Notifier NCS User manual

Network Control Station
NCS
Document 51095
3/08/02 Revision: B1
ECN 02-074
www.PDF-Zoo.com

Fire Alarm System Limitations
While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance!
An automatic fire alarm system—typically made up of
smoke detectors, heat detectors, manual pull stations, audible
warning devices, and a fire alarm control with remote notifica-
tion capability—can provide early warning of a developing fire.
Such a system, however, does not assure protection against
property damage or loss of life resulting from a fire.
The Manufacturer recommends that smoke and/or heat detec-
tors be located throughout a protected premise following the
recommendations of the current edition of the National Fire
Protection Association Standard 72 (NFPA 72), manufac-
turer's recommendations, State and local codes, and the rec-
ommendations contained in the Guide for Proper Use of
System Smoke Detectors, which is made available at no
charge to all installing dealers. A study by the Federal Emer-
gency Management Agency (an agency of the United States
government) indicated that smoke detectors may not go off in
as many as 35% of all fires. While fire alarm systems are
designed to provide early warning against fire, they do not
guarantee warning or protection against fire. A fire alarm sys-
tem may not provide timely or adequate warning, or simply
may not function, for a variety of reasons:
Smoke detectors may not sense fire where smoke cannot
reach the detectors such as in chimneys, in or behind walls, on
roofs, or on the other side of closed doors. Smoke detectors
also may notsensea fire on another level or floor of a building.
A second-floor detector, for example, may not sense a first-
floor or basement fire.
Particles of combustion or “smoke” from a developing fire
may not reach the sensing chambers of smoke detectors
because:
• Barriers such as closed or partially closed doors, walls, or
chimneys may inhibit particle or smoke flow.
• Smoke particles may become “cold,” stratify, and not reach
the ceiling or upper walls where detectors are located.
• Smoke particles may be blown away from detectors by air
outlets.
• Smoke particles may be drawn into air returns before
reaching the detector.
The amount of “smoke” present may be insufficient to alarm
smoke detectors. Smoke detectors are designed to alarm at
various levels of smoke density. If such density levels are not
created by a developing fire at the location of detectors, the
detectors will not go into alarm.
Smoke detectors, even when working properly, have sensing
limitations. Detectors that have photoelectronic sensing
chambers tend to detect smoldering fires better than flaming
fires, which have little visible smoke. Detectors that have ion-
izing-type sensing chambers tend to detect fast-flaming fires
better than smoldering fires. Because fires develop in different
ways and are often unpredictable in their growth, neither type
of detector is necessarily best and a given type of detector
may not provide adequate warning of a fire.
Smoke detectors cannot be expected to provide adequate
warning of fires caused by arson, children playing with
matches (especially in bedrooms), smoking in bed, and violent
explosions (caused by escaping gas, improper storage of
flammable materials, etc.).
Heat detectors do not sense particles of combustion and
alarm only when heat on their sensors increases at a predeter-
mined rate or reaches a predetermined level. Rate-of-rise
heatdetectors may be subject to reduced sensitivity over time.
For this reason, the rate-of-rise feature of each detector
should be tested at least once per year by a qualified fire pro-
tection specialist. Heat detectors are designed to protect
property, not life.
IMPORTANT! Smoke detectors must be installed in the
same room as the control panel and in rooms used by the sys-
tem for the connection of alarm transmission wiring, communi-
cations, signaling, and/or power. If detectors are not so
located, a developing fire may damage the alarm system, crip-
pling its ability to report a fire.
Audible warning devices such as bells may not alert people
if these devices are located on the other side of closed or
partly open doors or are located on another floor of a building.
Any warning device may fail to alert people with a disability or
those who have recently consumed drugs, alcohol or medica-
tion. Please note that:
• Strobes can, under certain circumstances, cause seizures
in people with conditions such as epilepsy.
• Studies have shown that certain people, even when they
hear a fire alarm signal, do not respond or comprehend the
meaning of the signal. It is the property owner's responsi-
bility to conduct fire drills and other training exercise to
make people aware of fire alarm signals and instruct them
on the proper reaction to alarm signals.
• In rare instances, the sounding of a warning device can
cause temporary or permanent hearing loss.
A fire alarm system will not operate without any electrical
power. If AC power fails, the system will operate from standby
batteries only for a specified time and only ifthe batteries have
been properly maintained and replaced regularly.
Equipment used in the system may not be technically com-
patible with the control. It is essential to use only equipment
listed for service with your control panel.
Telephone lines needed to transmit alarm signals from a
premise to a central monitoring station may be out of service
or temporarily disabled. For added protection against tele-
phone line failure, backup radio transmission systems are rec-
ommended.
The most common cause of fire alarm malfunction is inade-
quate maintenance. To keep the entire fire alarm system in
excellent working order, ongoing maintenance is required per
the manufacturer's recommendations, and UL and NFPA stan-
dards. At a minimum, the requirements of Chapter 7 of NFPA
72 shall be followed. Environments with large amounts of
dust, dirt or high air velocity require more frequent mainte-
nance. A maintenance agreement should be arranged
through the local manufacturer's representative. Maintenance
should be scheduled monthly or as required by National and/
or local fire codes and should be performed by authorized pro-
fessional fire alarm installers only. Adequate written records
of all inspections should be kept.
Precau-L-3-2002.fm
www.PDF-Zoo.com

Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be
connected to the fire alarm control panel. Disconnect all
sources of power before servicing. Control unit and associ-
ated equipment may be damaged by removing and/or insert-
ing cards, modules, or interconnecting cables while the unit is
energized. Do not attempt to install, service, or operate this
unit until this manual is read and understood.
CAUTION - System Reacceptance Test after Software
Changes. To ensure proper system operation, this product
must be tested in accordance with NFPA 72 Chapter 7 after
any programming operation or change in site-specific soft-
ware. Reacceptance testing is required after any change,
addition or deletion of system components, or after any modifi-
cation, repair or adjustment to system hardware or wiring.
All components, circuits, system operations, or software func-
tions known to be affected by a change must be 100% tested.
In addition, to ensure that other operations are not inadvert-
ently affected, at least 10% of initiating devices that are not
directly affected by the change, up to a maximum of 50
devices, must also be tested and proper system operation ver-
ified.
This system meets NFPA requirements for operation at 0-49°
C/32-120° F and at a relative humidity of 85% RH - 95% per
ULC - (non-condensing) at 30° C/86° F. However, the useful
life of the system's standby batteries and the electronic com-
ponents may be adversely affected by extreme temperature
ranges and humidity. Therefore, it is recommended that this
system and all peripherals be installed in an environment with
a nominal room temperature of 15-27° C/60-80° F.
Verify that wire sizes are adequate for all initiating and indi-
cating device loops. Most devices cannot tolerate more than a
10% I.R. drop from the specified device voltage.
Like all solid state electronic devices, this system may
operate erratically or can be damaged when subjected to light-
ning-induced transients. Although no system is completely
immune from lightning transients and interferences, proper
grounding will reduce susceptibility. Overhead or outside
aerial wiring is not recommended, due to an increased sus-
ceptibility to nearby lightning strikes. Consult with the Techni-
cal Services Department if any problems are anticipated or
encountered.
Disconnect AC power and batteries prior to removing or
inserting circuit boards. Failure to do so can damage circuits.
Remove all electronic assemblies prior to any drilling, filing,
reaming, or punching of the enclosure. When possible, make
all cable entries from the sides or rear. Before making modifi-
cations, verify that they will not interfere with battery, trans-
former, and printed circuit board location.
Do not tighten screw terminals more than 9 in-lbs.
Over-tightening may damage threads, resulting in reduced ter-
minal contact pressure and difficulty with screw terminal
removal.
Though designed to last many years, system components
can fail at any time. This system contains static-sensitive
components. Always ground yourself with a proper wrist strap
before handling any circuits so that static charges are
removed from the body. Use static-suppressive packaging to
protect electronic assemblies removed from the unit.
Follow the instructions in the installation, operating, and pro-
gramming manuals. These instructions must be followed to
avoid damage to the control panel and associated equipment.
FACP operation and reliability depend upon proper installation
by authorized personnel.
Precau-L-3-2002.fm
WARNING: This equipment generates, uses, and can
radiate radio frequency energy and if not installed and
used in accordance with the instruction manual, may
cause interference to radio communications. It has been
tested and found to comply with the limits for class A
computing device pursuant to Subpart B of Part 15 of
FCC Rules, which is designed to provide reasonable pro-
tection against such interference when operated in a
commercial environment. Operation of this equipment in
a residential area is likely to cause interference, in which
case the user will be required to correct the interference
at his own expense.
Canadian Requirements
This digital apparatus does not exceed the Class A limits
for radiation noise emissions from digital apparatus set
outin the RadioInterference Regulations of the Canadian
Department of Communications.
Le present appareil numerique n'emet pas de bruits radi-
oelectriques depassant les limites applicables aux appar-
eils numeriques de la classe A prescrites dans le
Reglement sur le brouillage radioelectrique edicte par le
ministere des Communications du Canada.
FCC Warning
Acclimate Plus™, HARSH™, NOTI•FIRE•NET™, ONYX™, and VeriFire™ are trademarks, and FlashScan®and VIEW®are registered trademarks of
NOTIFIER. NION™ and UniNet™ are trademarks of NIS. NIS™ and Notifier Integrated Systems™ are trademarks and NOTIFIER® is a registered
trademark of Fire•Lite Alarms, Inc. Echelon® is a registered trademark and LonWorks™ is a trademark of Echelon Corporation. ARCNET® is a registered
trademark of Datapoint Corporation. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. LEXAN® is a registered trademark
of GE Plastics, a subsidiary of General Electric Company.
www.PDF-Zoo.com

