Nordyne Q4RD 060 User manual

Installation Instructions
Single Package Heat Pump
These instructions are primarily intended to assist qualified individuals expe-
rienced in the proper installation of heating and/or air conditioning appliances.
Some local codes require licensed installation/service personnel for this type
equipment. All installations must be in accordance with these instructions and
with all applicable national and local codes and standards.
Read these instructions thoroughly before starting the installation. Follow all
precautions and warnings contained within these instructions and on the unit.
IMPORTANT
TM

2

3
It is the sole responsibility of the homeowner to
make certain that heat pump has been correctly
set up and adjusted to operate properly.
The Manufacturer warrants the heat pump to be
free from defects in material or workmanship for a
period of one year.We will not be responsible for
any costs found necessary to correct problems
due to improper setup, improper installation,
adjustments, improper operating procedure on
the part of the user, etc.
Some specific examples of service calls which
are not included in the limited warranty are:
1. Correcting wiring problems in the electrical
circuit supplying the heat pump.
SECTION 1. OWNER INFORMATION
WINTER HEATING
1. Outdoor air enters the heat pump.
2. The cold, heat-transfer section (outdoor coil)
extracts the heat from the air as the refrigerant
evaporates from a liquid to a cold gas.
3. The refrigerant, compressed to a hot gas by
the heat pump, carries the heat to the heat-
transfer section (indoor coil).
4. The hot, heat-transfer section (indoor
coil) releases the heat as the refrigerant
condenses from a gas to a liquid.
5. The blower circulates the heat throughout
the home via the supply duct.
6. The refrigerant returns to the outdoor coil
and evaporates once again to absorb more
heat.
SUMMER COOLING
1. Indoor air enters the return air duct.
2. The cold, heat-transfer section (indoor coil)
extracts the heat from the air as the refrigerant
evaporates from a liquid to a cold gas.
3. The refrigerant, drawn to the heat pump and
compressed to a hot gas, carries the heat
outdoors.
4. The hot, heat-transfer section (outdoor coil)
releases the heat as the refrigerant condenses
from a gas to a liquid.
5. The heat pump (outdoor fan) discharges the
heat to the outside air.
6. The refrigerant returns to the indoor coil
and evaporates once again to absorb more
heat.
5
4
1
2
3
6
2
1
53
6
4
2. Resetting circuit breakers or other switches.
3. Adjusting or calibrating of thermostat.
To avoid misunderstandings at a later date,
carefully review these responsibilities with your
dealer or service company.
The heat pump system will heat and cool your
home and save your energy dollars.
During the summer, a heat pump cools a house
by absorbing heat from within the house and
exhausting it outdoors. During the winter, a heat
pump heats a house by absorbing heat outdoors
and exhausting it indoors. This is an efficient
heating means because you pay for “moving”
heat from outdoors to indoors, but do not pay
to generate the heat.

4
OPERATING INSTRUCTIONS
To Operate Your Heat Pump For Cooling —
1. Set the thermostat system switch to COOL
and the thermostat fan switch to AUTO. See
Figure 1.
2. Set the thermostat temperature selector to the
desired cooling temperature.The outdoor unit
fan, the indoor blower, and the compressor
will all cycle on and off to maintain the indoor
temperature at the desired cooling level.
NOTE: If the thermostat temperature level is
re-adjusted, or if the thermostat system switch
is re-positioned, the outdoor unit fan and the
compressor may not start immediately. A
protective timer circuit holds the compressor and
the outdoor fan off for approximately six minutes
following a previous operation or the interruption
of the main electric power
To Operate Your Heat Pump For Heating —
1. Set the thermostat system switch for HEAT
and the thermostat fan switch to AUTO. See
Figure 1.
2. Set the thermostat temperature selector to the
desired heating temperature.The outdoor unit
fan, the indoor blower, and the compressor
will all cycle on and off to maintain the indoor
temperature at the desired heating level.
NOTE: If the thermostat temperature level is
re-adjusted, or if the thermostat system switch
is re-positioned, the outdoor unit fan and the
compressor may not start immediately. A
protective timer circuit holds the compressor and
the outdoor fan off for approximately six minutes
following a previous operation or the interruption
of the main electrical power.
Emergency Heat — Some thermostats will
include a system switch position termed EM
HT or AUX HT, etc. This is a back-up heating
mode to be used only if there is a suspected
problem. With the system switch set to EM
HT, etc., the compressor and outdoor fan will
be locked off and supplemental heat (electric
resistance heating) will be used as a source of
heat.Sustained use of electric resistance heat in
place of the heat pump will result in an increase
in electric utility costs.
Defrost— During cold weather heatingoperation,
the outdoor unit will develop a coating of snow
and ice on the heat transfer coil. This is normal
and the unit will periodically defrost itself.During
the defrost cycle, the outdoor fan will stop, while
the compressor continues to run and heat the
outdoor coil, causing the snow and ice to melt.
During defrost, there may be some steam rise
from the outdoor unit as the warm coil causes
some melted frost to evaporate.
Figure 2. Thermostat Interlock System
Cooling
Thermostat Furnace
Thermostat
Double Throw
Double Pole Switch
To Air Conditioner To Furnace
RR
Figure 1. Typical Thermostat
FAN SWITCH
TEMPERATURE SELECTOR

