Nokia X3 User manual

Nokia X3
RM-540
Service Manual Level 1&2
1 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
SERVICE MANUAL
Level 1&2
RM-540
Transceiver characteristics
Band:
GSM Quadband 850/900/1800/1900 Mhz
Display:
2.2" Active TFT, 262K colors, 240x320 pixel resolution
Camera:
3.2 MPix CMOS, 4x zoom, Extended depth of field
(EDOF)
Operating System:
S40 6th Edition
Connections:
USB 2.0 (micro USB), Bluetooth 2.1 + EDR + A2DP +
AVRCP, 3.5mm stereo headphone plug
Transceiver with BL-4CT battery pack
Talk time Standby
GSM:
Up to 7.5 hours
GSM:
Up to 380 hours
Note:
Talk times are dependant on network parameters and
phone settings

Nokia X3
RM-540
Service Manual Level 1&2
2 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
Table of contents
1.Change history ...............................................................................................................................................................................3
2.Copyright..........................................................................................................................................................................................4
3.Warnings and cautions...............................................................................................................................................................5
3.1Warnings ................................................................................................................................................................................5
3.2Cautions ..................................................................................................................................................................................5
4.ESD protection................................................................................................................................................................................6
5.Care and maintenance ................................................................................................................................................................7
6.Battery information .....................................................................................................................................................................8
7.Exploded view................................................................................................................................................................................9
8.Service devices .............................................................................................................................................................................10
9.Software update..........................................................................................................................................................................11
10.Disassembly instructions.....................................................................................................................................................12
11.Assembly hints ........................................................................................................................................................................19
12.Solder components................................................................................................................................................................20

Nokia X3
RM-540
Service Manual Level 1&2
3 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
1. CHANGE HISTORY
Status Version No. Date Comments
Approved 1.0 9.10.2009 First approved version
The purpose of this document is to help Nokia service levels 1 and 2 workshop technicians to
carry out service to Nokia products. This Service Manual is to be used only by authorized Nokia
service suppliers, and the content of it is confidential. Please note that Nokia provides also other
guidance documents (e.g. Service Bulletins) for service suppliers, follow these regularly and
comply with the given instructions.
While every endeavor has been made to ensure the accuracy of this document, some errors may
exist. If you find any errors or if you have further suggestions, please notify Nokia using the
address below:
Nokia Care Academy
mailto:[email protected]m
Please keep in mind also that this documentation is continuously being updated and modified,
so watch always out for the newest version.

Nokia X3
RM-540
Service Manual Level 1&2
4 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
2. COPYRIGHT
Copyright © 2009 Nokia. All rights reserved.
Reproduction, transfer, distribution or storage of part or all of the contents in this document in
any form without the prior written permission of Nokia is prohibited.
Nokia, Nokia Connecting People, and Nokia X and Y are trademarks or registered trademarks of
Nokia Corporation. Other product and company names mentioned herein may be trademarks or
tradenames of their respective owners.
Nokia operates a policy of continuous development. Nokia reserves the right to make changes
and improvements to any of the products described in this document without prior notice.
Under no circumstances shall Nokia be responsible for any loss of data or income or any special,
incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided “as is”. Except as required by applicable law, no
warranties of any kind, either express or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose, are made in relation to the
accuracy, reliability or contents of this document. Nokia reserves the right to revise this
document or withdraw it at any time without prior notice.
The availability of particular products may vary by region.
IMPORTANT
This document is intended for use by qualified service personnel only.

Nokia X3
RM-540
Service Manual Level 1&2
5 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
3. WARNINGS AND CAUTIONS
Please refer to the phone’s user guide for instructions relating to operation, care and
maintenance including important safety information. Note also the following:
3.1 Warnings
1. CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE
MANAGEMENT SYSTEMS AND ANTI–SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS,
EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE
DEALER/MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF
ENERGY.
2. THE HANDPORTABLE TELEPHONE MUST NOT BE OPERATED IN AREAS LIKELY TO CONTAIN
POTENTIALLY EXPLOSIVE ATMOSPHERES, EG PETROL STATIONS (SERVICE STATIONS), BLASTING
AREAS ETC.
3. OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT, INCLUDING CELLULAR TELEPHONES, MAY
INTERFERE WITH THE FUNCTIONALITY OF INADEQUATELY PROTECTED MEDICAL DEVICES. CONSULT
A PHYSICIAN OR THE MANUFACTURER OF THE MEDICAL DEVICE IF YOU HAVE ANY QUESTIONS.
OTHER ELECTRONIC EQUIPMENT MAY ALSO BE SUBJECT TO INTERFERENCE.
3.2 Cautions
1. Servicing and alignment must be undertaken by qualified personnel only.
2. Ensure all work is carried out at an anti–static workstation and that an anti–static wrist
strap is worn.
3. Use only approved components as specified in the parts list.
4. Ensure all components, modules screws and insulators are correctly re–fitted after servicing
and alignment.
5. Ensure all cables and wires are repositioned correctly

