Nokia Lumia 710 User manual

Service Manual for L1 and L2
Nokia Lumia 710
RM-803, RM-809
Key features
z
Windows Phone Mango operating system
z
Large 3.7" LCD TFT ClearBlack screen (not OLED)
z
Sync, store and share media files
z
Best instant social experience
z
Fast browsing with IE9
V
ersion 1.
0
Exploded view Disassembly steps Disassembly video
Assembly hints Assembly hints video Service devices
Solder components Product controls and interfaces Service concept
Phone reset
©2011 Nokia | Confidential | All Rights Reserved.
Mor
e
Mor
e
Mor
e
Mor
e
Mor
e
Mor
e
Mor
e
Mor
e
Mor
e
Mor
e

Service Manual Level 1 and 2
Nokia Lumia 710
RM-803, RM-809
Version 1.0
Exploded view
CAMERA
I0013
AV JACK
I0017
EARPIECE
I0003
A-COVER
I0004
DISPLAY CONDUCTIVE
TAPE
I0006
DIPRO GASKET
I0010
CAMERA LENS BOOT
I0014
LED FLASH
I0018
FLASH SUPPORT
I0025
FLASH BOOT
I0019
DISPLAY
I0005
UI KEYMAT DOMESHEET
I0007
IHF SPEAKER
I0015
SHIELD ADHESIVE
I0011
LIGHT SWAP PWB
I0008
SPEAKER GASKET
I0016
USB BOOT
I0012
MAIN ANTENNA
I0021
BATTERY COVER
I0024
MAIN CHASSIS
I0022
TYPE LABEL
I0009
CAMERA CROSS SCREW
I0023
A-COVER ASSEMBLY
(I0001, I0002, I0004)
LIGHT SWAP PACKAGE
(I0006 - I0011)
2
MAIN CHASSIS ASSEMBLY
(I0015 - I0022)
3
v1.0 Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
©2011 Nokia | Confidential | All Rights Reserved.

Service Manual Level 1 and 2
Nokia Lumia 710
RM-803, RM-809
Version 1.0
Disassembly steps
For disassembling you need the Nokia Standard Toolkit version 2. You will also need the camera removal
tool SS-278 and an AV plug.
Protect the A-COVER with protective film.

Use the opening notch on the left side of the device to release the BATTERY COVER.
Remove the BATTERY COVER.

Unscrew the eleven camera cross screws in the order shown. Do not use them again. Discard them.
Push the MAIN CHASSIS slightly forward and lift up the bottom end. Remove the MAIN CHASSIS.

Remove the CAMERA LENS BOOT with tweezers. Use plastic tweezers if available.
Remove the FLASH SUPPORT with tweezers.

Open the TOUCH WINDOW connector with the SS-93. Be careful not to damage the connector.
Use the SS-93 to lift up and push forward the ENGINE BOARD from the shown place. Be careful not to
damage the shown springs!

Then carefully turn over the engine board as shown. While turning the ENGINE BOARD, be careful not to
damage the two shown connectors.
Open the DISPLAY connector with the SS-93. Be careful not to damage the connector or components
nearby.

The ENGINE BOARD can now be separated.
Lift up the EARPIECE with the dental tool. Be careful not to injure yourself with the sharp end of the
dental tool.

Remove the EARPIECE with tweezers. When removing the EARPIECE, make sure not to touch the shown
part of it.
Use the SS-93 to release the DISPLAY. Start from the shown corner. Lift the corner and hold it up for a
while. The adhesive on the DISPLAY GASKET will slowly loosen up making it easier to remove the DISPLAY.
Be careful not to bend the DISPLAY or damage the TOUCH WINDOW connector.