5
SPECIFICATIONS
Single Package Heat Pumps are designed for
outdoor rooftop or ground level slab installations.
The units are shipped ready for horizontal duct
connections and are easily converted for down
flow applications.
All Q4RD models are shipped from the factory
with the following:
1. Zero clearance to combustibles
2. Multi-speed direct-drive blower.
3. Compressor Anti-short-cycle timer for single
phase models.
4. Blower Speed Relay.
5. Horizontal or Down flow duct connections.
6. Square-to-round adapter boxes with 14”
collars for supply and return openings.
The unit dimensions are shown in Figure 3.
WARNING:
The square-to-round adapter boxes
and 14” collars are shipped inside the
return inlet. These must be removed
before the unit is run.
Optional field-installed electric heater kits are
available in 5 kw through 20 kw heating capacities.
A separate installation instruction document
for the electric heaters and their application
accompanies this one. A two stage heat 24VAC
thermostat should be used with electric heater
kits installed.
SAFETY CONSIDERATIONS
It is the responsibility of the installer to ensure
that the installation is made in accordance with
all applicable local and national codes.
WARNING:
Improper installation, service,
adjustment,or maintenance may cause
explosion,fire,electrical shock or other
hazardous conditions which may result
in personal injury or property damage.
Unless otherwise noted in these
instructions, only factory authorized
kits or accessories may be used with
this product. Noncompliance may void
the unit’s warranty.
Labels, Tags — When working with this
equipment, follow all precautions in the literature,
on tags, and on labels provided with the unit
and/or approved field installed kits. The type
of hazard and severity are described on each
label or tag.
Pressures Within The System — This
equipment contains liquid and gaseous
refrigerant under high pressure. Installation or
servicing should only be performed by qualified
trained personnel thoroughly familiar with this
type equipment.
INSTALLATION REQUIREMENTS
Equipment Check — Before beginning the
installation, verify that the unit model is correct for
the job. The unit model number is printed on the
data label.All units have been securely packaged
at the point of shipment.After unpacking the unit,
carefully inspect it for apparent and concealed
damage.Claims for damage should be filed with
the carrier by the consignee.
Requirements and Codes — The installer
must comply with all local codes and regulations
which govern this type equipment. Local codes
and regulations take precedence over any
recommendationscontained inthese instructions.
All electrical wiring must be made in accordance
with local codes and regulations and with the
National Electric Code (ANSI/NFPA 70) or in
Canada the Canadian Electric Code Part 1 CSA
C.22.1.Air Ducts must be installed in accordance
with the standards of the National Fire Protection
Association “Standards for Installation of Air
Conditioning and Ventilation Systems” (NFPA
90A), “Standard for Installation of Residence
Type Warm Air Heating and Air Conditioning
Systems” (NFPA 90B), these instructions and
all applicable local codes.
NFPA publications are available by writing:
National Fire Protection Association
Batterymarch Park
Quincy, Maine 02269
IMPORTANT: Do Not Place Unit Under The
Home.
Unit Location — This heat pump is designed only
for outdoor installations.Choosing the location of
the unit should be based on minimizing the length

6
Top View
Side View Back View
24.9
13.5
16.0
12.0
13.3
13.5
16.0
12.0
CG
A
47.5
3/4" NPT Female
Drain Connector
B
DOWNFLOW
SUPPLY DUCT
OPENING
DOWNFLOW
RETURN DUCT
OPENING
23.5
1.25 Ø Power Entry
1.75 Ø Power Entry (Capped)
0.88 Ø Control Wiring Entry
23.6
27.2
30
1.8
4.00
13.5
16.0
14.7
13.5
16.0
13.45
11.75 22.75 55.8
C
SUPPLY RETURN
4.0
CONDENSING
COIL
5.0
8
Figure 3. Dimensions
Model Number
Q4RD
Unit
Weight
Center of Gravity Height (in inches)
AB
C
with base rails without base rails
060 580 29.5 26.0 43.0 39.3

