad cover and still
keep the call active, press
2SWLRQV once before closing the keypad cover.
Making a call
When you want to make a call, open the slide, enter the area code and phone
number and press B

12
Editing a number on display
Press s tomovethecursortothe leftand t tomove itto theright.Press&OHDU
to delete the character to the left of the cursor.
Dialing stored phone numbers
View stored names and numbers by pressing t or s from the start screen (see
page16), then press B
See “Phone book” on page 57 for details on storing numbers.
Calling card calls
See “Calling card” on page 29.
Emergency calls
See “Emergency calls” on page 40.
Ending a call
If 6OLGHVHWWLQJ is active, simply close the keypad cover. Otherwise, press E
See “Using the slide” on page 11.
Answering a call
The phone rings according to the settings in the currently
selected profile (seepage 61).
If 6OLGHVHWWLQJ is active, simply open the slide to answer the call. Otherwise,
press any key except Eor P
Note: If Keyguard is on (see page 13), only Banswers calls. See “Using the
slide” on page 11.
8860 UG version 0.01 3/15/99 13
The Basics
Want to stop your phone from ringing without answering
the call ?
Press Pquickly when the phone rings. This keeps you from answering a call if
it’s inconvenient to talk.
You can still answer the call if &DOO or the name of the person who is calling is
still flashing on your display.
If you don’t wish to answer thecall, it will be forwardedto your voice mailbox
if you have a voice mail subscription.
Keyguard
This featurehelps to prevent accidental key presses (e.g. when your phone is in
your pocket, in your purse) by locking your keypad.
If any keys are pressed while Keyguard is activated, 3UHVV
8QORFNDQGWKHQ will display.
Using Keyguard with the slide
When 6OLGHVHWWLQJ is activated, your phone will display
/RFNNH\V in the lower left part of the display. Press the key underneath /RFN
NH\V and your Keyguard will be activated.
If you don’t wish to activate Keyguard at this time, press 4XLW or simply wait
about five seconds and it will disappear.
Keyguard will deactivate each time you open the slide.
Activating Keyguard without the slide
There are three different ways to activate Keyguard. .H\VORFNHG will appear
on the display when activated.
• Press and hold E
• Press
0HQX ∗
• Press
0HQX 9 at the start screen

14
Deactivating Keyguard
• Press 8QORFN then 
• Press and hold Euntil 8QORFNNH\V" appears and press 2.
Note: When Keyguard is 21, calls to the emergencynumber programmed into
yourphone(e.g. bypressing911thenB)maybepossible.However,Emergency
key 9 doesn’t work.
Answering a call with Keyguard active
During an incoming call the keypad automatically unlocks. However, you can
answer a call only byopening the keypad cover if it’s active; otherwise, press
only B. After you end the call, Keyguard automatically becomes active again.
Some notes about Keyguard
• Calls may be possible to the emergency number programmed into your
phone (e.g. 911 or other official emergency number). The number is
displayed only after you have keyed in its last digit.
• Pressing the Pkey quickly turns lights on for 15 seconds.
Note: Keyguard is automatically turned off when the phone is connected to a
car kit.
8860 UG version 0.01 3/15/99 15
Using Your Phone
4. Using Your Phone
The first few days you have your phone, play with it to learn how the menu
and submenu system works.
The more you learn how to access these menus and submenus, the more fun
you’ll have with your phone.
This section describes the different methods of using your phone menus and
submenus.
The Display
Soft keys
Yourphonehastwosoftkeyslocatedbelowthedisplay.The
current function is indicated by the texts appearing
directlyabovethem. Pressthecorrespondingkeyunderthe
choice you wish to select.
This illustration shows the phone at the start screen
(see“Whatis the ‘startscreen’?” onpage16). The start
screen always displays 0HQX on the left and 1DPHV on the right. 0HQX allows
you to access your phone’s menus and submenus. 1DPHV allows you to access
your phone book (see“Phone book”onpage 57).
Scroll keys
Your phone has a scroll key located just below the display screen. The scroll
key has two arrows on it that look like
s and t . Press these to navigate
through your phone’s menus and submenus, as well as through your phone
book. (See “Phone book” on page 57).

