Notifier AFP-2800 User manual

OPERATORS MANUAL
& INSTALLATION /PROGRAMMING MANUAL
AFP-2800
Fire Alarm Panel
Revision 1.2
October 30, 2001
Approvals:
Australian Standard AS4428.1 1999
SSL Approval No XF1769/R2
SSL Accredited
NSW (Head Office)
7 Columbia Court
Norwest Business Park
Baulkham Hills NSW 2153
Ph: [phone]
Fax: [phone]
Queensland
24 Potts Street
East Brisbane
QLD 4169
Ph: [phone]
Fax: [phone]
Victoria
32 Lambert Street
Richmond
VIC 3121
Ph: [phone]
Fax: [phone]
www.PDF-Zoo.com
firealarmresources.com

Page 2 AFP-2800 - Fire Indicator Panel – Emergency Operators Guide
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
SECTION 1:
SECTION 1:SECTION 1:
SECTION 1: EMERGENCY OPERATORS GUIDE
Isolate Bells Press: EXT BELL ISOLATE
•EXT BELL ISOLATE LED will light
•The Bells & Buzzer will stop
•A subsequent alarm will restart the Buzzer but not the bells
•The bell isolate can be toggled by pressing the button a second time
Isolate Warning System Press: WARN SYS ISOLATE
•WARN SYS ISOLATE LED will light
•The warning system will stop
•A subsequent alarm will restart the Buzzer but not the warning
system
•The warning system isolate can by toggled by pressing the button a
second time
Acknowledging an Alarm Select the Alarm using the PREV , NEXT buttons
Press: ACK to acknowledge
•This will individually acknowledge alarms
•Once all alarms are acknowledged the alarm LED will go steady
Resetting an Alarm Select the Alarm using the PREV , NEXT buttons
Press: RESET then press ACK to confirm the resetting
•This will individually reset alarms
•Resets zone in alarm and clears all alarm outputs
•If alarm is still present, the zone(s) will re-alarm again after about 5
seconds
Isolate an Alarm Select the Alarm using the PREV , NEXT buttons
Press: ISOL then press ACK to confirm the isolation
Isolates the point in alarm and clears it’s alarm outputs
Isolating a zone automatically acknowledges the zone
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – Table Of Contents Page 3
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
SECTION 2:
SECTION 2:SECTION 2:
SECTION 2: TABLE OF CONTENTS:
SECTION 1:
SECTION 1:SECTION 1:
SECTION 1: EMERGENCY OPERATORS GUIDE...................................................................................2
SECTION 2:
SECTION 2:SECTION 2:
SECTION 2: TABLE OF CONTENTS: ..................................................................................................3
SECTION 3:
SECTION 3:SECTION 3:
SECTION 3: SYSTEM DESCRIPTION ..................................................................................................6
3.1 SPECIFICATIONS & APPROVALS: ..................................................................................................................7
3.2 APPROVALS INFORMATION ............................................................................................................................ 7
3.3 ELECTRICAL SPECIFICATIONS........................................................................................................................8
3.3.1 POWER SUPPLY ................................................................................................................................................. 8
3.3.2 CPU & TERMINATION BOARD.............................................................................................................................. 8
3.3.3 LCM/LEM FLASHSCAN