Table of Contents
4Document #51095 Rev.B1 3/7/02
Section 1 Installation ..............................................................................................................................................7
1.1: NCS Mounting and Connections................................................................................................................7
1.1.1: Related Documentation.....................................................................................................................7
1.1.2: NRT-NET Interface Card ..................................................................................................................8
1.1.3: NCS Equipment.................................................................................................................................8
1.1.4: Primary and Secondary Power..........................................................................................................8
1.1.5: Connecting the NRT-P3.....................................................................................................................8
1.1.6: Monitor Installation...........................................................................................................................10
1.1.6.1 Installing the MON-19BLK ....................................................................................................10
1.1.7: NCS UPS Supervision.......................................................................................................................12
1.1.7.1 NCS Computer/Monitor/Printer UPS Supervision .................................................................12
1.1.7.2 NCS Printer (only) UPS Supervision ......................................................................................13
1.1.8: Strain Relief.......................................................................................................................................14
1.2: Peripherals...................................................................................................................................................15
1.2.1: Connecting a Line Printer .................................................................................................................15
1.3: PC Configurations .......................................................................................................................................16
1.4: Software.......................................................................................................................................................16
1.4.1: Installing the NCS Software..............................................................................................................16
1.4.2: Installed Printers................................................................................................................................17
1.4.3: Read/Write CD ROM........................................................................................................................18
1.4.4: Windows 2000 Secure Desktop Configuration.................................................................................19
Section 2 Programming ..........................................................................................................................................20
2.1: Networking the NCS ...................................................................................................................................20
2.2: NCS Database..............................................................................................................................................20
2.2.1: History Database ...............................................................................................................................21
2.2.2: Graphics Database.............................................................................................................................21
2.3: Power-Up Initialization ...............................................................................................................................21
2.3.1: Data Refresh......................................................................................................................................21
2.3.1.1 Manual Data Refresh ...............................................................................................................21
2.4: The Start-Up Window..................................................................................................................................21
2.5: NCS Graphical User Interface.....................................................................................................................22
2.5.1: The Graphic Event Window..............................................................................................................22
2.5.1.1 Automatic Screen Vectoring ...................................................................................................22
2.5.1.2 Title Bar ..................................................................................................................................23
2.5.1.3 Menu Bar .................................................................................................................................23
2.5.1.4 Graphic Floor Plan ..................................................................................................................24
2.5.1.5 Key Map Area .........................................................................................................................24
2.5.1.6 Events Window .......................................................................................................................24
2.5.1.7 Acknowledged Event Box .......................................................................................................25
2.5.1.8 Screen Navigation Tools .........................................................................................................25
2.5.1.9 Date / Time Field ....................................................................................................................25
2.5.1.10 Logo Window ........................................................................................................................26
2.5.1.11 Tool Bar ................................................................................................................................26
2.5.1.12 Alarm / Trouble / Supervisory Alarm / Security Alarm Banners .........................................26
2.5.1.13 Command Area .....................................................................................................................26
2.5.1.14 Current Operator Field ..........................................................................................................27
2.6: Menu Options for Programming .................................................................................................................27
2.6.1: Administration Menu ........................................................................................................................27
2.6.1.1 System Setup ...........................................................................................................................27
2.6.1.2 Network Operations ...............................................................................................................33
2.6.1.3 Archive History Database .......................................................................................................35
2.6.2: Graphic Menu....................................................................................................................................35
2.6.2.1 Graphic Setup ..........................................................................................................................35
2.6.3: Utilities Menu....................................................................................................................................35
2.6.4: The Help Menu..................................................................................................................................36
www.PDF-Zoo.com

Document 51095 Rev. B1 3/7/02 5
Table of Contents
Section 3 Operation ................................................................................................................................................38
3.1: Normal Operation........................................................................................................................................38
3.2: Troubles.......................................................................................................................................................38
3.3: Alarms.........................................................................................................................................................39
3.4: Supervisory, Security, and Pre-Alarm .........................................................................................................41
3.5: Menu Options for Operating the NCS.........................................................................................................41
3.5.1: File Menu ..........................................................................................................................................41
3.5.1.1 Exit ..........................................................................................................................................41
3.5.2: Operator Menu ..................................................................................................................................41
3.5.2.1 Login .......................................................................................................................................41
3.5.2.2 Logout .....................................................................................................................................42
3.5.2.3 Change Password ....................................................................................................................42
3.5.3: The Action Menu ..............................................................................................................................42
3.5.4: The View Menu.................................................................................................................................43
3.5.4.1 Event Counters ........................................................................................................................43
3.5.4.2 The Detailed Events Window .................................................................................................44
3.5.4.3 Current Event Window ...........................................................................................................45
3.5.4.4 Disabled Device Window .......................................................................................................45
3.5.4.5 History Manager .....................................................................................................................45
3.5.5: Screen Navigation .............................................................................................................................46
3.5.6: Trouble with NCS and INA Equipment............................................................................................46
3.6: Read Status/Program ...................................................................................................................................47
Section 4 The History Manager .............................................................................................................................52
4.1: NCS Integrated Operation...........................................................................................................................52
4.1.1: History Backup..................................................................................................................................56
4.1.1.1 Upload/Download (UPDL) .....................................................................................................57
Section 5 The Graphic Setup Program .................................................................................................................60
5.0.1: NCS Integrated Operation.................................................................................................................60
5.1: Program Layout...........................................................................................................................................60
5.1.1: Floor Plan Tree View ........................................................................................................................61
5.1.2: Group Tree View...............................................................................................................................61
5.1.3: Floor Plan Device View ....................................................................................................................61
5.1.4: Information Windows .......................................................................................................................61
5.1.5: Tool Bar.............................................................................................................................................62
5.2: Graphic Floor Plans.....................................................................................................................................63
5.2.1: Adding Floor Plans to the NCS.........................................................................................................63
5.2.2: Selecting Floor Plans.........................................................................................................................64
5.2.3: Deleting Floor Plans..........................................................................................................................64
5.2.4: Setting Keymap Links.......................................................................................................................65
5.2.5: Screen Title .......................................................................................................................................65
5.2.6: Guidance Text ...................................................................................................................................65
5.3: Keymap Area...............................................................................................................................................66
5.4: Menu Bar Options .......................................................................................................................................66
5.4.1: File.....................................................................................................................................................66
5.4.2: Screens ..............................................................................................................................................66
5.4.3: Devices..............................................................................................................................................66
5.4.4: View ..................................................................................................................................................68
5.4.5: Setup..................................................................................................................................................68
5.4.6: Help...................................................................................................................................................69
5.5: Device Icons................................................................................................................................................69
5.5.1: Devices..............................................................................................................................................69
5.5.2: Detectors ...........................................................................................................................................70
5.5.3: Modules.............................................................................................................................................70
5.5.4: Zones.................................................................................................................................................70
www.PDF-Zoo.com