16
Scroll bar
When you access your phone’s menu and submenus, you will notice a
scroll bar at the far right of the screen. This bar indicates your location
in the menu structure; each “tab” on the bar represents a different
menu item.
For example, press 0HQX once. The scroll bar appears with the first (top) tab
displayed. A differenttab appears each time you press the
t or s key to move
up and down through the menu structure. The scroll bar works the same way
with submenus.
Menu & submenu numbering
When you scroll to a menu or submenu, the menu number and/or submenu
number appears on the display above the scroll bar.
For example, when you scroll to menu 2 (&DOOORJ) the number appears in the
top right-hand corner of the display. If you scroll to menu 4 (6HWWLQJV),
submenu 3 (6HFXULW\VHWWLQJV), your phone will display  in the top right-
hand corner.
See “Summary of Menu Items” on page 17 for a list of your phone’s features
along with their menu locations.
Also, see “Using shortcuts” on page 17.
What is the ‘start screen’?
The start screen appears when you first turn your phone on, in its idle state.
When you want to get to the start screen, press Eat any time except during
a call (unless you want to hang up).
Note: If you press Ewhen the phone is requesting input
(i.e., a setting, phone number, name, etc.), the phone displays the start screen
and the input is not saved.
8860 UG version 0.01 3/15/99 17
Using Your Phone
Scrolling through the main menu
Press 0HQX at the start screen. Then press t or s to reach the desired menu
item.
Press6HOHFW,2SWLRQVor2. (whichever appears) to enter submenus and to
choose options.
Press ([LW to exit the present menu or %DFN to go back one level.
Using shortcuts
Thisis aquickand easywayto accessamenu without having toscrollthrough
other menus.
Press 0HQX, then menu number, then submenu number.
Press the menu and submenu numbers within a couple of seconds of each
other when using this method.
Fora summaryof yourphone’s menustructure,see“SummaryofMenuItems”
on page 17.
Help text
If you’re not sure how a feature works, wait just a few seconds and help text
will appear formost of your phone’s features. Press 0RUH to see the next page
of the text or %DFN to exit.
Summary of Menu Items
1 Messages
1 1 Text Messages
1 1 1 Inbox

18
1 1 2 Saved
1 1 3 Write new *
1 1 4 Outbox *
1 1 5 Erase all
*Only where available. Please see “Text messages and pages” on page 71 for details.
1 2Voice messages
1 2 1Listen to voice messages
1 2 2Voice mailbox number
1 3Welcome Note
2Call log
2 1Missed calls
2 2Dialed calls
2 3Received calls
2 4Clear call lists
2 5Call timers
3Profiles
3 1Normal (followingsubmenusappear inallprofiles)
3 1 1Select
3 1 2Customize
3 1 2 1Ringing options
3 1 2 2 Ringing volume
3 1 2 3 Ringing tone
3 1 2 4 Vibrating alert (w/vibrating batteryonly)
3 1 2 5 Keypad tones
3 1 2 6 Warning and game tones
3 1 2 7 Message alert tone
8860 UG version 0.01 3/15/99 19
Using Your Phone
3 1 2 8 Lights (only in
&DU profile)
3 1 2 9 Automatic answer (only in &DU and +HDGVHW )
3 1 3Rename (notavailablein
1RUPDO profile)
3 2Silent
3 3Meeting
3 4Outdoor
3 5Pager
3 6Car (once used with car kit)
3 7Headset (once used with headset)
4Settings
4 1Call settings
4 1 1Emergency key 9
4 1 2Automatic redial
4 1 3Calling card
4 2Phone settings
4 2 1Clock
4 2 2Alarm clock
4 2 3Touch tones
4 2 4Restore factory settings
4 2 5Language
4 2 5 1English
4 2 5 2Français
4 2 5 3Español
4 2 5 4Português
4 2 5 5Russian
4 2 5 6Hebrew