LOOP CONTROLLER MODULES ..................................................................................... 9
3.3.4 FAN CONTROL MODULE ....................................................................................................................................... 9
3.3.5 AZM 8.............................................................................................................................................................. 9
3.3.6 PAZM 8 (FUTURE RELEASE) .............................................................................................................................. 9
3.3.7 ACM-16AT .................................................................................................................................................... 10
3.3.8 ACM-32A....................................................................................................................................................... 10
3.3.9 SCS-8............................................................................................................................................................ 10
3.3.10 LDM-R32....................................................................................................................................................... 10
3.4 COMPATIBLE ADDRESSABLE DEVICES .........................................................................................................11
3.5 COMPATIBLE CONVENTIONAL DETECTORS...................................................................................................11
3.6 COMPATIBLE BATTERIES.............................................................................................................................12
3.7 SYSTEM CAPACITY AND EXPANDABILITY ......................................................................................................12
SECTION 4:
SECTION 4:SECTION 4:
SECTION 4: PANEL OPERATION .....................................................................................................14
4.1 FRONT PANEL DISPLAY...............................................................................................................................14
4.1.1 SELECTING SCREEN ITEMS................................................................................................................................14
4.1.2 ENTERING INFORMATION ................................................................................................................................... 15
4.1.3 SYSTEM COUNTERS.......................................................................................................................................... 15
4.1.4 POINT FORMATS............................................................................................................................................... 15
4.1.5 ANNUNCIATOR ADDRESSING.............................................................................................................................. 16
4.2 FIREFIGHTERS MODE ..................................................................................................................................17
4.3 SERVICE MENU MODE.................................................................................................................................18
4.3.1 SERVICE MENU STRUCTURE .............................................................................................................................. 18
4.3.2 SERVICE MENU ................................................................................................................................................ 20
4.3.3 SERVICE MENU - LIST....................................................................................................................................... 21
4.3.3.1 SERVICE MENU - LIST - ALARM ............................................................................................................................................................... 22
4.3.3.2 SERVICE MENU - LIST - FAULT ................................................................................................................................................................ 22
4.3.3.3 SERVICE MENU - LIST - ISOLATED ........................................................................................................................................................... 23
4.3.3.4 SERVICE MENU - LIST -ACTIVE ............................................................................................................................................................... 23
4.3.3.5 SERVICE MENU - LIST – ZONE ................................................................................................................................................................ 24
SERVICE MENU - LIST – ZONE - CHANGE............................................................................................................................................................ 24
4.3.3.6 SERVICE MENU - LIST - FLASHSCAN.................................................................................................................................................... 25
SERVICE MENU - LIST – FLASHSCAN- DETECTORS ......................................................................................................................................... 26
SERVICE MENU - LIST – FLASHSCAN– DETECTORS - STATUS................................................................................................................................................... 27
SERVICE MENU - LIST – FLASHSCAN– DETECTORS - CHANGE .................................................................................................................................................. 28
SERVICE MENU - LIST – FLASHSCAN- MODULES............................................................................................................................................. 29
SERVICE MENU - LIST – FLASHSCAN– MODULES - STATUS....................................................................................................................................................... 30
SERVICE MENU - LIST – FLASHSCAN– MODULES - CHANGE...................................................................................................................................................... 32
4.3.3.7 SERVICE MENU - LIST - RING .................................................................................................................................................................. 33
SERVICE MENU - LIST – RING – MODULE LIST .................................................................................................................................................... 33
SERVICE MENU - LIST – RING – MODULE LIST – MODULE I/O LIST................................................................................................................................................ 34
4.3.3.8 SERVICE MENU - LIST - AZF................................................................................................................................................................... 35
4.3.3.9 SERVICE MENU - LIST - DOUT ................................................................................................................................................................. 36
4.3.3.10 SERVICE MENU - LIST - DIN .................................................................................................................................................................... 37
4.3.3.11 SERVICE MENU - LIST - HISTORY ............................................................................................................................................................ 38
4.3.4 SERVICE MENU - ISOLATE ................................................................................................................................. 39
4.3.5 SERVICE MENU - CONFIG .................................................................................................................................. 40
4.3.5.1 SERVICE MENU – CONFIG – CHANGE ...................................................................................................................................................... 41
SERVICE MENU – CONFIG – CHANGE - AZF ....................................................................................................................................................... 42
SERVICE MENU – CONFIG – CHANGE – DOUT .................................................................................................................................................... 43
SERVICE MENU – CONFIG – CHANGE– DIN......................................................................................................................................................... 44
SERVICE MENU – CONFIG – CHANGE– FLASHSCANPOINT .............................................................................................................................. 44
4.3.5.2 SERVICE MENU – CONFIG – ISOLATE (PUSH BUTTON ISOLATES) .............................................................................................................. 46
4.3.5.3 SERVICE MENU – CONFIG – MODULE (ADD/ REMOVE) ............................................................................................................................. 47
4.3.6 SERVICE MENU – FLASHSCAN