Table of Contents
6Document #51095 Rev.B1 3/7/02
5.5.5: Linked Files.......................................................................................................................................70
5.5.6: Information Labels............................................................................................................................70
5.5.7: Navigational Buttons.........................................................................................................................71
5.5.8: Delete Operations..............................................................................................................................72
5.5.9: Searching for Specific Items .............................................................................................................72
5.5.10: Rules for Setting Up Device Graphics............................................................................................72
5.6: Groups .........................................................................................................................................................73
5.6.1: Level 1 Groups..................................................................................................................................73
5.6.2: Level 2 Groups.................................................................................................................................73
5.6.3: Group Setup Restrictions ..................................................................................................................73
5.6.4: Group Navigation..............................................................................................................................73
5.7: Setup Templates...........................................................................................................................................74
5.7.1: Template Groups ...............................................................................................................................74
5.7.2: Hot Templates....................................................................................................................................74
5.8: Custom Bitmap............................................................................................................................................74
5.9: Template Files .............................................................................................................................................75
5.10: NCS Required Files...................................................................................................................................75
Appendix A: Windows 2000 Security Disable Procedure ..................................................................................76
Appendix B: Miscellaneous Software Installation ..............................................................................................77
Appendix C: Message Tables ................................................................................................................................78
www.PDF-Zoo.com

NCS Mounting and Connections Installation
NCS Manual PN 51095:B1 3/08/02 7
Section 1 Installation
1.1 NCS Mounting and Connections
The Network Control Station (NCS) contains a recognized tabletop computer with VGA graphics
for displaying all network events. The NCS is used with the Notifier Noti•Fire•Net system. The
different NCS models all come with the NRT-P3, a high-performance desktop computer.
1.1.1 Related Documentation
To obtain a complete understanding of the NCS features and related products or to become familiar
with functions in general, make use of the documentation noted in Table 1.1. The Notifier
document (DOC-NOT) chart provides the current document revision.
Table 1.1 Related Documentation
Title Number Title Number
AM2020/AFP1010
Fire Alarm Control Panel 50119/ 15088 CHG-120 50641
Liquid Crystal Display (LCD-80) 15037 Annunciator Control System 15842
Network Control Station (NCS) 51095 Lamp Driver Modules (LDM) 15885
Intelligent Network Annunciator (INA) 15092 Voice Alarm Multiplex 15889
Universal Zone Coder Installation (UZC-256) 15216 The XP Series Transponder System 15888
Product Installation Document (CCM-1) 15328 Network Adaptor Module (NAM-232) 50038
Product Installation Document
(MPS-TR) 15331 The UDACT Universal Digital Alarm Communicator/Transmitter 50050
AM2020/AFP1010 Operator Instructions 15337 FCPS-24/FCPS-24E Field Charger/Power Supply
Installation, Operation and Application Manual 50059
Notifier Device Compatibility Document 15378 Video Graphics Annunciator System (VGAS)
Installation Manual 50251
Analog Fire Panel (AFP-200) 15511 Media Interface Board (MIB) 50255
Analog Fire Panel Installation Manual (AFP-400) 50253 Repeater (RPT) 50256
Analog Fire Panel Programming Manual (AFP-400) 50259 Noti•Fire•Net Manual 50257
Analog Fire Panel Operating Manual (AFP-400) 50260 Smoke Control Manual 15712
Canadian Requirements for the AM2020/AFP1010 15631 SLC Manual 51253
Network Interface Board (NIB-96) 15666 MMX-2 Installation Instructions M500-03-00
RM-1 Series Remote Microphones 51138 XP5 Series Transponders 50786
NBG-12LX Pull Station 51093 ACT-2 Audio Coupling Transformer 51118
www.PDF-Zoo.com

Installation NCS Mounting and Connections
8NCS Manual PN 51095:B1 3/08/02
1.1.2 NRT-NET Interface Card
The NCS communicates with Noti•Fire•Net through the Network interface card (NRT-NET) and
the Media Interface Board (MIB). The NRT-NET interface card plugs directly into a computer
expansion slot located on the NCS computer. The MIB, which supports the physical connection to
the network, plugs onto the NRT-NET card to complete the network interface. The NRT-NET
interface card provides the following features:
• Allows the NCS computer to communicate on Noti•Fire•Net
• Accepts the following choices of Media Interface Boards:
- twisted-pair (MIB-W)
- Fiber optic (MIB-F)
Figure 1.1 NRT-Net Card
1.1.3 NCS Equipment
The Network Control Station is a kit comprised of:
• a computer
• A MON-19BLK monitor (UL 864 Listed 19 inch monitor)
Refer to Table 1.2 for model numbers and components.
Note: The monitor and mouse, as well as the printer if one is used, must be installed in the same room as the NCS in order
to comply with UL listing requirements.
A PRN-5 printer can be ordered separately.
The NCS computer is referred to in this manual as the NRT-P3. Table 1.2 lists the NCS model numbers
that include computers referenced as NRT-P3.
Table 1.2 NCS Equipment Options
1.1.4 Primary and Secondary Power
The NCS requires connection to a separate dedicated primary AC fire alarm circuit, which must be
labeled "FIRE ALARM." This AC circuit must connect to the line side of the main power feed of
the protected premises. No other equipment can be powered from the fire alarm circuit. The
primary AC circuit wire run must run continuously, without disconnect devices, from the power
source to the NCS. Overcurrent protection for this circuit must comply with Article 760 of the
National Electrical Code as well as local codes. Where an NCS is required, the use of an UL-864
approved supervised UPS is also required. When using a UPS, NCS input voltage must be 115
VAC. The use of 230 VAC is not permitted when employing a UPS.
1.1.5 Connecting the NRT-P3
The following steps must be completed when connecting the NRT-P3 (refer to
Figure 1.2 and Figure 1.3).
Model # Components
NCS-M19F NCS computer, mouse, 19" monitor, fiber optic data link
NCS-M19W NCS computer, mouse 19" monitor,wire data link
LED illuminates to indicate
that NFN is receiving data.
LED illuminates to indicate
that NFN is transmitting data
.
LED illuminates to indicate
activity on Channel A.
LED illuminates to indicate
activity on Channel B.
Monitors normally closed contacts of
uninterruptible power supply (UPS). If
unused, cover pins using supplied jumper.
JP3, IRQ7
The jumper
provided must
cover these pins if
the NCS is not an
NRT upgrade.
Note: If the NCS
is an NRT
upgrade, the pins
at JP3, IRQ3 must
be covered.
JP6 - Present on the NRT-NET card of an
NCS or later model NRT. Do not remove
the jumper at JP6, which is set at 300H.
www.PDF-Zoo.com