20
4 2 5 7Chinese Traditional
4 2 6Slide setting
4 3Security settings
4 3 1Restrict calls
4 3 2Access codes
4 4Network services
4 4 1Voice privacy
4 4 2Call forwarding
4 4 3Call waiting
4 4 4Send own number
4 4 5Network feature setting
4 4 6NAM selection
5System
5 1Automatic
5 2Manual
5 3New search
6Games
6 1Memory
6 2Snake
6 3Logic
6 4Rotation
7Calculator
8Calendar
9Keyguard
8860 UG version 0.01 3/15/99 21
Features A to Z
5. Features Ato Z
ABC mode
This allows you to enter names into your phone book.
See “Entering letters and numbers” on page 42.
Access codes
This is a security feature that allows you access to certain phone features,
such as the phone lock (page 59)and unlocked phone number (page78).
Also, see “Lock code” on page 49 and “Security code” on page 68.
Alarm clock
The alarm clock operates off your phone’s clock. The
volume for the alarm clock is determined by the current
ringing volume.
Note: If you have selected the
6LOHQW or %HHSRQFH ringing
option (see page 64), your alarm clock will quietly beep one time.
See “Clock” on page 36 for information on your phone’s clock.
Setting the alarm clock
Press 0HQX 4 2 2 (6HWWLQJV - 3KRQHVHWWLQJV - $ODUPFORFN)
Enter time you wish to set alarm (use two-digit fields for hours and minutes).
Existing digits will be replaced with the new alarm time.
Press 2.

22
Select either DP or SP and press 2.
Note: Step 4 appears only if youhave selected am/pm format; see “Selecting
time format” on page 37 for more information.
When the alarm goes off
Press 6WRS to shut off the alarm.
Snoozing
Press 6QRR]H.
The alarm will go off again in 10 minutes. If you let the phone alarm for 1
minute without pressing a key, it stops alarming for 10 minutes then starts
again.
Turning the alarm clock off
Press 0HQX 4 2 2 (6HWWLQJV - 3KRQHVHWWLQJV - $ODUPFORFN), then scroll to 2II
and press 2..
Note: If you have selected the
6LOHQW or 0HHWLQJ profile, your alarm will only
beep once. The best profile to use while using the alarm clock is
1RUPDO or
2XWGRRU , unless these have been modified from their original settings.
For more information on Profiles, see page 61.
All calls timer
This feature keeps track of how much time you have spent on all calls with
your phone.
See “Call timers” on page 34.
Automatic answer
This is one of the settings in your phone’s Profiles (seepage 61). With this on,
your phone answers incoming voice calls after one ring.
8860 UG version 0.01 3/15/99 23
Features A to Z
Note: This can only be used when your phone is connected to a headset or to
an approved handsfree car kit equipped with the ignition sense option, with
the ignition on.
Activating automatic answer
Press 0HQX 3 (3URILOHV)
Your phone lists each profile. Use
t to highlight either the &DU or +HDGVHW
profile and press 2SWLRQV.
Note:
&DU and +HDGVHW will not appear unless your phone has already been
connected to a car kit or headset at least one time.
Highlight &XVWRPL]H and press 2.. Press
t to $XWRPDWLFDQVZHU, then press
6HOHFW again.
Press
t to 2Q and press 2..
Note: This feature will not function with data calls.
Automatic redial
Your phone will redial the number you’re trying to call up to 3 times after you
hear a quick, busy signal. Press Eto stop the call attempts.
This feature attempts to redial numbers that are busy due to the wireless
network. It will not redial numbers to a busy party.
Activating automatic redial
Press 0HQX 4 1 2 (6HWWLQJV - &DOOVHWWLQJV - $XWRPDWLFUHGLDO), then press t or
s to 2Q and press 2..