....................................................................................................................... 48
4.3.6.1 SERVICE MENU – FLASHSCAN– LIST .................................................................................................................................................. 48
4.3.6.2 SERVICE MENU – FLASHSCAN– STATUS............................................................................................................................................. 48
4.3.6.3 SERVICE MENU – FLASHSCAN- PROGRAM.......................................................................................................................................... 48
4.3.6.4 SERVICE MENU – FLASHSCAN- DELETE ............................................................................................................................................. 49
4.3.6.5 SERVICE MENU – FLASHSCAN- LOOP UTILITIES .................................................................................................................................. 49
www.PDF-Zoo.com
firealarmresources.com

Page 4AFP-2800 - Fire Indicator Panel – Table Of Contents
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
4.3.7 SERVICE MENU - TEST ......................................................................................................................................50
4.3.7.1 SERVICE MENU – TEST - AZF .................................................................................................................................................................51
4.3.7.2 SERVICE MENU – TEST - DOUT ...............................................................................................................................................................52
4.3.7.3 SERVICE MENU – TEST - BATTERY ..........................................................................................................................................................52
4.3.8 SERVICE MENU - GLOBAL .................................................................................................................................53
4.3.8.1 SERVICE MENU – GLOBAL - SYSTEM........................................................................................................................................................54
4.3.8.2 SERVICE MENU – GLOBAL – FLASHSCAN.............................................................................................................................................55
4.3.8.3 SERVICE MENU – GLOBAL – SET DATE/TIME............................................................................................................................................55
4.3.8.4 SERVICE MENU – GLOBAL – DAY/NIGHT TIMERS ......................................................................................................................................56
4.3.8.5 SERVICE MENU – GLOBAL – PASSWORDS................................................................................................................................................56
4.3.9 SERVICE MENU - DIAGNOSTICS ..........................................................................................................................58
4.3.9.1 SERVICE MENU – DIAGNOSTICS - STATS ..................................................................................................................................................58
4.3.9.2 SERVICE MENU – DIAGNOSTICS - DBASE .................................................................................................................................................59
4.3.9.3 SERVICE MENU – DIAGNOSTICS - FLASH ..................................................................................................................................................59
4.3.9.4 SERVICE MENU – DIAGNOSTICS - RELAY..................................................................................................................................................59
4.3.9.5 SERVICE MENU – DIAGNOSTICS - XRELAY ...............................................................................................................................................59
4.3.9.6 SERVICE MENU – DIAGNOSTICS - LED.....................................................................................................................................................59
4.3.9.7 SERVICE MENU – DIAGNOSTICS – MODULE ..............................................................................................................................................59
4.3.9.8 SERVICE MENU – DIAGNOSTICS – LOCAL .................................................................................................................................................60
4.3.9.9 SERVICE MENU – DIAGNOSTICS – HISTORY..............................................................................................................................................60
4.3.9.10 SERVICE MENU – DIAGNOSTICS – RESTART THE SYSTEM.........................................................................................................................60
4.3.9.11 SERVICE MENU – DIAGNOSTICS – ERASE FLASH SECTORS.......................................................................................................................60
4.3.10 SERVICE MENU – LOG OFF.................................................................................................................................60
4.3.11 SERVICE MENU - PRINT.....................................................................................................................................61
SECTION 5:
SECTION 5:SECTION 5:
SECTION 5: APPENDIX: .................................................................................................................62
5.1 PLACING INTO OPERATION CHECKLIST.........................................................................................................62
5.1.1 PRE POWER-UP CHECKS. .................................................................................................................................62
5.1.2 POWER UP CHECKLIST......................................................................................................................................62
5.1.3 FAULT RECORD ................................................................................................................................................63
5.2 ZONE OPTION EXPLANATIONS......................................................................................................................64
5.2.1 AVF FUNCTIONAL DESCRIPTION .........................................................................................................................64
5.2.2 TIMED AZF FUNCTIONAL DESCRIPTION...............................................................................................................64
5.2.3 PAZM8 EOL VALUES (FUTURE RELEASE) .........................................................................................................64
5.3 ENTERING CONTROL SCRIPTS .....................................................................................................................65
Syntax Example...........................................................................................................................................................................................................................65
Syntax Meaning...........................................................................................................................................................................................................................65
5.3.1 USING ZONE NUMBERS IN SCRIPTS:.....................................................................................................................65
5.3.2 WRITING SCRIPTS .............................................................................................................................................66
5.3.3 SCRIPTING EXAMPLES .......................................................................................................................................66
5.3.4 MAKING AN OUTPUT LATCH. ...............................................................................................................................66
5.4 LCD-80 OPERATION ...................................................................................................................................67
Normal Operation........................................................................................................................................................................................................................67
Manual Operation........................................................................................................................................................................................................................67
Event Sounder.............................................................................................................................................................................................................................67
Display ........................................................................................................................................................................................................................................68
SPECIAL MESSAGES .....................................................................................................................................................................................................................68
NO RESPONSE FROM CPU ......................................................................................................................................................................................................68
5.5 RECOMMENDED CABLING REQUIREMENTS ...................................................................................................69
5.5.1 RS 485 COMMUNICATION’S CABLING.................................................................................................................69
5.5.2 ADDRESSABLE LOOP WIRING ............................................................................................................................69
5.6 PASSWORD ACCESS LEVELS .......................................................................................................................70
5.7 FLASHSCAN