Nokia X3
RM-540
Service Manual Level 1&2
6 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
4. ESD PROTECTION
Nokia requires that service points have sufficient ESD protection (against static
electricity) when servicing the phone.
Any product of which the covers are removed must be handled with ESD
protection. The SIM card can be replaced without ESD protection if the product
is otherwise ready for use.
To replace the covers ESD protection must be applied.
All electronic parts of the product are susceptible to ESD. Resistors, too, can be
damaged by static electricity discharge.
All ESD sensitive parts must be packed in metallized protective bags during
shipping and handling outside any ESD Protected Area (EPA).
Every repair action involving opening the product or handling the product
components must be done under ESD protection.
ESD protected spare part packages MUST NOT be opened/closed out of an ESD
Protected Area.
For more information and local requirements about ESD protection and ESD
Protected Area, contact your local Nokia After Market Services representative.

Nokia X3
RM-540
Service Manual Level 1&2
7 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
5. CARE AND MAINTENANCE
This product is of superior design and craftsmanship and should be treated with care. The
suggestions below will help you to fulfil any warranty obligations and to enjoy this product for
many years.
Keep the phone and all its parts and accessories out of the reach of small children.
Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can
contain minerals that will corrode electronic circuits.
Do not use or store the phone in dusty, dirty areas. Its moving parts can be
damaged.
Do not store the phone in hot areas. High temperatures can shorten the life of
electronic devices, damage batteries, and warp or melt certain plastics.
Do not store the phone in cold areas. When it warms up (to its normal temperature),
moisture can form inside, which may damage electronic circuit boards.
Do not drop, knock or shake the phone. Rough handling can break internal circuit
boards.
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the
phone.
Do not paint the phone. Paint can clog the moving parts and prevent proper
operation.
Use only the supplied or an approved replacement antenna. Unauthorised antennas,
modifications or attachments could damage the phone and may violate regulations
governing radio devices.
All of the above suggestions apply equally to the product, battery, charger or any accessory.

Nokia X3
RM-540
Service Manual Level 1&2
8 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
6. BATTERY INFORMATION
Note: A new battery’s full performance is achieved only after two or three complete charge and
discharge cycles! The battery can be charged and discharged hundreds of times but it will
eventually wear out.
When the operating time (talk-time and standby time) is noticeably shorter than normal, it is
time to buy a new battery. Use only batteries approved by the phone manufacturer and
recharge the battery only with the chargers approved by the manufacturer.
Unplug the charger when not in use. Do not leave the battery connected to a charger for longer
than a week, since overcharging may shorten its lifetime.
If left unused a fully charged battery will discharge itself over time Temperature extremes can
affect the ability of your battery to charge.
For good operation times with Ni-Cd/NiMh batteries, discharge the battery from time to time by
leaving the product switched on until it turns itself off (or by using the battery discharge facility
of any approved accessory available for the product).
Do not attempt to discharge the battery by any other means Use the battery only for its
intended purpose.
Never use any charger or battery which is damaged.
Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object
(coin, clip or pen) causes direct connection of the + and - terminals of the battery (metal strips
on the battery) for example when you carry a spare battery in your pocket or purse.
Shortcircuiting the terminals may damage the battery or the connecting object.
Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions,
will reduce the capacity and lifetime of the battery. Always try to keep the battery between 15°C
and 25°C (59°F and 77°F).
A phone with a hot or cold battery may temporarily not work, even when the battery is fully
charged. Batteries’ performance is particularly limited in temperatures well below freezing.
Do not dispose batteries in a fire! Dispose of batteries according to local regulations (e.g.
recycling).
Do not dispose as household waste.