24
Calculator
Your phone’s calculator adds, subtracts, multiplies, divides,
and converts currency.
Remember! Your phone must be switched on to use this
feature. Do not switch on the phone when wireless phone
use is prohibited or when it may cause interference or danger.
Using the calculator
Press 0HQX 7 (&DOFXODWRU)
Enter the first number in the calculation (press # for decimals)
To add, press ∗(+appears)
To subtract, press ∗∗ twice (- appears)
To multiply, press ∗∗∗ (* appears)
To divide, press ∗∗∗∗ ( / appears)
To add a decimal, press the # key
Enter the second number
Repeat these steps as many times as needed. Press &OHDU to erase any
mistakes.
Press 2SWLRQV. With (TXDOVhighlightedpress 2.
Note: You can also choose
$GG , 6XEWUDFW , 0XOWLSO\ , and 'LYLGH from the list of
options.
Storing exchange rates
Press 0HQX 7, then press 2SWLRQV
Scroll to ([FKDQJHUDWHand press 2.
Press
t or s at either +RZPDQ\KRPHXQLWVWRDYLVLWHGXQLW or +RZPDQ\
YLVLWHGXQLWVWRDKRPHXQLW, depending on how you wish to convert the
currency. Press 2. once you decide.
Enter the appropriate exchange rate and press 2. (use the # key for decimals)
Phone will display 5DWHVDYHG
8860 UG version 0.01 3/15/99 25
Features A to Z
Calculating exchange rates
Press 0HQX 7
Enter number of units, then press 2SWLRQV
Press
t or s to either 7RKRPH or 7RYLVLWHG, and press 2.
Converted currency will display
Calendar
The calendar keeps track of birthdays, meetings, simple
reminders, and calls you need to make. It can even sound
an alarm when it’s time for you to make a call or go to a
meeting.
Remember!Yourphonemust beswitchedon tousethis feature.Do notswitch
on the phone when wireless phone use is prohibited or when it may cause
interference or danger.
Note: Your phone must remain on to use the calendar’s alarm feature. If your
phone is off, the alarm will not sound at its scheduled time.
Using the calendar
Press 0HQX 8 (&DOHQGDU)
If you haven’t set the time and date, your phone prompts you to set your
phone’s clock
When your phone prompts you for the time with KKPP, enter the time in
hours and minutes
(using two-digit fields), then press 2.
Time format (24-hour or am/pm) is set using the Clock.
See “Selecting time format” on page 37.
Whenyourphonepromptsyoufor thedatewithPPGG\\\\,enter themonth
and day (using two-digit fields) and year (using a four-digit field), then press
2..

26
Tip: Use t to move the cursor right and s to move it left. When you enter a
digit, it writes over the number to the right of the cursor.
Your phone displays the current day. You can also scroll to different days by
pressing
t or s .
Once you’re at the date you want, press 2SWLRQV. Then use
t to highlight the
option you want, and press 6HOHFW The options are:
Option 1: View day
With this option, you can view the notes of the day currently on display.
Use
t to scroll through the notes. Each note allows you to choose the
following 2SWLRQV:
(UDVH clears the note from your calendar.
(GLW gives you the same prompts you got when you made the note.
0RYH gives you the date prompt so you can move the note to another date.
Option 2: Make note
With this option, you’ll need to choose 5HPLQGHU, &DOO, 0HHWLQJ, or %LUWKGD\.
Your phone will prompt you for more information depending on which one
you choose. You can also set an alarm for any calendar note.
See “Entering letters and numbers” on page 42 for help with entering
information at the
6XEMHFW prompt.
Note: When the alarm goes off, you can press
3RVWSRQH or 2. . Press 2. to shut
off the alarm.
Option 3: Erase notes
With this option, you’ll need to choose which notes to erase. If you choose all
the notes for the day currently on display (2I&KRVHQ'D\), or 2QH%\2QH (for
all notes in the calendar), your phone presents each note to you with the
option (UDVH or %DFN.
If you choose $OODW2QFH, your phone will delete all calendar notes. When
prompted to confirm the erase, press <HV or 1R.
8860 UG version 0.01 3/15/99 27
Features A to Z
Option 4: View all
This allows you to view the notes of the entire calendar. Use t or s to scroll
through the notes. &DOHQGDUPHPRU\HPSW\ will appear if there are no notes
in the calendar.
Option 5: Go to date
Enter the date you wish to go to.
Option 6: Set the date
Enter the day and month (using two-digit fields) and year (using a four-digit
field), then press 2..
Caller groups
You can create groups of names in your 3KRQHERRN
(seepage 57), and give each group a different ringing tone. Then you’ll know
when someone from that group is calling you because of the way the phone
rings.
Adding names to a caller group
Note: The names and numbers that you add to a group must already be stored
in your phone book. See “Storing a name and number” on page 58.
With the display clear, press
t until you see the name or number you want
Press 'HWDLOV, if shown, or skip to Step 3
Press 2SWLRQV
Use
t to reach &DOOHUJURXSV. Press 6HOHFW.
Use
t to reachthegroup towhichyouwant toaddthis nameornumber.Press
6HOHFW.
Defining a ringing tone for a caller group
With the display clear, press 1DPHV