DETECTOR SENSITIVITIES...................................................................................................71
5.8 PANEL CONNECTION DIAGRAMS: .................................................................................................................72
5.8.1 MAIN TERMINATION BOARD ...............................................................................................................................72
5.8.1.1 MAIN TERMINATION BOARD - CONNECTING RS485 FOR RING #1...............................................................................................................73
5.8.1.2 MAIN TERMINATION BOARD - CONNECTING 24VDC FOR RING #1 .............................................................................................................73
5.8.1.3 MAIN TERMINATION BOARD - CONNECTING AZF’S 1 &2 ............................................................................................................................73
5.8.1.4 MAIN TERMINATION BOARD - CONNECTING RELAY OUTPUTS .....................................................................................................................74
5.8.1.5 MAIN TERMINATION BOARD - PANEL EXPANSION RELAYS..........................................................................................................................74
5.8.2 CPU ...............................................................................................................................................................75
5.8.2.1 UPLOAD/DOWNLOAD PORT SETTINGS......................................................................................................................................................75
5.8.2.2 PRINTER PORT SETTINGS........................................................................................................................................................................75
5.8.3 RING EXPANDER MODULE .................................................................................................................................76
5.8.4 FLASHSCAN

LCM TERMINATIONS ...................................................................................................................77
5.9 BATTERY CALCULATIONS: ...........................................................................................................................80
5.9.1 QUIESCENT CURRENT CALCULATION: .................................................................................................................80
5.9.2 ALARM CURRENT CALCULATION: .......................................................................................................................80
5.9.3 BATTERY CAPACITY REQUIREMENTS ..................................................................................................................80
5.9.4 POWER SUPPLY CAPACITY REQUIREMENTS: .......................................................................................................80
5.10 FIELD REPLACEMENT PARTS: ......................................................................................................................81
5.11 FIELD MODULE CONNECTION DIAGRAMS......................................................................................................82
5.11.1 AZM-8 ............................................................................................................................................................82
5.11.2 PAZM-8..........................................................................................................................................................83
5.11.3 FAN CONTROLLER ...........................................................................................................................................84
5.12 ANNUNCIATOR CONNECTION DIAGRAMS .......................................................................................................85
5.12.1 ACM-16AT (16 BUTTONS, 32 LED’S) ..............................................................................................................85
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – Table Of Contents Page 5
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
5.12.2 ACM-32A (32 RED LED’S) ............................................................................................................................. 86
5.12.3 SCS-8 (8 FAN CONTROLS)...............................................................................................................................87
5.12.4 LDM-32 (EXPANSION RELAY DRIVER BOARD) ................................................................................................... 88
5.12.5 LDM-R32 (32 EXPANSION RELAYS) ................................................................................................................. 89
5.12.6 LCD-80 DISPLAY INTERFACE............................................................................................................................ 90