7
Condensate Drain
Figure 5. Condensate Drain
Figure 4. Minimum Clearances
located on the front side of the unit. See Figure
5. Install a 2 inch condensate trap in the drain
line of the same size and prime with water.When
connecting rigid drain line, hold the female fitting
with a wrench to prevent twisting. Do not over
tighten! Refer to local codes and restrictions for
proper condensate disposal requirements.
UNIT INSTALLATION
Ground Level — When installing the unit at
ground level, provide a concrete mounting pad
separate from the building foundation. The
pad must be level to insure proper condensate
disposal and strong enough to support the unit’s
weight. Refer to Figure 3. Make sure the slab
is a minimum of 2” above the grade and in an
area that drains well. See Figure 6.
AIR DUCTS
This unit is designed only for use with a supply
and return duct. Air ducts should be installed in
accordance with the standards of the National
Fire Protection Association “Standard for
Installation of Air Conditioning Systems” (NFPA
90A),“Standard for Installation of ResidenceType
Warm Air Heating and Air Conditioning Systems”
(NFPA 90B), and all applicable local codes.
of the supply and return ducts. Consideration
should also be given to availability of electric
power, service access, noise, and shade. Suf-
ficient clearance for unobstructed airflow through
the outdoor coil must be maintained in order to
achieve rated performance See Figure 4 for
minimum clearances to obstructions.
Air Filters — A suitable air filter must be installed
in the return air system. Air filter pressure drop
must not exceed 0.08 inches w.c. at 300 fpm.
Condensate Drain — Condensate is removed
from the unit through the 3/4” female pipe fitting
36"
36"
0"
36"
72"

8
Design the duct work according to methods
described by the National Warm Air Heating
and Air Conditioning Association (ACCA). The
ducts must be properly sized not to exceed .2”
w.c. pressure drop at 400 scfm per nominal ton
of cooling capacity.
Duct work should be attached directly to the unit
flanges for horizontal applications.
Installation of Square-to-Round Adapters
— The square-to-round adapter panel and 14”
round collars must be removed from the return
inlet opening.
1) Remove the close-off plates from the supply
and return openings.
2) Fit the 14” collar inside the adapter plate
and secure.
3) Place the square-to-round adapter plate,
one over each opening, and attach with
sheet metal screws.
4) Seal around the adapter box and collars.
Refer to Figure 7 for installation.
Unconditioned Spaces — All duct work passing
through unconditioned space must be properly
insulated to minimize duct losses and prevent
condensation.Use insulation with an outer vapor
barrier.Refer to local codes for insulation material
requirements.
Acoustical Duct Work — Certain installations
may require the use of acoustical lining inside
the supply duct work. Acoustical insulation must
be in accordance with the current revision of the
Sheet Metal and Air Conditioning Contractors
National Association (SMACNA) application
standard for duct liners. Duct lining must be UL
classified batts or blankets with a fire hazard
classification of FHC-25/50 or less. Fiber duct
work may be used in place of internal duct liners
if the fiber duct work is in accordance with the
current revision of the SMACNA construction
standard on fibrous glass ducts. Fibrous duct
work and internal acoustical lining must be NFPA
Class 1 air ducts when tested per UL Standard
181 for Class 1 ducts.
Horizontal to Down flow Conversion — The unit
is shipped ready for horizontal duct connections.
If down flow ducts are required, the unit must be
converted following the steps below for both the
supply and return ducts.
1) Locate the duct cap inside the duct openings
and remove the screw holding it in place.
2) Lift the cap out of the unit. (The cap can
be pushed up from the bottom by reaching
through the fork slot).
3) Cover the horizontal duct opening with the
cap. The insulation will be on the indoor
side.
4) Fasten the cover with screws and seal to
prevent air leakage.
Clearance — These units are approved for 0
inch clearance.
Locating and Installing the Return
Air Assembly
To avoid complications, locate and install the
return air assembly first. The return air box with
grille and filter (Figure 8) should not be located
in heavy traffic areas like hallways or center of
rooms.A good spot is in a corner or under a table,
2"
Figure 6. Ground Level Installation Figure 7. Supply and Return Duct Fittings