28
Press
t to reach &DOOHUJURXSV. Press 6HOHFW
Use
t to reach the group you want. Press 6HOHFW
Press
t until you see*URXSULQJLQJWRQH. Press 6HOHFW. Use t toreach the tone
you want to hear when anyone from this group calls you. Press 2..
Tip: You can set your phone to ring only when people from certain caller
groups call you, and to otherwise be silent.
See the “Caller group” description under “Ringing options” on page 64.
Renaming a caller group
Follow steps 1-3 in “Defininga ringingtonefor acallergroup”
Press
t until you see 5HQDPHJURXS. Press 6HOHFW.
Enter the group name (see “Entering letters and numbers” on page 42 for
details)and press 2.
Removing names from a caller group
Follow steps 1-4 in “Adding names toacaller group”
Use
t to reach 1RJURXS. Press 6HOHFW.
Caller group graphics
When someone calls you from a particular caller group, your phone can
display a graphic to identify which caller group that person is calling from.
Press 1DPHV, scroll to &DOOHUJURXSV, then press 6HOHFW
Scroll to the caller group you wish to display the graphic for and press 6HOHFW
Scroll to *URXSJUDSKLF and press 6HOHFW
Scroll to 2Q to display the graphic that goes with that particular caller group
Caller ID
This is a network service that helps identify incoming calls. Contact your
service provider for details.
8860 UG version 0.01 3/15/99 29
Features A to Z
When Caller ID is active, your phone may display the caller’s phone number.
The caller’s name may also display iftheir name and number has been stored
in the phone book (see “Phone book”on page 57) or if the wireless network
supports it.
&DOO or &DOOFDOOHU,'XQDYDLODEOH will display when the wireless network
doesn’t recognize the calling number.Also, &DOOFDOOHU,'EORFNHG may display
if the calling party has blocked caller ID.
Calling card
If you wish to use a calling card for long distance calls, you
must first store your calling card information into your
phone. Your phone can store up to four calling cards.
Storing your calling card
Press 0HQX 4 1 3 (6HWWLQJV - &DOOVHWWLQJV - &DOOLQJFDUG)
Scroll to desired calling card and press 2SWLRQV
Press
t or s to (GLW, press 2.
Enter security code and press 2.
Press 6HOHFW at 'LDOLQJVHTXHQFH. Select the dialing sequence your card uses
(use chart below), press
t or s to choose sequence, then press 6HOHFW
Note: The order of the following steps may vary, depending on which dialing
sequence your card uses.
Enter access number when prompted for the calling card’s access number
(usually the 1-800 number listed on the back of the calling card), press 2.
Note: You can also retrieve the access number from your phone book if it has
already been stored. Simply press
6HDUFK , then t or s to find the number.
Enter card number and/or PIN when prompted to enter calling card number
and personal identification number, then press 2.Press 2. again at 6DYH
FKDQJHV?

