Notifier ID50 SERIES User manual

ID50/60 operating
manual
997-264-000-8, Issue 8 January 2007

ID50 Series Panel - Operating Manual
Contents
i 997-264-000-8, Issue 8
January2007
Contents
1 Introduction 1
1.1 Associated Documents 1
1.2 The ID50 / ID60 Series Panel 1
1.2.1 Device Type Abbreviations 2
1.3 Cleaning 2
2 Panel Controls and Indicators 3
2.1 Controls 3
2.2 Indicators 4
3 Automatic Alarms - What to do 5
3.1 Fire 5
3.1.1 Fire in Delayed Mode 7
3.2 Pre-alarm 8
3.3 Fault 9
3.2.1 Power Fail 10
3.3 Plant Alarm 11
4 Operator Actions at Panel 12
4.1 Introduction 12
4.1.1 Liquid Crystal Display 12
4.1.2 InternalBuzzer 13
4.1.3 Access Codes 13
4.1.4 Keyswitch 14
4.2 MUTE BUZZER Pushbutton 14
4.3 EXTEND DELAY Pushbutton 14
4.4 END DELAYS/EVACUATE Pushbutton 15
4.5 SILENCE/RESOUND Pushbutton 16
4.6 RESET Pushbutton 17
4.7 Numeric Keys 18
4.7.1 Cancellation/Termination Button 18
4.7.2 Level 2 Options Menu Button 18
4.8 Level 2 Option Menus 19
4.9 TEST - User Option 20
4.9.1 LEDs - User Option 21
4.9.2 LCD - User Option 21
4.9.3 Zones - User Option 22
4.9.4 Auto High Test - User Option 24
4.9.5 Outputs - User Option 25

ID50 Series Panel - Operating Manual
Contents
ii997-264-000-8, Issue 8
January2007
4.9.6 Buzzer - User Option 27
4.9.7 Keyboard - User Option 27
4.10 DISABLE / ENABLE - User Option 28
4.10.1 Zones - User Option 28
4.10.2 Outputs - User Option 31
4.10.3 Day Mode - User Option 32
4.10.4 Delays - User Option 33
4.11 CLOCK - User Option 34
4.11.1 Time - User Option 35
4.11.2 Date - User Option 36
4.12 VIEW MODE - User Option 37
4.12.1 Log - User Option 38
4.12.2 Devices - User Option 39
4.12.3 Faults - User Option 40
4.12.4 Input Events - User Option 41
4.12.5 Disabled - User Option 42
4.12.6 Alarm Count - User Option 42
4.12.7 Voltages - User Option 43
4.12.8 Version - User Option 44
4.13 Commissioning 44
4.14 Print 44
Appendix 1 - Log Book A1-1
Appendix 2 - Maintenance A2-1
Appendix 3 - ID60 Single Loop Panel
Differences A3-1

ID50 Series Panel - Operating Manual
Contents
iii 997-264-000-8, Issue 8
January2007
ID50 Series Panel
ID50 Series Panel

ID50 Series Panel - Operating Manual
Introduction
1 997-264-000-8, Issue 8
January2007
1 Introduction
This manual contains operating instructions for the ID50
and ID60 Series Fire Detection Panels. Differences
between the ID50 and ID60 panels are given in
Appendix 3.
Users of this manual are assumed to be working with a
panel that has already been installed and configured
appropriately for the area under its supervision.
1.1 Associated Documents
This manual does not describe the installation or
configuration procedures of the panel. For information
on these topics, refer to the ID50 Series
Panel - Installation, Commissioning and
Configuration Manual (Ref. 997-263-000-X).
1.2 The ID50/ ID60 Series Panel
Thepanel,assupplied by NOTIFIER,isa 1-loop, 16-zone
Analogue Addressable Panel. The single loop has the
capacity for up to 99 analogue sensors plus up to 99
modules and, in some installations, panels may also be
connectedto repeatersusingtheRS485Communications
Link.
All the control and operation functions described in this
manual can be carried out using the pushbuttons on the
front of the panel.
A keyswitch is provided which, when set to the right, has
thesame effectas enteringan access 2 passcode.Set it
to the centre to cancel out of all menus and return to the
Status: NORMAL display. This indicates access level 2
is de-selected.