9
if a minimum two inch clearance is available. If
desired, the return opening can be located inside
a closet with louvered doors that have an open
area equal to or greater than the return grille.
The return air grille can be placed in the wall
of a closet and the air ducted into the filter box
through a boxed-in area at the closet floor level.
Make sure the filter is readily accessible.
After determining the location of the return air
opening, start the installation from under the home
by cutting a small hole in the fiber underboard to
determine how the floor joist location will affect
cutting the opening needed for the box. Floor
joists generally are located on 16” centers, leav-
ing 14-3/8” between joists. After measuring the
return air box, cut the hole through the floor so
that the box will fit between the floor joists. Care
should be taken when cutting through carpeting
to avoid snags. In most installations it will be
necessary to cut a similar hole in the fiberboard
directly under the hole in the floor. However, if
the floor is more than ten inches deep, it will only
be necessary to cut a hole for the collar on the
return air box or for the insulated duct.
Set the box into the opening and fasten with
screws or nails. Put the filter and return air
grille in place.
Note: For highly resistive duct systems it may be
necessary to add an additional return air duct to
achieve maximum performance.
Locating and Installing the Supply
Damper(s)
When locating the supply damper(s), carefully
check floor joists and frame members that could
interfere with the installation of the damper or
flexible duct. Ideally, the damper should be
located in the bottom of the main duct, forward
of center of the home, at least three feet from
the nearest register. The round supply opening
in the slanted side of the damper should face
the side of the home where the heat pump is
located. To locate the center of the heat duct,
first cut a small hole in the fiberboard below the
duct at the desired location. After locating the
duct center, cut a hole approximately 3/4” larger
than the damper opening in the fiberboard. Cut
a 9-1/8” x 13-1/8” hole in the duct and bend over
all tabs flat on the inside of the heat duct. After
inserting the damper into the duct, bend over
all tabs flat on the inside of the heat duct. Seal
the opening between the fiberboard and damper
or flexible duct.
DUCTING SYSTEM
Duct Requirements
The supply duct system, including the number
and type of registers, will have much more ef-
fect on the performance the system than any
other factor. The duct must be sufficiently large
to conduct an adequate amount of air to each
register.
THE HEAT PUMP SYSTEM WILL NOT COOL
OR HEAT THE HOME IF THE AIR IS LOST
TO THE OUTSIDE THROUGH LEAKS IN THE
DUCT SYSTEM. ALSO, DUCTS WHICH ARE
COLLAPSED OR RESTRICTED BY FOREIGN
OBJECTS WILL PREVENT ADEQUATE AIR
FLOW.
Figure 9. Supply Damper
AUTOMATIC DAMPER IS CLOSED
WHEN HEAT PUMP IS OFF
Figure 8. Return Air Box

10
Connecting the Return and Supply
Air Flexible Ducts
a. The return and supply duct openings for all
units is 14” in diameter.
b. The flexible ducts can be connected to
the corresponding fittings with the clamps
provided with the ducts. Note: All connections
should be leak tight or a loss in cooling
capacity will result.
c. The flexible ducts may be cut to the required
length, see instructions packed with duct.
Keep all ducts as short and straight as
possible. Avoid sharp bends.
d. Ducts may be spliced with sheet metal
sleeves and clamps.(See Ducting Installation
Accessories below.)
e. Once the inner duct is connected to the
proper fitting, the insulation and plastic sleeve
should be pulled over the connection and
clamped.
f. For homes with multiple supply ducts or for
special applications, a Y fitting is available
to divide the supply air so it can be ducted
to different areas of the home for more
efficient cooling. Note: The Y fitting should
be insulated for maximum performance.
ELECTRICAL WIRING
General — Electrical power wiring must be made
in accordance with all applicable local codes and
ordinances, and with the current revision of the
National Electric Code NFPA 70 or in Canada
CSA C.22.1 - Canadian Electrical Code Part 1.
5
5
4
4
5
2
3
1
5
2
35
4
1
7
Figure 10. Typical Applications
Ref. No. Description
112” x 20” Return Air
216” x 20” Air Filter
312” x 20” Grille
4Supply Damper
514” Diameter Flex Return Duct
6“Y” Fitting
TYPICAL APPLICATIONS
MULTIPLE DUCT APPLICATION
SINGLE DUCT APPLICATION

