North American Tool 6274 User manual

8806274 3/12
Cordless Screwdriver
Charger:
Input: 120V -60Hz
Protection against electric
shock: Class II
Protection against moisture:
IP20
Output: 6V DC, 300mA
Charge time: about 3-5 hours
CALIFORNIA PROPOSITION 65
WARNING: You can create dust
when you cut, sand, drill or
grind materials such as wood,
paint, metal, concrete, cement,
or other masonry. This dust
often contains chemicals
known to cause cancer, birth
defects, or other reproductive
harm. Wear protective gear.
WARNING: This product or its
power cord may contain
chemicals, including lead,
known to the State of California
to cause cancer and birth
defects or other reproductive
harm. Wash hands after
handling.
Specifications
Screwdriver:
Rechargeable battery voltage:
4.8V
Max. Speed: 150rpm
Max. Torque: 2.5Nm
Battery: Ni-CD
Battery capability : 600mAh
Forward/reverse switch
LED Light
3. Insert the
bit into the
chuck
Model: 6274
This unique cordless screwdriver
is equipped with a “flip bit” quick-
loader for maximum convenience.
To load a bit:
1. Rotate the
magazine to
find desired
bit
2. Remove
the bit by
lifting up and
out
To charge the unit:
1. Connect the charger adaptor
to a power outlet and insert the
plug into the socket on the
handle.
2. The red light on the battery
display will light up once the
adaptor is connected to a power
source.
3. Once the battery is completely
charged, the red light will turn off.
If possible, remove the adaptor
after the battery is fully charged.
To unload a bit:
1. Remove the drill bit
from chuck
2. Rotate drill bit down into
“lock” position
[e-mail]

2
Safety instructions:
1. Wear protective equipment
(gloves, shoes, eyewear,
breathing filters, etc.) Do not wear
loose fitting clothing or jewelry. Tie
back long hair.
2. Disconnect from charging
equipment when performing
maintenance on or while operating
the tool.
3. Use in a clean and well lit area
4. Store the tool away form heat
and dangerous vapors. Do not
operate close to explosive or
flammable materials.
5. This is a do-it-yourself tool &
should be used as such and not
considered as heavy duty
equipment.
6. Keep tools away from children
7.When drilling into metal sheets,
use a vice to hold the metal to a
block of wood.
8. Do not use the drill or
screwdriver on an electrically live
part. Locate electrical wires or
cables in the wall before drilling
into a wall.
9. Do not try to open or
disassemble the tool or charger.
Only a specialist should perform
maintenance on the tool.
10. If the charger becomes
damaged, replace it before using
11. This tool does not require
special maintenance.
12. Disconnect the charger before
cleaning the plastic parts. Use a
wet cloth and mild soap. Do not
immerse the tool in water. Do not
use cleaning solvents to clean the
tool.
13. After cleaning a bit, make sure
that the used bit is securely in its
storage position.
14. Do not use tool bits that
cannot be inserted into the
transfer arms.
Limited Warranty: North American
Tool (NAT) Industries makes every effort
to ensure that this product meets high
quality and durability standards. NAT
warrants to the original retail consumer a
1-year limited warranty from the date the
product was purchased at retail and each
product is free from defects in materials.
Warranty does not apply to defects due
directly or indirectly to misuse, abuse,
negligence or accidents, repairs or
alterations, or a lack of maintenance.
NAT shall in no event be liable for death,
injuries to persons or property, or for
incidental, special or consequential
damages arising from the use of our
products. Shipping and handling charges
may apply. If a defect is found, NAT will
either repair or replace the product at its
discretion.
To replace a bit:
Pull the bit from its carrier and
replace with a new one as
indicated.
Push down and up on the tip of
the bit, while pulling up on the
base. Once the bit passes the
holding spring, you can pull it out.
To order replacement bits:
Send a Request to
[e-mail]
or
call 1-800-348-5004
[e-mail]
To change position:
Press the lock switch, and turn
clockwise 90 degree to rotate the
handle.
Screwing/Unscrewing:
The screwdriver is equipped with
a forward/reverse switch to
change the rotation of the unit.
1. Clockwise - push button to left
2. Counterclockwise - push the
button to the right
3. To stop rotation release the
switch.