ID50 Series Panel - Operating Manual
Introduction
2997-234-000-8, Issue 8
January2007
1.2.1 Device Type Abbreviations
Throughout this manual the panel may refer to devices
by an abbreviated name. The following table lists the
device type abbreviation and its description.
Abbreviation Type Description
AUX Plant Warning Input
AVR* Advanced VIEW™ Reference*
AVS* Advanced VIEW™ Sensor*
CTE Monitored (Relay Type) Output (VdS)
CTL Monitored (Relay Type) Output
ESE Extinguishant System Output (VdS)
ESM Extinguishant System
ESO Monitored Extinguishing System Output
EST Extinguishant Monitor System Trigger
ION Ionisation Smoke Detector
IRL Immediate Release Input
MCP† Manual Call Point†
MLT Advanced Multi Sensor
MNS Monitor module (no short-circuit)
MON Fire Alarm Monitor Input
MRL Manual Release Input
OPT Optical/Photo-electric Smoke Detector
OPX Optiplex Multi-sensor
RLE Unmonitored(RelayType)orO/COutputs(VdS)
RLY Unmonitored(RelayType)orO/COutputs
SDR Monitored (Sounder Type) Output
SM4* SMART Multi-criteria Sensor*
TMP Temperature Detector
TxD MonitoredTransmissionRoutingOutput
ZMX Conventional Detector Input
Note: Devices marked ‘*’ are supported by the ID60
Panel only. The Device marked ‘†’ is also
available as ‘DKM’ - not used in this application
(provided to be compatible with VdS
requirements).
1.3 Cleaning
The panel case may be cleaned periodically by wiping
with a soft, damp lint-free cloth.
Do not use solvents.

ID50 Series Panel - Operating Manual
Panel Controls & Indicators
3 997-264-000-8, Issue 8
January2007
2 Panel Controls and Indicators
The panel’s controls and indicators are used to operate
theoverall system anddisplaythe panelstatus.The panel
hasfive functionpushbuttons,twelve numeric/cursorkeys
andthirty-twozonalLEDindicators,two‘FIRE’indicators
and fourteen system status LED indicators.
An access level 2 keyswitch is provided to enable the
operation of panel controls and access to user menus
without entering a passcode via the numeric keypad.
2.1 Controls
The pushbuttons are listed below, together with
references to the relevant sections of the manual:
Function Pushbuttons
•MUTE BUZZER - (Section 4.2).
•EXTEND DELAY - (Section 4.3).
•END DELAY/EVACUATE1- (Section 4.4)
•SILENCE/RESOUND - (Section 4.5).
•RESET - (Section 4.6).
1Also configurable as Transmission Device (TD)
Enable/Disable.
Numeric/Cursor Keys
•Numeric/Cursor keys - (Section 4.7).
Keyswitch
Turn the keyswitch to enable level 2 access. The
keyswitch provides an alternative to entering the level 2
access code via the numeric keys. See Section 4.1.3
and Section 4.1.4.

ID50 Series Panel - Operating Manual
Panel Controls & Indicators
4997-264-000-8, Issue 8
January2007
2.2 Indicators
The panel status indicators comprise three groups:
a. Zone Status LED indicators.
b. Panel/System LED indicators.
c. Visible/Audibleindicators.
Zone Status LED Indicators
•ZONE FIRE - these LEDs indicate affected zone(s).
•ZONE FAULT/DISABLE/TEST - these LEDs indicate
affected zone(s).
Panel/System LED Indicators
•FIRE - these LEDs indicate a fire condition.
•Other System Status LEDs:
FAULT indicates a fault has been
detected by the panel.
DISABLEMENT indicates the presence of a
manually-configured
disablement.
TEST indicatesatest is in progress.
DELAYACTIVE indicates delays are active.
FIRE OUTPUTACTIVEindicates fire outputs have
been operated.
PRE-ALARM1indicates a pre-alarm
condition exists.
POWER indicates status of power
supply.
SYSTEM FAULT indicates the CPU has reset
orasystemfaulthasoccurred.
EARTH FAULT indicates an earth fault has
occurred.
PLANTALARM2indicates a fault or warning
fromaplant-monitoringdevice.
FIRE CONTROL O/P: FAULT/DISABLED
indicates a fire control output
fault or disablement.
FIRE OUTPUT: FAULT/DISABLED
indicates a fire output fault or
disablement
SOUNDER: FAULT/DISABLED
indicates a sounder circuit
fault or disablement
POWER SUPPLY FAULT
indicates an unsatisfactory
power supply to the panel.
1ThisLEDisalsoconfigurableasSOUNDERSSILENCED.
2This LED can be configured as: FAULT O/P: FAULT/
DISABLED.
Visible/Audible Indicators
•Liquid Crystal Display (LCD) - (Section 4.1.1).
•Internal Buzzer - (Section 4.1.2).