11
If any of the original wire as supplied with the
unit must be replaced, it must be replaced with
material of the same gage and temperature
rating.
WARNING:
To avoid the risk of electrical shock,
personal injury, or death, disconnect
all electrical power to the unit before
performing any maintenance or
service.The unit may have more than
one electrical power supply.
Line Voltage — Before proceeding with the
electrical connections, make certain that the
voltage, frequency, and phase of the supply
source are the same as those specified on the unit
rating plate. Also verify that the service provided
by the utility is sufficient to handle the additional
load imposed by this equipment.
See the unit wiring label for proper high and low
voltage wiring. Make all electrical connections
in accordance with all applicable codes and
ordinances.
Use a separate branch electrical circuit for this
unit. A means of electrical disconnect must be
located within sight of and readily accessibility
to the unit. Internally mounted circuit breakers
are available as field installed options. These
circuit breakers can be used as an electrical
disconnect.
The unit is shipped from the factory wired for 240
volt transformer operation.For 208 volt operation,
remove the lead from the transformer terminal
marked 240V and connect it to the terminal
marked 208V. For maximum ampacity and over
current protection, see the unit rating plate.
Provide power supply (or supplies) for the unit in
accordance with the unit wiring diagram, and the
unit rating plate. Connect the line-voltage leads
to the corresponding terminals on the contactor
(or the circuit breaker when the field installed
circuit breaker kits are used) inside the control
compartment. Use only copper wire for the line
voltage power supply to this unit.Use proper code
agency listed conduit and a conduit connector
for connecting the supply wires to the unit and
for obtaining proper grounding. Grounding may
also be accomplished by using the grounding
lug provided in the control box.
WARNING:
The unit cabinet must have and
uninterrupted or unbroken electrical
ground to minimize personal injury if
an electrical fault should occur. This
ground may consist of electrical wire
or approved conduit when installed in
accordance with existing national or
local codes.
Blower Speed — For optimum system
performance and comfort, it may be necessary
to change the factory set speed. To change the
blower speed:
1. Disconnect all electrical power to the unit
and remove the blower panel.
2. Locate the orange and red wires
terminated to the blower motor. The
orange wire controls cooling operation
while the red wire controls heating
operation.
3. Verify the required speed from the airflow
data found in table 3. Place appropriate
wire on the appropriate motor speed tap
for the required airflow point.
NOTE: If the same speed is required for both
heating and cooling. Obtain the jumper wire
from the homeowners packet and connect it
to the blower relays at the NO & NC terminals.
Be sure to only connect the speed necessary
to one side of the jumper wire.
CAUTION:
To avoid personal injury or property
damage, make certain that the motor
leads cannot come into contact with
any uninsulated metal components
of the unit.
Check all factory wiring per the unit wiring
diagram and inspect the factory wiring connec-
tions to be sure none loosened during shipping
or installation.
Low Voltage Connections
Room Thermostat — Several options are
available for a room thermostat depending on

12
the accessories installed with the unit. Select a
thermostat which operates in conjunction with
the installed accessories.The thermostat should
be mounted about five feet above the ground on
an inside wall. The thermostat should be kept
away from drafts, slamming doors, lamps, direct
sunlight, or in line with the supply air flow.
To install the thermostat:
1. Position the sub base on an inside wall and
mark the mounting holes and thermostat
cable openings.
2. Cut out the cable opening and route the
thermostat cable from the unit’s low voltage
compartment to the thermostat location.
The thermostat cable is supplied by the
installer.
3. Connect the cable leads to the sub base
or thermostat terminals and to the unit’s
low voltage pigtails as shown in Figure 10.
A system wiring diagram is also provided
on the inside of the control panel cover.
4. Secure sub base or thermostat to the
wall using screws provided with the
thermostat.
5. If sub base is used, install the correct
thermostat housing to sub base.
6. Refer to thermostat instruction sheet for
complete detailed mounting information.
Defrost Cycle Timer — The defrost cycle timer
controls the time interval of the hot gas defrost
after the defrost sensor closes. It is located in
the lower left corner of the defrost control board
on the low voltage side of the control box.Three
interval settings are available: 30 minutes, 60
minutes, and 90 minutes.Time setting selection
is dependent on the climate where the unit is
being installed.
Example 1.Dry climate of Southern Arizona.
A 90 minute setting is recommended.
Example 2. Moist climate of Seattle,
Washington. A 30 minute setting is
recommended.
To set the cycle timer, place the timing pin on
the defrost control board to the desired time
interval post.
Note: All units are shipped from the factory with
the default time setting of 30 minutes.
Field Installed Electric Heat — These Single
Package Heat Pumps are designed to allow
optional electric heat to be field installed as
required by the building’s particular heating load.
The options available for each unit are shown in
the heater kit installation instructions. As noted
in the instructions, a field installed circuit breaker
kit is available as a means of electrical discon-
nect for the unit.
Install the heater kits as directed by the installation
instructions that come as part of the heater kit.
Follow all cautions and warnings as directed.
START UP AND SYSTEM CHECK
Pre-Start Check List
• Verify that the unit is level to allow proper
condensate drainage.
• Verify that there is free airflow to and from
the outdoor coil and that all clearance
requirements are met.
• Verify that the duct work is sealed to prevent
air leakage.
• Verify that the line voltage power leads are
securely connected and the unit is properly
grounded.
Figure 11. Motor Lead Connector
PIN NUMBER MOTOR SPEED WIRE COLOR
1LOW RED
2
4HIGH BLACK
3MEDIUM BLUE
5N/A N/A
6COMMON WHITE
1
2
4
3
5
6
RED
BLACK
BLUE
WHITE