Nokia X3
RM-540
Service Manual Level 1&2
9 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
7. EXPLODED VIEW
Only available as
assembly
These parts can not be
reused after removal
Ver. 1.0
SLIDER MODULE ASSEMBLY
(I0102 - I0103)
A-COVER ASSY
I0001
EARPIECE MODULE ASSY
I0004
CONDUCTIVE TAPE DISPLAY
I0102
SCREW M1.4x2.2 TORX+ 5
I0005
SPEAKER MESH TOP
I0206
DC JACK
I0210
AV JACK
I0211
SPEAKER OUTL TRIM TOP ASSY
I0209
USB DOOR
I0214
SCREW M1.6x3.0 TORX+ 6
I0221
F-COVER ASSY
I0222
IHF SPEAKER
I0212
CAMERA MODULE
SMIA65 3.2 EDOF
I0206
B2B CONN SHIELD LID
I0205
A1
LIGHTSWAPPACKAGE
(I0203 - I0207, I9998)
A2
D-COVER ASSY
(I0209 - I0215)
A3
ANTENNA MODULE
(I0216 - I0219)
A4
FUNCTION KEYMAT ASSY
I0002
LCD TFT a-Si 240x320 COG
I0003
SLIDER MODULE
I0103
TYPE LABEL
I0207
SCREW M1 TORX+ 6
I0220
IHF SPEAKER
I0217
NUMERIC KEY ASSY
I0201
DOMESHEET
I0203
LIGHT SWAP PWB
I0204
SPEAKER ADHESIVE
I0218
ANTENNA MODULE
I0219
SPEAKER ADHESIVE
I0213
D-COVER
I0215
CLAPTON EMC MICROPHONE
I0216
E-COVER ASSY
I0202
UI FLEX MODULE ASSY
I0101

Nokia X3
RM-540
Service Manual Level 1&2
10 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
8. SERVICE DEVICES
FLS-5 Flash Device
CA-101 Service Cable
SS-88 Camera Removal tool
AC-8 Travel Charger
BL-4CT Battery
NMP standard toolkit (v2)
For more information, refer to the
Service Bulletin (SB-011) on Nokia
Online. Supplier or manufacturer
contacts for tool re-order can be
found in “Recommended service
equipment” document on Nokia
Online.

Nokia X3
RM-540
Service Manual Level 1&2
11 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
9. SOFTWARE UPDATE
Flash concept – Point of Sale (POS)
To use the FLS-5 Flash Dongle, follow the user guide inside the sales package.
Please check always for the latest version of flash software available on Nokia Online (NOL).

Nokia X3
RM-540
Service Manual Level 1&2
12 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
10. DISASSEMBLY INSTRUCTIONS
1) Nokia X3 disassembly. 2) For disassembling you need the Nokia Standard
Tool kit version 2 plus the camera removal tool SS-
88. You will also need a DC and an AV plug.
3) Slide the phone open and release the battery
cover.
4) Remove the battery cover. If there is a battery
inserted, remove it also.
4) Unscrew the two TORX+ size 6 screws in the order
shown. Do not use them again. Discard them.
6) Use the SRT-6 to release the NUMERIC KEYMAT
ASSY and the E-COVER ASSY.

Nokia X3
RM-540
Service Manual Level 1&2
13 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
7) Remove the NUMERIC KEYMAT ASSY and the E-
COVER ASSY as shown.
8) Then separate the NUMERIC KEYMAT ASSY from
the E-COVER ASSY. The NUMERIC KEYMAT ASSY must
always be renewed.
9) Unscrew the four TORX+ size 6 screws in the
order shown. Do not use them again. Discard them.
10) Before removing the D-COVER ASSY, open the
USB DOOR.
11) Release the D-COVER ASSY as shown. 12) Use the SS-93 to carefully lift up the board to
board connector SHIELD LID. The board to board
connector SHIELD LID has to be always renewed.

Nokia X3
RM-540
Service Manual Level 1&2
14 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
13) Turn over the engine board. 14) Disconnect the UI FLEX connector with the SS-93.
Be careful not to damage the connector or any
nearby components.
15) The engine board and the SLIDE MODULE can be
now separated.
16) Use the tweezers to peel off the SPEAKER MESH.
Detach the corner of the DOMESHEET with the dental
tool and then peel off the DOMESHEET. Be aware of
the sharp point of the dental tool - be careful not to
injure yourself.
Do not use the SPEAKER MESH and DOMESHEET again.
17) Use the camera removal tool SS-88 to detach
the CAMERA.
18) Pull out the USB DOOR.