NCS Mounting and Connections Installation
NCS Manual PN 51095:B1 3/08/02 9
1. Cut off the plug end of the computer power cord.
2. Plug the socket end of the power cord into the computer.
3. Remove the screws from around the power supply of the NRT-P3.
4. Attach the PCLB-6 enclosure without the cover to the back of the NRT-P3 using these screws.
5. Install a 3/4-inch (19.05 mm) conduit and fitting in the knock-out hole of the Power Cord
Locking Bracket cover (refer to Figure 1.3).
Caution: Size the 3/4-inch (19.05 mm) conduit so the line cord can reach a junction box at the
other end of the conduit.
6. Thread the power cord through the cover and conduit.
7. Attach the PCLB-6 cover to the PCLB-6 using the mounting screws supplied. Ensure that the
PCLB-6 cover holds the power cord socket firmly in place.
8. Connect the power cord to the HSP-121B power line protector as shown in
Figure 1.4.
Note: The HSP-121B power line protector must reside in a junction box.
9. Connect 115 VAC, 50/60 Hz primary power or 230 VAC, 50/60 Hz primary power to the HSP-
121B as shown in Figure 1.4. Primary power connected to the HSP-121B (115 VAC or 230
VAC) depends upon the position of the voltage selection switch shown in Figure 1.2 and
Figure 1.3. All wiring must remain in conduit.
WARNING: Improper voltage selection can damage the NCS and void the warranty on the
back cover of this manual.
10. Turn power switch on for the circuit.
11. Replace the cover on the PCLB-6 enclosure and secure with two screws.
12. Connect the monitor to the display adapter video connector on the back of the computer (refer
to Figure 1.2). Connect the other end of the video cable to the monitor. The video cable is
provided with screws for secure attachment.
13. Align the keyboard cable plug to mate with the notch in the computer's jack and insert cable.
14. Connect the mouse to the mouse port at the back of the NRT-P3.
15. Refer to Figure 1.5 for monitor power application.
Figure 1.2 NRT-P3 Connections
!
!
Monitor
connection
EIA-232
COM Ports
3 and 4 Mouse/Keyboard Port
Remove these
screws and reuse
for mounting the
PCLB-6 plate
Power
Cord
Socket
Voltage
Selection
Switch
Not used
NCSonyx3bk.cdr
Noti•Fire•Net
Connections
UPS
Supervision
Cable
Connection
Power Switch
(disabled at
factory) Not Used
Software Key
connection
EIA-232
COMPorts
1 and 2
Not Used
Not Used
Speaker Connector
Not Used
Microphone Connector
NRT-NETPC
B
LEDs
NRT-NETPCB Card
www.PDF-Zoo.com

Installation NCS Mounting and Connections
10 NCS Manual PN 51095:B1 3/08/02
• The NRT-P3 requires 115 VAC, 50/60Hz primary power or 230 VAC, 50/60 Hz primary power depending upon the
position of the voltage selection switch shown in Figure 1.2 andFigure 1.3.
• Where an NCS is required, the use of a supervised Uninterruptable Power Supply (UPS) is also required (see Figure
1.6)
• The NCS is not suitable for use as a receiving unit.
• The front power switch for the NRT-P3 has been permanently fixed in the ON position.
Figure 1.3 Attaching the PCLB-6 to the NRT-P3
Figure 1.4 Connecting the Power Cord and Primary AC Power
to the Power Line Protector
1.1.6 Monitor Installation
1.1.6.1 Installing the MON-19BLK
The followingsteps must becompleted when connecting the MON-19BLK to the Junction Box and
NRT-P3 (refer to Figure 1.5).
1. Connect the AC Power Cord on the MON-19BLK to the HSP-121B Junction Box.
2. Connect the DB-15 video cable to the video card slot on the NRT-P3.
Power Cord
Voltage selection
Switch
PCLB-6
(without cover)
Mounting Screws
Knockout PCLB-6 Cover
Mounting Screw
PCLB5Bb.cdr
nrtpwcrd.cdr
PCLB5Ba.cdr
AC
NEUT
GND
AC
NEUT
GND
L
I
N
E
E
Q
U
I
P
Ground - Green
Neutral - White
AC - Black
Power Cord
Fuse
To 115 VAC, 50/60
Hz Primary Power or
230 VAC, 50/60 Hz
Primary Power
Black
White
Green
HSP-121B Conduit
PCLB-6
Light ON - Normal
Light OFF - Requires Service
15 AMPS
MAX
Junction Box
hsp-121b.cdr
www.PDF-Zoo.com