ID50 Series Panel - Operating Manual
Automatic Alarms - What to do
5 997-264-000-8, Issue 8
January2007
3 Automatic Alarms - What to do
Before any automatic alarms have been sounded the
panel only operates in display mode (quiescent state).
Theusermust then turn the keyswitchtothe right or enter
aLevel 2access code to enable the panel’spushbuttons.
Only one alarm condition can be displayed at a time
onthe LCD.If firealarms,faultsand/or warningconditions
(Plant Alarm) are present on the panel at the same time,
they are displayed in the following priority order:
a. Fire Alarms.
b. Pre-alarms
c. Faults.
d. Warnings.
The alarm condition is registered in a log.
The user must then enter a Level 2 access code, or turn
the keyswitch to the right, to enable the panel’s
pushbuttons. When the Level 2 access code is active,
the ‘
2
/
8
’ buttons can be used to scroll through the
alarms and the ‘
4
’ button will display the first alarm.
3.1 Fire
Automatic panel actions:
If the system detects a fire alarm, the panel always does
the following automatically:
a. Operates the internal (high-pitched) buzzer.
b. Illuminates the red FIRE LEDs, and the numbered
red ZONE FIRE LED.
c. Displays information on the LCD regarding the fire
condition. The information includes device address
and device location (see example below).
FIRE 02 / 05 Z01 M12 MCP 11:59
MAIN BUILDING BASEMENT ROOM 23
Note: If a delay is configured DELAYED is displayed on
the top line of the LCD. When a delay is active the
DELAYACTIVELED illuminatesandthe remaining
time before the first day mode delay expires is
displayedevery 5 secs.The LED onlyextinguishes
when the delay period has expired.
d. Operatesthe sounders and output modulesaccording
to the panel’s Control-by-Event (CBE) Rules
(configured during the Commissioning stage).
ALARM
CONDITION
ZONE
NUMBER
DEVICE
ADDRESS
ZONE TEXT
TIME OF LOGGED
ALARM CONDITION
DISPLAYED
ALARM
CONDITION
LOGGED
ALARM
CONDITIONS
DEVICE
TYPE
DEVICE
TEXT

ID50 Series Panel - Operating Manual
Automatic Alarms - What to do
6997-264-000-8, Issue 8
January2007
Recommended operator actions:
Note: Intherecommendedoperatoractionsdescribedbelow
onlyMUTEBUZZERand ENDDELAYareselectable
atAccess Level1.TheoperationofEXTEND DELAY,
EVACUATE,SILENCE,RESOUNDandRESETmust
onlybepossibleataccessLevel2,inaccordancewith
the requirements of EN54:Part 2.
1Operate the MUTE BUZZER pushbutton to silence
the panel’s internal buzzer.
2Follow prescribed instructions for evacuation of
premises,notification of FireBrigadeand investigation
of source of fire.
3If additional sounder operations are required to
achieve a complete and immediate evacuation of the
premises, press the END DELAY /EVACUATE
pushbutton (needs access level 2). This will cause
the internal buzzer to resound, so press the MUTE
BUZZER pushbutton to silence.
4When more than one fire Alarm condition is present,
itis possible to manually scroll through all logged Fire
Alarm conditions using the ‘
2
/
8
’ arrows.
Note: With multiple alarms, the LCD displays the first
alarm event.
5When evacuation of the premises is achieved, or at
the direction of an authorised person, the Alarm
Sounders may be silenced by pressing the
SILENCE / RESOUNDpushbutton.
Note: The SOUNDERS SILENCED LED illuminates if
this option was configured during panel
commissioning. The default function for this LED
is PRE-ALARM.
6To re-start the sounders, press the
SILENCE / RESOUND pushbutton. You must wait at
least 10 seconds after having originally silenced the
soundersbeforeresoundingthem. If the SOUNDERS
SILENCED LED option was configured during
commissioning to illuminate, this will now extinguish.
7When the cause of the alarm has been removed and
call points and input devices have been locally reset,
the system may be returned to ‘Status: NORMAL’*by
pressing the RESET pushbutton.
*Unless the Site name menu was edited during
commissioning-refer to Section 4.1.1 Liquid crystal
Display.
3
4
7
Status: NORMAL
Sat 01/12/2001 00:00:00
5
6
1
EN54-2: 7.6.1, 7.8, 8.7.1,
9.1.2
Ensure EN54 compliance
for access to controls.