Nokia X3
RM-540
Service Manual Level 1&2
15 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
19) Use the tweezers to carefully release the clip
holding the SPEAKER OUTL TRIM TOP ASSY.
20) Detach the SPEAKER OUTL TRIM TOP ASSY.
21) Lift up the AV jack with an AV plug and remove
the AV jack with the tweezers.
22) Release the DC jack with a DC plug. Use the
tweezers to remove the DC jack.
23) Lift up the IHF SPEAKER with the dental tool and
remove the speaker with the tweezers.
24) Remove the SPEAKER ADHESIVE with the
tweezers. Do not use the adhesive again. Discard it.

Nokia X3
RM-540
Service Manual Level 1&2
16 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
25) Use the SS-93 to release the ANTENNA MODULE.
Press the ANTENNA MODULE lightly through the D-
COVER.
26) Lift up the IHF SPEAKER with the dental tool and
remove the speaker with the tweezers. Remove the
SPEAKER ADHESIVE with the tweezers. Do not use
the adhesive again. Discard it.
27) Use the dental tool to carefully lift up the
MICROPHONE.
28) Make sure the slide is positioned as shown in
the picture. Unscrew the two TORX+ size 5 screws in
the order shown. Do not use them again. Discard
them.
29) Insert the SRT-6 between the A-COVER ASSY, and
the SLIDE MODULE ASSEMBLY. Slide the SRT-6 along
the edges to release the clips holding the A-COVER
ASSY.
30) Make sure all the clips are released.

Nokia X3
RM-540
Service Manual Level 1&2
17 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
31) Remove the SLIDE MODULE ASSEMBLY in the
direction shown.
32) Protect the LCD with protective film.
33) Use the SS-93 to open the LCD CONNECTOR. While
opening the connector be careful not to damage it.
34) Use the dental tool to slightly lift up the LCD. Be
very careful not to break the LCD!
35) Use the SS-93 to loosen the adhesive
underneath the LCD. Then lift up the LCD.
36) Use the sharp end of the SS-93 to release the
EARPIECE. Remove the EARPIECE with the tweezers.

Nokia X3
RM-540
Service Manual Level 1&2
18 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
37) Separate the FUNCTION KEYMAT ASSY from the A-
COVER ASSY.
38) Nokia X6 disassembly is now complete.
- END OF DISASSEMBLY-

Nokia X3
RM-540
Service Manual Level 1&2
19 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
11. ASSEMBLY HINTS
1) Tighten the two TORX+ size 5 screws to the
torque of 20 Ncm in the order shown.
2) Tighten the four TORX+ size 6 screws to the
torque of 12 Ncm in the order shown.
3) Tighten the two TORX+ size 6 screws to the
torque of 18 Ncm in the order shown.

Nokia X3
RM-540
Service Manual Level 1&2
20 Confidential
| Copyright © 2009 Nokia | All rights reserved
Version 1.0
12. SOLDER COMPONENTS
X6052
X6001
X6053
V2502
V2501
V2500
V2503
S2502 S2501 S2503 X2913
X2912 X2910
Ver. 1.0
TOP
BOTTOM
Other manuals for X3
5
Table of contents
Other Nokia Cell Phone manuals

Nokia
Nokia 2710 User manual

Nokia
Nokia 9300 - Smartphone 80 MB Assembly Instructions

Nokia
Nokia N Series User manual

Nokia
Nokia Lumia User manual

Nokia
Nokia N86 User manual

Nokia
Nokia C6-00 User manual

Nokia
Nokia N93i Quick start guide

Nokia
Nokia C2-01 User manual

Nokia
Nokia G20 User manual

Nokia
Nokia 9357715 User manual

Nokia
Nokia X2-01 User manual

Nokia
Nokia 3610 User manual

Nokia
Nokia 6275 User manual

Nokia
Nokia 6030 - Cell Phone - GSM User manual

Nokia
Nokia C2-00 User manual

Nokia
Nokia 2280 User manual

Nokia
Nokia 6288 - Cell Phone - WCDMA User manual

Nokia
Nokia 210 Dual SIM User manual

Nokia
Nokia C2-00 User manual

Nokia
Nokia NSD-1 SERIES Installation instructions