13
• Verify that the low voltage wires are securely
connected to the correct leads on the low
voltage terminal strip.
• Verify that all exterior panels are replaced
and securely fastened.
• Verify that the outdoor fan turns freely.
• Verify that the power supply branch circuit
overcurrent protection is sized properly.
• Verify that the thermostat is wired correctly.
The thermostat function switch should be
set to “Off’ and the thermostat fan switch
should be set to “Auto.”
Start-Up Procedure
Close all electrical disconnects to energize the
system.
WARNING:
If the unit is equipped with a crankcase
heater, allow 24 hours prior to
continuing the start up procedures
to allow for heating of the refrigerant
compressor crankcase. Failure to
comply may result in damage and
could cause premature failure of
the system. This warning should be
followed at initial start up and any
time the power has been removed for
12 hours or longer.
Air Circulation — Leave the thermostat system
switch set to “Off” and set the thermostat fan
switch to “On.” The blower motor should run
continuously. Check for air delivery at the
register(s).Ensure that there are no obstructions
at the registers or in the duct work.Set thermostat
fan switch to “Auto.”
Short Cycle Protection — With the system
operating in cooling mode, note the temperature
setting of the thermostat and gradually raise the
set-point temperature until the unit de-energizes.
Immediately lower the set point temperature of
the thermostat to its original setting and verify
that the indoor blower is energized. Verify that
after approximately 5 minutes the compressor
and fan energize and that the temperature
of the discharge air is cooler than the room
temperature. This is available only for the single
phase models.
System Cooling
1. Set the thermostat system switch to “Cool”
and the thermostat fan switch to “Auto”.
Gradually lower the thermostat temperature
switch below room temperature and
observe that the blower, compressor, and
fan energize. Check that air cooler than
room temperature is being discharged
at the register. Listen for any unusual
noises.
2. After allowing the unit to run for several
minutes, set the temperature selector
above room temperature.
- The fan and compressor cycles off with
the thermostat.
- The blower should also stop unless fan
switch is set to “ON” position.
System Heating — If the unit has been equipped
with optional electric heater kits, set the system
thermostat switch to HEAT and set the thermostat
fan switch to AUTO. Verify that the compressor
and outdoor fan are not energized but that the
blower and heaters are. Check for warm air at
the supply registers.
UNIT MAINTENANCE
WARNING:
To avoid risk of electrical shock,
personal injury, or death, disconnect
all electrical power to the unit before
performing any maintenance or
service.The unit may have more than
one electrical supply.
Refrigerant Charging — Packaged heat
pumps are fully charged at the factory . The
system refrigerant charge can be checked and
adjusted through the service ports provided
in the front panel. Use only gauge lines which
have a “Schrader” depression device present
to actuate the valve. Draw a vacuum on gauge
lines to remove air before attaching them to the
service ports on the unit. Refrigerant charging
must be done by qualified personnel familiar with
safe and environmentally responsible refrigerant
handling procedures.

14
WARNING:
Single Packaged Heat Pumps are
shipped fully charged and ready for
installation.When a system is installed
according to these instructions, no
refrigerant charging is required.
If repairs make it necessary for
evacuation and charging, it should
only be done by qualified, trained
personnel thoroughly familiar with this
equipment. Some local codes require
licensed installation/service personnel
to service this type of equipment.
Under no circumstances should the
owner attempt to install and/or service
this equipment.Failure to comply with
this warning could result in property
damage, personal injury, or death.
CAUTION:
Use care when removing parts from
this unit. Personal injury can result
from sharp metal edges present
in all equipment of sheet metal
construction.
Routine Maintenance — Proper maintenance is
important to achieve optimum performance from
the heat pump. The ability to properly perform
maintenance on this equipment requires certain
mechanical skills and tools.If you do not possess
these skills, contact your dealer for maintenance.
Consult your local dealer about the availability of
maintenance contracts. At a minimum, routine
maintenance should include the following:
1. Inspect and clean or replace air filters at
the beginning of each heating and cooling
season, or more frequently if required.
2. Inspect the condensate drain and outdoor
coil at the beginning of each cooling season.
Remove any debris.Clean the outdoor coil
and louvers as necessary using a mild
detergent and water.Rinse thoroughly with
water.
3. Inspect the electrical connections for
tightness at the beginning of each
heating and cooling season. Service as
necessary.
CAUTION:
The unit should never be operated
without a filter in the return air system.
Replace disposable filters with the
same type and size.
4. The motors for the circulating air blower
and the outdoor fan are pre-lubricated at
the factory. No further oiling is required for
the life of this product.
Table 1. Blower Curves
* Denotes factory set cooling and heat pump speed
** Denotes factory set electric heating speed
Model Number
External Static Pressure
Drop - inches water column
Q4RD 0.1 0.2 0.3 0.4 0.5 0.6
060
Tap T1 1515 1450 1380 1350 1300 1250
Tap T2 1580 1520 1460 1400 1360 1300
Tap T3 1740 1690 1650 1600 1540 1500
Tap T4 1960 1910 1840 1820 1780 1740
Tap T5 2090 2050 2010 1975 1940 1900