30
Press
t or s to &DUGQDPH and press 6HOHFW. Enter card name using your
phone’s keypad, press 2..
See “Entering letters and numbers” on page 42 if you need help on entering
the card name
For details about your phone’s security code, see “Security code” on page 68.
*These calling cards are frequently used with these dialing sequences.
However, they may vary and are subject to change at the phone company’s
discretion.
Choosing a calling card to use
Press 0HQX 4 1 3 (6HWWLQJV - &DOOVHWWLQJV - &DOOLQJFDUG)
Scroll to desired card and press 2SWLRQV
Press
t or s to highlight 6HOHFW and press 2..
Dialing
Sequence Useforcardsthatrequire you to: Cards using this sequence*
Access no.
+ phone no.
+ card no.
Dial 1-800 access
number, then phone
number, then card
number (+ PIN if
required)
MCI,AT&TTrue
Choice, Sprint
Canada, Unitel
Access no.
+ card no.
+ phone no.
Dial 1-800 access
number, then card
number (+ PIN if
required), then phone
number
networkMCI,
WorldPhone
MCI
Prefix
+ phone no.
+ card no.
Dial the prefix (any
numbers that must
precede the phone
number) and phone
number you wanttodial,
then card number, (then
PIN, if required)
GTE, PacBell,
AT&T, Stentor
8860 UG version 0.01 3/15/99 31
Features A to Z
Enter security code at 6HFXULW\FRGH, press 2.
Your phone will display &DUGUHDG\IRUXVH
Making calling card calls
Enter the phone number, including any prefix (such as 0 or 1) that your calling
card may require when you make a calling card call. See your calling card for
instructions.
Press and hold Bfor a few seconds until your phone displays &DUGFDOO.
Press 2. when you see :DLWIRUWRQHWKHQSUHVV2.. When you see :DLWIRU
WRQHSUHVV2.DJDLQ, press 2. again.
Note: This procedure may not apply to all calling card options programmed
into your phone. Please look at the back of your calling card or contact your
long distance company for more information.
Call forwarding
This network service is used to forward incoming calls to another number so
you won’t miss an important call. Check with your service provider for details.
Note: Before you can activate this feature, you should first store the feature
code given to you by your service provider. Otherwise, this feature may not
appear in the menu.
However, you can use the feature code manually, if you choose, by including
the feature code in front of the phone number
(e.g., *72 555 1212)
See “Network feature setting” on page 53 for more details.
Press 0HQX 4 4 2 (6HWWLQJV - 1HWZRUNVHUYLFHV - &DOOIRUZDUGLQJ)
Scroll to desired call forwarding feature (see options below) and press 6HOHFW
Highlight $FWLYDWH and press 2.
Enter phone number at 1XPEHU(or press 6HDUFK to locate number in phone
book) and press 2.

32
Your phone will attempt to call the network to confirm the feature code you
entered in Menu 4 4 5 (see“Networkfeaturesetting”on page53)
Once the feature code had been confirmed, the feature is activated
Call forwarding options
)RUZDUGDOOFDOOV forwards all incoming calls.
)RUZDUGLIEXV\ forwards calls only when you’re on the phone.
)RUZDUGLIQRWDQVZHUHG forwards calls if you don’t answer.
)RUZDUGLIRXWRIUHDFK forwards calls if you are out of the serving wireless
network.
&DQFHODOOFDOOIRUZDUGLQJ cancels all call forwarding options you have active.
Call log
This feature automatically keeps track of numbers you’ve
dialed, numbers that have called you, and the amount of
time you’ve spent on calls.
Using call log
Press 0HQX 2 (&DOOORJ)
Scroll to one of the following options, then press 6HOHFW or 2.
2-10LVVHGFDOOV - See page52.
2-2'LDOHGFDOOV- See page39.
2-3 5HFHLYHGFDOOV - See page62.
2-4&OHDUFDOOOLVWV - Seepage 36.
2-5 &DOOWLPHUV- See page 34.
Tip: You can dial any of the phone numbers by pressing Bwhile the number
is on the display.
8860 UG version 0.01 3/15/99 33
Features A to Z
The ‘Options’ soft key
When youaccess'LDOHGFDOOV,5HFHLYHGFDOOV,or0LVVHGFDOOV andpress2SWLRQV,
a list of options will appear on your phone’s display.
&DOOWLPH shows the date and time when the call was first connected (if clock
has been set)
(GLWQXPEHU allows you to edit the dialed number.
6DYH allows you to save the number into your phone book.
(UDVH will erase the number from the call list.
9LHZQXPEHU willappearonlyifthenumberhasbeenstoredin thephonebook
and the name is displayed instead of the number.
Call restrictions
This feature allows you to restrict incoming and outgoing calls to and from
certain numbers.
See “Restrict calls” on page 63 for details.
Call settings
This feature allows you to access and activate some of your phone’s features.
Using call settings
Press 0HQX 4 1 (6HWWLQJV - &DOOVHWWLQJV)
Press
t to reach one of the following options, then press 6HOHFW
4-1-1 (PHUJHQF\NH\ - See page41.
4-1-2 $XWRPDWLFUHGLDO - See page 23.
4-1-3 &DOOLQJFDUG - Seepage29.