NCS Mounting and Connections Installation
NCS Manual PN 51095:B1 3/08/02 11
Figure 1.5 Installation of MON-19BLK
DB-15 Cable
MON-19BLK
NCS Computer
Monitor
Connection
Ground - Green
Neutral - White
Power Cord
Fuse
B
lack
W
hite
G
reen
HSP-121B
Junction Box
AC - Black
NCSmoninstonyxnrtnet.cdr
www.PDF-Zoo.com

Installation NCS Mounting and Connections
12 NCS Manual PN 51095:B1 3/08/02
1.1.7 NCS UPS Supervision
1.1.7.1 NCS Computer/Monitor/Printer UPS Supervision
Where a Network Reporting Terminal (NCS) is not ancillary, the use of a supervised 115 VAC
Uninterruptable Power Supply (UPS) is required. Refer to Figure 1.6 and Figure 1.7 for wiring
information. A networked AM2020/AFP1010 or INA with an MPS-24A Power Supply must be
located within three feet (.9144 m) of the UPS and wiring must be in conduit.
Figure 1.6 NCS Computer UPS Supervision
9
0
8
1
7
2
6
3
5
4
+
-
Use cable P/N 71033 (supplied
with the NCS) from
NRTNETPCB to UPS. Cut and
strip wires as needed. Make all
connections in conduit.
Negative Bar Positive Bar
To AC Power of
NCS, Printer, or CRT
AC Input
Inverter
Failure
DC/AC Inverter
AC
Load
115 VAC
AC Line
115 VAC
Note: The Inverter is equipped
with automatic transfer. Refer to
the schematic in the instruction
manual for internal wiring.
Note: Wiring should be in the same
cabinet or use less than 3 feet of conduit.
47k ELR
Utility Failure
(optional)
DC
Output
DC
Output
Charger 1 Charger 2
NCSsupsfsonyxnrtnet.cdr
NC NC
COMM
NRT-P3 Computer
FMM-1
Low Current Rectifier Failure
Remote Equalize
Remote Sense (-) Remote Sense (+)
Load Sharing
Low Current
Rectifier Failure
Remote Equalize
Remote Sense (-)
Remote Sense (+) Load Sharing
www.PDF-Zoo.com

NCS Mounting and Connections Installation
NCS Manual PN 51095:B1 3/08/02 13
1.1.7.2 NCS Printer (only) UPS Supervision
Figure 1.7 NCS Printer UPS Supervision
1
(NO)
4
(NO)
5(C)
6
(NC)
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
2
3
90
81
72
63
54
+
_
2(C)
3
(NC)
Relay Contacts Are Rated
500 mA, 28V DC
500 mA, 28V AC Resistive Load
Chassis Ground
Input Power 120V AC, 60 Hz 8A AC Maximum
No Connection
No Connection
120V AC Output Of UPS
120V AC Output Of UPS
120V AC Output Of UPS
AC
Input
Fail
Battery
Fail
47K
ELR
FMM-1
UPS
System Control
Board
EMI
Line
Filter
Static
Switch Transformer
Inverter
Charger
Battery
Instrumentation and Control System, Inc.
UPS, Model Number 9300057
Total Output Load
5A AC Maximum
Battery Backed Up
Note: Cut and Strip
Wires on Cable
Assembly P/N 71033
(provided with NCS),
and connect as shown.
upsprn1fsconyxnrtnet.cdr
}
NRT-NETPCB
UPS Supervision Port
SoftwareType
ID "MTRB"
SPARE H GND N
H GND N
H GND N H N
H GND N
www.PDF-Zoo.com

Installation NCS Mounting and Connections
14 NCS Manual PN 51095:B1 3/08/02
1.1.8 Strain Relief
Strain relief for wiring attached to the NCS wire terminals on the MIB-W is provided by a
protective cover (P/N 08275). The protective cover is supplied with the MIB-W.
The following steps must be completed to connect the protective cover with strain relief:
3. Feed wires to be connected to the terminal block through the back or side access hole of the
protective cover. The hinged covers of the unused access hole can be closed.
4. Attach the wires to the pluggable terminal block.
5. Snap the strain relief assembly over the pluggable terminal block. Use tie wrap to secure the
wires to the protective cover (refer to Figure 1.8).
Figure 1.8 Strain Relief Assembly
Wiring Access Holes and
Hinged Covers
Tie Wrap Around Wire and
Hinged Cover
Cable Restraint
(add after assembly)
Protective Cover
(P/N 08275)
Strain Relief Assembly
(snaps over pluggable terminal block)
strainre.cdr
NCSonyx3back.cdr
NRT-
NETPCB
www.PDF-Zoo.com