15
E
O
G
R
Y1
1
2
3
4
5
6
7
8
9
Blue
ECONOMIZER
PLUG
INDOOR
THERMOSTAT
SUB-BASE
Green
FROM
BLOWER
RELAY
Y2
W2
C
DEFROST
BOARD
1
2
3
4
5
6
7
8
9
Brown
Orange
Accessory
Heat Plug
Typical Wiring (Field Supplied) for 1-Stage Cool, 1 Stage Electric Heat
Typical Wiring (Field Supplied) for 2-Stage Cool, 2-Stage Electric Heat
with an Optional Outdoor Thermostat
Figure 12. Typical Heat Pump Thermostat Connections
E
O
G
R
Y1
1
2
3
4
5
6
7
8
9
Blue
ECONOMIZER
PLUG
INDOOR
THERMOSTAT
SUB-BASE
Green
FROM
BLOWER
RELAY
Y2
W2
C
DEFROST
BOARD
1
2
3
4
5
6
7
8
9
Brown
Orange
Accessory
Heat Plug
Optional
Outdoor
Thermostat
(Field Supplied)
O

16
5 OUTDOOR TEMPERATURE (°F)
TON 70 75 8085 90 95 100 105
Suct.
Press.
Dis.
Press.
Dis.
Tem
p
.
Dis.
Press.
Dis.
Tem
p
.
Dis.
Press.
Dis.
Tem
p
.
Dis.
Press.
Dis.
Tem
p
.
Dis.
Press.
Dis.
Tem
p
.
Dis.
Press.
Dis.
Tem
p
.
Dis.
Press.
Dis.
Tem
p
.
Dis.
Press.
Dis.
Tem
p
.
67 154 140
69156 146 173 146
71 158 151 176 152 193 152
73 160 158 178 157 195 157 212 158
75 163 160 180 162 197 162 214 163 231 164
77 183 165 199 167 216 168 233 168 251 170
79203 170 219172 235 173 253 174 270 175
81 222 175 238 177 255 178 272 179289180
83 226 179242 181 258 182 274 183 291 184
85 245 185 261 186 278 187 293 188
87 265 190 281 192297193
89284 196 301 197
91 304 202
93
Table 2. 13 SEER Cooling Charging Charts
Cooling Charging Chart
* Note: All pressures are listed in psig. and all temperatures in deg. F.
— Shaded Boxes indicate flooded conditions
— Rated Design Values. Suction Pressure will be lower than design
value if indoor airflow, entering dry bulb, or entering wet bulb tem-
peratures are lower than design.
— Discharge temperatures greater than charted values indicates a
refrigerant undercharge.

17
¢7105753
¤
1. Disconnect all power before servicing. 2. For supply connections use copper conductors only. 3. Not suitable on systems that exceed 150 V to ground. 4. If any of the original wire as supplied with the furnace must be replaced, it must be replaced with wiring material having a temperature rating of at least 105°C. 5. For supply wire ampacities and overcurrent protection, see unit rating plate.
1. Couper le courant avant de faire letretien. 2. Employez uniquement des conducteurs en cuivre. 3. Ne convient pas aux installations de plus de 150 V
a la terre.
7105750
N
NOTES:
DEFROST BOARD OPERATION: CLOSES DURING DEFROST. RAITNG: 1 A MAXIMUM OPENS DURING DEFROST. RATING: 2 HP AT 230 VAC MAXIMUM CLOSED WHEN “Y” IS ENERGIZED. OPEN WHEN “Y” IS DEENERGIZED. PROVIDES “OFF” DELAY TIME OF 5 MIN WHEN “Y” IS DEENERGIZED. WITH DFT CLOSED AND “Y” ENERGIZED, COMPRESSOR RUN TIME IS ACCUMULATED. OPENING OF DFT DURING DEFROST OR INTERVAL PERIOD RESETS THE INTERVAL TO 0.
1 2 3 4
C
R
S
CHF
EDFTR W2 0 Y C T2 T1
DF2 DF1
CY0W2RE
PRESSURE
SWITCH
(IF EQUIPPED)
TO 208/230 VAC
POWER SUPPLY
BLOWER
MOTOR
T1
T3
T4
T2 G
N
L
C
2 3 4 5 6 7 8 9 1
2 3 4 5 6 7 8 9 1
2 3 4 5 6 7 8 9 1
2 3 4 5 6 7 8 9 1
8
7
6
5 4 3 2 1
9
8
7
6
5 4 3 2 1
9
T5
DEFROST
SENSOR
COMPRESSOR
CONTACTOR
OUTDOOR FAN
MOTOR
COMPRESSOR
DUAL CAPACITOR
HEATER
PLUG
REVERSING
VALVE
SOLENID
3 AMP
FUSE
DEFROST
CONTROL
BOARD
TO INDOOR THERMOSTAT
TO DISCHARGE
AIR SENSOR
BLOWER
RELAY
TRANSFORMER
C
R
S
L2 L1
T1T2
13 56 24
24V
COM
208V
240V
ECONOMIZER JUMPER
HARNESS ASSY
9-WIRE
GB
ECONOMIZER
PLUG
ECONOMIZER
PLUG
BROWN
WHITE
BLACK
RED BLUE
YELLOW
YELLOW
RED RED
BLUE
BLACK
GREEN
ORANGE
GREEN
GREY
GREEN
WHITE
WHITE WHITE
BLACK
BLUE
BLACK
BLACK
BLACK
BLACK
BLACK
ORANGE
WHITE
WHITE
RED
RED
RED
BROWN
YELLOW YELLOW
GREY
GREEN
BLUE
BLACK
YELLOW ORANGE
ORANGE
GREEN/YELLOW
BLUE
BROWN
RED RED
RED RED
RED
Legend
Field Wiring
Factory Wiring:
Low Voltage High Voltage
Note: See Installation
Instructions for wiring, application, and information concerning accessory Heat Kits and other options.
ORANGE
WD #7105750