34
Call timers
Your phone automatically keeps track of the amount of
time you’ve spent in calls.
Press 0HQX 2 5 (&DOOORJ - &DOOWLPHUV)
Scroll repeatedly to access the following options
/DVWFDOOdisplays call duration of last call.
$OOFDOOVdisplays call duration of all calls made since timers have last been
reset (seepage36 fordetailson howtoclear calltimers).
/LIHWLPHU shows duration of all calls; this can not be reset (see page 48).
&OHDUWLPHUV clears all call timers except the Life timer (seepage 36).
These calldurationsare for thecurrently-selectedNAM (phone number).Your
phone has separate timers for each NAM your phone uses, except for the Life
timer.
See “NAM selection” on page 53 for details on NAM.
Note: The actual time invoiced for calls by your service provider may vary,
depending upon items such as network features, rounding off for billing, and
taxes.
Call waiting
If you have subscribed to Call Waiting, your phone will beep during a call let
you know you have an incoming call. Your phone may also display the
incoming caller’s identification (see “Caller ID” on page28).
Answering an incoming call with call waiting
Press B
Swapping between two calls
Press B
8860 UG version 0.01 3/15/99 35
Features A to Z
Ending the calls
Press Eto end both calls
Activating call waiting
You can also activate this feature with your phone; simply ask your service
provider for the feature code, store it into your phone, then activate it.
Note:Thisfeaturemaynotappearinyourphone’smenuuntilthefeaturecode
has been stored.
See “Network feature setting” on page 53 for more details.
Press 0HQX 4 4 3 (6HWWLQJV - 1HWZRUNVHUYLFHV - &DOOZDLWLQJ)
Scroll to $FWLYDWH(or select &DQFHO to cancel and press 2.
Your phone will attempt to call the network to confirm the feature code you
entered in Menu 4 4 5 (see “Networkfeaturesetting” onpage 53)
Once the feature code has been confirmed, the feature is activated.
Change lock code
This feature allows you to change your lock code.
See “Changing your lock code” on page 49.
Change security code
This feature allows you to change your security code.
See “Changing your security code” on page 68.

36
Clear call lists
Thisfeaturewill clearall dialednumbers,as wellas numbersof answered calls
and missed calls. You can not undo this operation, so be careful.
Also, see “Call log” on page 32.
Press 0HQX 2 4 (&DOOORJ - &OHDUFDOOOLVWV)
Highlight either $OO, 0LVVHG, 'LDOHG, or 5HFHLYHG and press 2. ($OO will clear all
call lists, while the others clear their respective call lists)
Clear timers
This feature clears all call timers for the currently-selected NAM. See“Call
timers” on page34 for more details.
Press 0HQX 2 5 4 (&DOOORJ - &DOOWLPHUV - &OHDUWLPHUV)
Enter security code at 6HFXULW\FRGHand press 2.
Careful: Clearingcalltimerscannotbeundone.Ifyouareusingthecalltimers
to log or track the amount of time you are using your phone, you may wish to
record the calltimers before you erasethem.
Note: The Life timer contains important warranty information and can not be
reset. See “Life timer” on page 48 for details.
Clock
Your phone has an internal clock that can be displayed or
hidden.
It also features an alarm clock
(seepage21).
8860 UG version 0.01 3/15/99 37
Features A to Z
Note: The clock is powered by your phone’s battery. If your clock has been
activated and you remove the battery while your phone is still on, you will
need to reset the time after you turn your phone back on.
However, if you first turn your phone off before removing the battery, your
phone will retain the time and date it had before the battery was removed.
Setting the clock
Press 0HQX 4 2 1 (6HWWLQJV - 3KRQHVHWWLQJV - &ORFN)
Scroll to $GMXVWWLPH and press 6HOHFW
Enter present time at 7LPH (use two-digit fields for hours and minutes)
Press 2.
Select DP or SP and press 2. (if am/pm format has been selected; see below)
Selecting time format
Press 0HQX 4 2 1 (6HWWLQJV - 3KRQHVHWWLQJV - &ORFN)
Scroll to 7LPHIRUPDW and press 6HOHFW
Scroll to either KRXU or DPSP
Press 2.
Displaying or hiding the clock
Press 0HQX 4 2 1 (6HWWLQJV - 3KRQHVHWWLQJV - &ORFN)
Scroll to either +LGHFORFN or'LVSOD\FORFN (only one will display depending on
the current setting)
Press 6HOHFW
Conference call
This feature allows you to add a third party to a call. You can use this feature
with local and long distance calls.