5.12.7 RS485 COMMS AND POWER CONNECTIONS (DETAIL) .......................................................................................... 91
5.13 PANEL EXPANSION RELAYS......................................................................................................................... 92
5.14 FLASHSCAN

DEVICES...............................................................................................................................93
5.14.1 DETECTOR BASES............................................................................................................................................ 93
5.14.2 FLASHSCAN

RELAY MODULE FRM-1.............................................................................................................. 94
5.14.3 FLASHSCAN

CONTROL MODULE FCM-1 ......................................................................................................... 95
5.14.4 FLASHSCAN

ZONE MODULE FZM-1................................................................................................................ 96
5.14.5 FLASHSCAN

MONITOR MODULE FMM-1 ......................................................................................................... 97
5.14.6 FLASHSCAN

MINI MONITOR MODULE FMM-101 .............................................................................................. 98
5.14.7 FLASHSCAN

XP5M (5 X MONITOR MODULE)................................................................................................... 99
5.14.8 FLASHSCAN

XP5C (5 X CONTROL MODULE)................................................................................................. 100
www.PDF-Zoo.com
firealarmresources.com

Page 6 AFP-2800 - Fire Indicator Panel – System Description
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
SECTION 3:
SECTION 3:SECTION 3:
SECTION 3: SYSTEM DESCRIPTION
The AFP2800 is a state-of-the-art microprocessor based distributed Fire Alarm Detection System. The panel
comprises multiple microprocessors for sharing the processing load both within the panel and in the field modules
using proprietary multiplexing communications, thus the term “distributed system”.
The main panel communicates with the intelligent field devices via RS485 communications rings. Each field
device can have multiple inputs and outputs. These inputs and outputs can include (but are not limited to) smoke
or heat detector circuits, bells and air conditioning controls.
The system supports two RS485 communications rings. Each ring can support up to 100 distributed field modules
and ring 1 can additionally support up to 99 panel annunciators and 30 LCD-80 units in terminal mode.
In addition to the two rings of distributed conventional communication, the panel can support up to 10 loops of
Notifier FlashScanAnalog /Addressable points. Each FlashScanloop can support 159 detectors and 159
modules.
In its maximum configuration, the panel can support up to 1602 Conventional Detection Circuits, more than 800
Programmable Relay Outputs and 3,180 Analog/Addressable FlashScanpoints.
All of this data is stored in a large database and text based scripts are continuously processed to implement the
logic of input and output functions similar to a programmable logic controller (PLC).
The system’s configuration data and event history is stored in non-volatile “Flash” memory, which does not rely on
battery power for its backup. The operating system is also stored in flash memory so there is no need for EPROM
changes to upgrade the firmware.
Ring
Interface
Module
Loop
Interface
Module
803
Up to 8 x 803 relay boards
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – System Description Page 7
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
3.1
3.13.1
3.1 S
SS
SPECIFICATIONS
PECIFICATIONSPECIFICATIONS
PECIFICATIONS & A
& A& A
& APPROVALS
PPROVALSPPROVALS
PPROVALS:
::
:
General Specifications:
Cabinet Zinc Sealed Steel 1.6mm
Powder Coated
Hinged Inner Door
Hinged Outer Door
AC Operational Voltage 240 VAC 50Hz + 10% Australian Version
Internal Power Supplies 24 VDC (nom) 3.0AMP (9.0 AMP optional)
Primary Microprocessor 68EC000
Memory Type Non-volatile 16Mbit Flash
Liquid Crystal Display Quarter VGA
Environmental Dry cold/heat: -10 Deg. C to +55 Deg. C
Damp heat: +40 Deg. C @ 93% Relative Humidity.
IP Rating IP 51
3.2
3.23.2
3.2 A
AA
APPROVALS
PPROVALSPPROVALS
PPROVALS I
II
INFORMATION
NFORMATIONNFORMATION
NFORMATION
Manufacturer: Notifier Inertia Pty Ltd
7 Columbia Court
Norwest Business park
NSW 2153 Australia
Phone: [phone]
Fax: [phone]
Product Name: Notifier Inertia AFP-2800 (formerly Notifier Inertia DFP-2800)
Approved to: AS4428.1 1999
Approval Document #: XF1769/R2
Issued By: Scientific Services Laboratory
Panel Serial #: ________________________
Date Of Manufacture: ________________________
www.PDF-Zoo.com
firealarmresources.com