18
WD #7105830
¢710583,
¤
1. Disconnect all power before servicing. 2. For supply connections use copper conductors only. 3. Not suitable on systems that exceed 150 V to ground. 4. If any of the original wire as supplied with the furnace must be replaced, it must be replaced with wiring material having a temperature rating of at least 105°C. 5. For supply wire ampacities and overcurrent protection, see unit rating plate.
1. Couper le courant avant de faire letretien. 2. Employez uniquement des conducteurs en cuivre. 3. Ne convient pas aux installations de plus de 150 V
a la terre.
7105830
NOTES:
DEFROST BOARD OPERATION: CLOSES DURING DEFROST. RAITNG: 1 A MAXIMUM OPENS DURING DEFROST. RATING: 2 HP AT 230 VAC MAXIMUM CLOSED WHEN “Y” IS ENERGIZED. OPEN WHEN “Y” IS DEENERGIZED. PROVIDES “OFF” DELAY TIME OF 5 MIN WHEN “Y” IS DEENERGIZED. WITH DFT CLOSED AND “Y” ENERGIZED, COMPRESSOR RUN TIME IS ACCUMULATED. OPENING OF DFT DURING DEFROST OR INTERVAL PERIOD RESETS THE INTERVAL TO 0.
1 2 3 4
C
R
S
CHF
EDFTR W2 0 Y C T2 T1
DF2 DF1
CY0W2RE
PRESSURE
SWITCH
(IF EQUIPPED)
TO 208/230 VAC
POWER SUPPLY
BLOWER
MOTOR
T1
T3
T4
T2 G
N
L
C
2 3 4 5 6 7 8 9 1
2 3 4 5 6 7 8 9 1
2 3 4 5 6 7 8 9 1
2 3 4 5 6 7 8 9 1
8
7
6
5 4 3 2 1
9
8
7
6
5 4 3 2 1
9
T5
DEFROST
SENSOR
COMPRESSOR
CONTACTOR
OUTDOOR FAN
MOTOR
COMPRESSOR
DUAL CAPACITOR
HEATER
PLUG
REVERSING
VALVE
SOLENID
3 AMP
FUSE
DEFROST
CONTROL
BOARD
TO INDOOR THERMOSTAT
TO DISCHARGE
AIR SENSOR
BLOWER
RELAY
TRANSFORMER
C
R
S
L2 L1
T1T2
13 56 24
24V
COM
208V
240V
ECONOMIZER JUMPER
HARNESS ASSY
9-WIRE
GB
ECONOMIZER
PLUG
ECONOMIZER
PLUG
BROWN
WHITE
WHITE
BLACK
RED BLUE
YELLOW
YELLOW
RED RED
BLUE
BLACK
GREEN
ORANGE
GREEN
GREY
GREEN
WHITE
WHITE WHITE
BLACK
BLUE
BLACK
BLACK BLACK
BLACK
BLACK
ORANGE
WHITE
WHITE
RED
RED RED
BROWN
YELLOW
YELLOW YELLOW
GREY
GREEN
BLUE
BLACK
YELLOW ORANGE
ORANGE
GREEN/YELLOW
ORANGE
BLUE
BROWN
RED RED
RED RED
RED
Legend
Field Wiring
Factory Wiring:
Low Voltage High Voltage
Note: See Installation
Instructions for wiring, application, and information concerning accessory Heat Kits and other options.

19

708546A (Replaces 7085460)
Specifications and illustrations
subject to change without notice
and without incurring obligations.
Printed in U.S.A. (05/06)
¢708546@¤
INSTALLER: PLEASE LEAVE THESE
INSTALLATION INSTRUCTIONS WITH
THE HOMEOWNER.
O'Fallon, MO