Nordson nLighten User manual

Encore, Nordson, and the Nordson logo are registered trademarks of the Nordson Corporation.
nLighten is a trademark of Nordson Corporation.
nLighten™
Sheet 1 of 2
Use only 1.5 V, size “AA”, IEC-LR6 Alkaline batteries.
Replace all batteries at the same time.
Do not mix batteries from different manufacturers, new
with used, or different specifications. Improper battery
installation can cause batteries to explode or leak and
cause personal injury. Observe the polarity during
installation (see step 5 for reference). Do notInstallation
recharge primary batteries.
1. Remove spray gun from a hazardous area.
2. Clean the assembly of any coating material
before changing the batteries.
3. Unscrew the battery caps with a flat blade
screwdriver.
4. Remove old batteries and dispose of them
properly.
5. Install the new batteries, inserting the negative
terminal into the housing first (see Installation
illustration, step 5).
6. Install and tighten the battery caps until the
cap bottoms against the housing. Do not
over-tighten.
Battery Disposal
Dispose of all spent batteries according to all local
rules and regulations.
WARNING: Do not open to change batteries
in powder booth or other hazardous areas.
Installation Safety Operations
Read and follow any safety instructions stated in this
document. Failure to do so may result in damage to
equipment or injury to operator. Task and equipment
specific warnings, cautions, and instructions are
included in this document where appropriate.
Refer to the Safety Section of the manual for the
Encore Manual Powder Spray System or Spray Gun
®
for additional safety information. These can be found
by scanning the QR code above or going to
emanuals.nordson.com
1
2
WARNING: LED Radiation (RG-2)
Do not stare into the beam of light, may be
harmful to eyes.
3
4
Remove
existing
hook
Install new
bracket and
hardware
Attach light to
bracket
Install new
hook
Battery Installation/Removal
For Assistance, Call Customer Service at 800-433-9319
(assemble lanyard to cap as in detail)
Install batteries,
battery caps and lanyard
+
-
5
Application Mode - 33 lumens, max
Squeeze the trigger when ready to spray powder.
nLighten will automatically turn on and remain on
while spraying powder.
LED output will track the KV output of the multiplier.
Inspection Mode - 65 lumens
Release the trigger when ready to stop spraying
powder. nLighten will remain on for fifteen seconds
and will automatically turn off. If more inspection time
is needed, quickly press and release the trigger to
receive an additional fifteen seconds of inspection
time.
Original Copyright Date: 2018
Issued: 09/2018
Part Number 1614474-01
Instruction Sheet
©2018 Nordson Corporation

Encore, Nordson, and the Nordson logo are registered trademarks of the Nordson Corporation.
nLighten is a trademark of Nordson Corporation.
nLighten™
Sheet 2 of 2
For Assistance, Call Customer Service at 800-433-9319
Specific Conditions of Use:
Specifications
Primary Cell Type:
Recommended Cell Manufacturers:
Ambient Temperature Rating:
Maximum Relative Humidity
Hazardous Location Rating for Light:
Dust Ingress Protection:
Only use (2) 1.5 V “AA” Alkaline
(ANSI-15A, IEC-LR6) batteries
Energizer EN91 Alkaline
+15 to +40 C (59 to 104 F)
°°
95% non-Condensing
For Electrostatic Finishing Applications
using Class Spray MaterialsII
IP6X
Troubleshooting
NOTE: There are no serviceable components within the housing assembly.
ISSUE RESOLUTION
No light when trigger is
released
Replace batteries.
Verify proper battery orientation.
Low light when trigger is
depressed
Housing not in alignment with spray gun body -
realign housing to spray gun body.
Lens cover obstructed with powder - clean lens
with isopropyl alcohol.
No light when trigger is
depressed
Housing not in alignment with spray gun body -
Realign housing to spray gun body.
Damage to internal circuitry - replace unit.
ITEM
1
2
3
5
5a
6
7
8
9
10
PART NO.
1611977
-------
1613361
-------
DESCRIPTION
KIT, nLighten, LED, Encore
Housing Assembly
Cover, housing, nLighten, Encore
Battery
Cap Assembly, battery, nLighten, Encore
O-ring, silicone, 13.5 mm ID x 1.5 mm
Lanyard, nLighten, Encore
Hook, nLighten, Encore
Screw, pan head, M3 x 5 mm, zinc
Lock Washer, M3 internal tooth, zinc
Clip, spring, mount, LED, Encore
QTY.
1
1
2
2
2
1
1
2
2
1
4
1614040
KIT, service, nLighten
1
1
-------
-------
-------
-------
-------
-------
-------
Approvals: cFMus, FM18ATEX00061X
=The nLighten™ LED Kit shall only be used over the ambient temperature range of +15 C to +40 C with
OO
the manufacturer’s separately ATEX certified manual electrostatic powder applicators.
=The equipment can only be used in areas of low impact risk.
=Caution should be taken when cleaning plastic surfaces on the nLighten LED. There is a potential for
static electricity buildup on these components.
=For use with Encore LT manual applicator FM11ATEX0056X, and Encore XT/HD applicators
FM14ATEX0051X
Parts
23
4
5a
5
6
7
8
9
110
Original Copyright Date: 2018
Issued: 09/2018
Part Number 1614474-01
Instruction Sheet
©2018 Nordson Corporation

DOC14046-03
Product: Encore nLighten LED Kit
EU DECLARATION of CONFORMITY
This Declaration is issued under the sole responsibility of the manufacture.
Models:
Encore nLighten
Description:
The LED light kit is for use with Nordson Encore Manual Spray Applicators
Applicable Directives:
2014/30/EU - EMC Directive
2014/34/EU - ATEX Directive
Standard Used for Compliance:
EN/ISO12100 (2010) EN60204-1 (2016) EN61000-6-3 (2007) FM 7260 (2018)
EN60079-0 (2018)
EN50050-2 (2013) EN61000-6-2 (2005)
EN60079-31 (2014) EN60079-28 (2015) EN55011 (2009)
Ratings:
-Ambient Temperature: +15OC to +40OC
-Ex II 2 D
ATEX Product Certificate: ATEX Quality System Certificate:
-FM18ATEX0061X (Norwood, Mass. USA) -1180 Baseefa (Buxton, Derbyshire, UK)
Nordson Authorized Representative in the EU
Person authorized to compile the relevant technical
documentation. Contact:
Operations Manager
Industrial Coating Systems, Nordson Deutschland GmbH,
Heinrich-Hertz-Straße 42-44, D-40699 Erkath
Vance Wilson
Engineering Manager
Industrial Coating Systems
Amherst, Ohio, USA
Date: 24Aug2018
P/N: 1611977
CUS
APPROVED
For Electro. Fin. Appl.
CL.Spray Matl. II ,
WHEN CONFIGURED IN ACCORDANCE
WITH 1084547 OR 1107255
FM18ATEX0061X
II 2
1180
!
SEE INSTRUCTIONS 1614474
VOIR LES INSTRUCTIONS
Ex op is tb lllB T85C Db
D/C: AAXXY
D
Ta= +15 to +40C
555 JACKSON ST, AMHERST, OH USA