Peripherals Installation
NCS Manual PN 51095:B1 3/08/02 15
1.2 Peripherals
1.2.1 Connecting a Line Printer
A printer can be connected to the NCS to print fire alarm and trouble signals (refer to Figure 1.9
and Table 1.3).
Figure 1.9 Serial Port Connections for a Printer Connected to NRT-P3
To connect a PRN-4 or PRN-5 printer to the NCS, a cable with the connections shown in Table 1.3
must be prepared.
Table 1.3 Printer Connections
• Only one NCS (including keyboard, mouse, monitor, or any one of these) can be present on the network for other than
National Fire Protection Association (NFPA) 1996-72 Local Service.
• Where an NCS is required, the use of a supervised 115 VAC UPS is also required (see Figure 1.6 or Figure 1.7).
• Locate the printer in the same room as the NCS.
• This printer connection is not for use with VeriFire. Refer to the VeriFire documentation for further information.
DB 25 connector from PRN
or another listed EDP printer Cable
DB 9 connector
NCSdbcxonyxnrtnet.cdr
NCS
DB9 Printer DB25
22
33
57
4 and 6
jumpered
together
820
www.PDF-Zoo.com

Installation PC Configurations
16 NCS Manual PN 51095:B1 3/08/02
1.3 PC Configurations
To run the NCS program your system must be setup for the following configurations:
1024 x 768 resolution, large fonts, and 65k colors. Refer to Figure 1.10. To set these
configurations, select the Start menu and Settings/Control Panel, double-click Display and select
the Settings tab.
Figure 1.10 PC Configurations
For Windows 2000, the font size is located in a submenu of the Settings screen. Click the
"Advanced" button that appears at the bottom right of the Settings screen. On the next screen,
choose "Large" for font size.
Additionally, for Windows 2000, the Active Desktop setting must be off.
1.4 Software
1.4.1 Installing the NCS Software
Make sure to read the entire set of instructions prior to beginning the NCS software installation.
The NCS software requires Windows 2000 Professional Edition with Service Pack 1or higher, or
Windows NT® with Service Pack 5. The following steps must be completed to install NCS
software in Windows NT® Workstation 4.0 or in Wnidows 2000.
Note: If the NCS is the Master Time Keeper on the network, installing this software will cancel the setting and a Master
Time Keeper will not exist on the network. Enter the date/time in the NCS Local Programming Dialog Box for the NCS to
become the Master Time Keeper again.
Windows NT®is a registered trademark of Microsoft Corporation.
1. Insert the CD-ROM into the appropriate drive. The Setup program will launch automatically if
Autorun is enabled. Otherwise, continue with steps 2 through 10 that follow.
2. Click on the Start button, select Run...
3. At the Command Line prompt, type X:\NCS, where X is your CD drive letter. Steps 2 and 3
will only be necessary for PCs that do not have the Autorun feature enabled.
n
cspcconfig.jpg
www.PDF-Zoo.com

Software Installation
NCS Manual PN 51095:B1 3/08/02 17
4. An InstallShield Self-Extracting.exedialog box will appear, select YES to continue installing
the NCS. InstallShield will start extracting the necessary files for installing the NCS.
5. A Welcome dialog box will appear. Select NEXT to continue installing or CANCEL to return
to the desktop.
6. A User Information dialog box will appear next. Type your name and company at the
designated prompts. Select NEXT to continue or CANCEL to return to the desktop. The
location of the installation directory will be displayed if it exists, and the user will be asked if
he/she would like to make a backup.
7. Next a Select Program Folder dialog box appears. The NCS must be installed in the
directory provided.
8. A Setup Type dialog box will now appear. Choose Typical, Compact or Custom setup by
clicking in the appropriate circle. Select NEXT to continue installing, BACK to view the
previous screen or CANCEL to return to the desktop.
• Typical Install - Installs the most common options, recommended for most users.
• Compact Install - Not available at this time.
• Custom Install - The user choosesthe installed options, recommended for advanced users. The
Select Program Folder dialog box displays for this purpose.
9. Next a Start Copying Files dialog box appears showing the type of setup, target folder and
user information that was provided. Select NEXT to begin copying files, BACK to change any
settings or CANCEL to return to the desktop.
10. The NCS will now install the NCS. When setup is complete, a Setup Complete dialog box
appears informing you that the computer will be rebooted. Press OK to perform the reboot.
Caution: The NCS Communications Driver may have to be changed. If the NCS is installed on a
PC that did not contain the NRT (Network Reporting Terminal), it will use IRQ5 or IRQ7.
The NCS Installation Program sets the IRQ to IRQ5. On Onyx computers,or computers that already
use IRQ5, this must be changed to IRQ7. Please be sure the jumper selection on the NRT-NETPCB
card is set to IRQ7. In addition, please complete the following steps to configure the software:
1. Open a text editor, such as Notepad.
2. Open file ptp20020.ini. This file is located in the \notifier\ncs directory.
3. Look for IRQLevel = REG_DWORD 0x05. Change the 0x05 to 0x07.
4. Save the file, close Notepad.
5. Open the DOS command prompt, and change to the \notifier\ncs directory.
6. Type "regini ptp20020.ini"
7. This completes the software configuration. Reboot the computer for the change to take
effect.
To verify that the NCS Communications Driver is configured correctly, follow these steps in
Windows 2000.
1. From the Start Menu, open Control Panel, then double click on Administrative Tools.
2. Double click on Computer Management.
3. Navigate to System Information, then select Hardware Resources, followed by IRQs.
4. Verify that IRQ7 is displayed, and the Device indicates ptp20020.
1.4.2 Installed Printers
Two printers may be installed to the NCS: an NCS Graphics Printer (optional, any Microsoft Win-
dows compatible printer that is UL ITE listed and installed in the same room as the NCS) which is
used to print out graphics, reports, etc. and an NCS Line Printer (the PRN) which is used only to
print out text.
Note: The NCS Graphic Printer must be a laser printer.
Installing The Graphics Printer
1. Exit the NCS application.
!
www.PDF-Zoo.com

Installation Software
18 NCS Manual PN 51095:B1 3/08/02
2. From the Start Menu, select Settings, and then Printers.
3. Double-click on the "Add Printer" icon.
4. The Windows NT®Installation Wizard will start to add the new printer.
5. Select the "My Computer" button, click next. The following items should be selected on the
next screens.
• The printer must be connected to LPT1.
• Select the printer that is to be hooked up to the system.
• Select Not Shared.
• Name the printer “NCS Graphic Printer”.
Caution: This entry is case sensitive: the printer name must be entered exactly as shown.
6. In the printer dialog box, highlight the printer just installed, right click and select properties.
Installing The Line Printer
1. Exit the NCS application.
2. From the Start Menu, select Settings, and then Printers.
3. Double-click on the "Add Printer" icon.
4. The Windows NT®Installation Wizard will start to add the new printer.
5. Select the "My Computer" button, click next. The following items should be selected on the
next screens.
• The printer should be connected to LPT1 or a serial port.
• Select the printer that is to be hooked up to the system.
• Select Not Shared.
• Name the printer “NCS Line Printer”.
6. In the printer dialog box, highlight the printer just installed, right click and select properties.
Note: If the NCS Line Printer is connected to a serial port, the port settings must match the printer settings.
1.4.3 Read/Write CD ROM
File Directories on the NCS contain
information specific to normal NCS
operation. User-defined directories for
capturing history files (.HIS) may also exist
on the NCS. The files in these directories
may be backed up to the Read/Write CD
ROM. The Read/Write CD drive is located
as shown in Figure 1.11. Follow the steps
below to copy NCS information onto a CD.
1. Exit NCS
Caution: Exiting the NCS application disconnects the NCS from Noti•Fire•Net which leaves the
building unprotected and the NCS not performing Life Safety functions. A firewatch is
recommended in all areas where the NCS is designated as the primary or only reporting station.
2. Load a CD into the CD drive. A CD-R is a one-time writeable CD, a CD-RW can be written
over multiple times.
Caution: Once the CD is in the drive, the door must remain OPEN until the CD is removed. If the
drive opens while the door is shut, it will hit the door and may become jammed.
3. Double-click on the "Create CD" icon on the NCS desktop. Easy CD Creator™ will appear.
4. Select "DATA"
!
RESET
POWER
Figure 1.11 NCS Computer, Front View, Door Ope
n
Read/
Write CD
drive
location
!
!
www.PDF-Zoo.com

Software Installation
NCS Manual PN 51095:B1 3/08/02 19
5. Select "DATA CD". The program will launch at this point.
6. Select files for backup. The directory C:\NOTIFIER\NCS contains important information and
should be included in the backup. Click the ADD button after each selection.
7. Click "Create CD" button on the toolbar. The CD creation Setup comes up with default
settings.
8. Click OK. The CD writer will copy the selected files onto the CD. When copying is complete,
the message "CD created successfully" will appear.
9. Click OK.
1.4.4 Windows 2000 Secure Desktop Configuration
The Onyx computers come pre-installed with Secure Desktop. This application prevents
unauthorized access to non-fire applications. To fully enable the software, and to comply with
UL-864, follow these steps:
1. From the Start Menu, select Secure Desktop, then Secure Setup.
2. The current configuration will indicate "Windows Explorer or Program Manager (Default)".
Change this to "Secure Desktop Icon Settings and General Options".
This will enable operation of certain applications only, such as the NCS and related programs,
VeriFire programs, and CD Burner software. The Windows Explorer Desktop will be replaced with
the Secure Desktop.
www.PDF-Zoo.com

Programming Networking the NCS
20 NCS Manual PN 51095:B1 3/08/02
Section 2 Programming
2.1 Networking the NCS
The Network Control Station (NCS) annunciates system signals on Noti•Fire•Net. Equipment that
connects to Noti•Fire•Net and communicates with other equipment using the network will be
referred to as a network node (for example: AM2020, AFP200 with NAM-232, AFP1010, INA, or
NCS). Noti•Fire•Net is a peer-to-peer network (refer to Figure 2.1), and can be logically grouped
together to form systems. For more information on Noti•Fire•Net, refer to the Noti•Fire•Net
Manual.
The functions of the NCS shall include:
• Display of all events on the network.
• Provide the ability to acknowledge, reset and signal silence all events.
• Provide the ability to graphically set up and annunciate the points to be monitored.
• Allow read status and alter status operation to all fire panels that provide this ability.
• Upload / download programming information for archiving purposes for all fire panels that provide this ability.
• Provide a history viewer with filters that can be run outside the NCS application.
• Setup different levels of operator interaction, based on passwords.
Figure 2.1 Noti•Fire•Net Network
2.2 NCS Database
Upon power-up, the NCS checks for the presence of the databases. If it can not find them, a
warning dialog box will be displayed, and a system error message will be logged to the history
manager and current event window. If the Run Time or Administrator database is missing, the NCS
will not be able to execute, and the program will not start. The only way to correct this situation is
to re-load the NCS software, or restore the databases. If the history database is missing, a new file
will be created. If that database already exists, it will be opened.
MIB
nrtntwka.cdr
AFP-200
NAM-
232
MIB
MIB
AM2020
AFP1010
NCS
INA
Fiber Optics
or Single
Twisted-Pair
www.PDF-Zoo.com