Page 8 AFP-2800 - Fire Indicator Panel – System Description
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
3.3
3.33.3
3.3 E
EE
EL
LL
LECTRICAL
ECTRICALECTRICAL
ECTRICAL S
SS
SPECIFICATIONS
PECIFICATIONSPECIFICATIONS
PECIFICATIONS
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.1
11
1
1
11
1 P
PP
P
P
PP
PO
OO
O
O
OO
OW
WW
W
W
WW
WE
EE
E
E
EE
ER
RR
R
R
RR
R S
SS
S
S
SS
SU
UU
U
U
UU
UP
PP
P
P
PP
PP
PP
P
P
PP
PL
LL
L
L
LL
LY
YY
Y
Y
YY
Y
Parameter PS243 (3Amp Supply) PS249 (9Amp Supply)
Input Voltage 240 V AC +/- 10% 240 V AC +/- 10%
Input Range 216 V AC to 254 V AC 216 V AC to 254 V AC
Output Voltage 24 V DC nom. 24 V DC nom.
27.6 V DC no load 27.6 V DC no load
26.5 V DC full load 26.5 V DC full load
Adjustable Range 12 V DC to 30 V DC 12 V DC to 30 V DC
Rated Current Of Power Supply 3.0A @ 26.5 V DC 9.0A @ 26.5 V DC
Max Device Rating (electronic) 3.5A @ short circuit 9.5A @ short circuit
Overload Current Device 7.4A @ Short Circuit 20A @ Short Circuit
Secondary Transformer Fuse 5 A 15 A
Max Ripple 150 mV p-p 150 mV p-p
Load Regulation 2% 2%
Line Regulation 2% 2%
Temperature Coefficient 0.002V/°C 0.002V/°C
Efficiency >80% >80%
Switching Frequency 200 kHz 200 kHz
Battery Test Internal: 15 ohms Internal: 15 ohms
Battery Test Relay Contact Rating 10A 15A
Indicators Mains On, Output On Mains On, Output On
Status Indicators By External Interface or
FIP
By External Interface or
FIP
Environmental -10°C to +55°C Dry heat
+40°C @ 93% RH
-10°C to +55°C Dry heat
+40°C @ 93% RH
WARNING: Severe damage will result if the batteries are connected incorrectly.
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.2
22
2
2
22
2 C
CC
C
C
CC
CP
PP
P
P
PP
PU
UU
U
U
UU
U &
&&
&
&
&&
& T
TT
T
T
TT
TE
EE
E
E
EE
ER
RR
R
R
RR
RM
MM
M
M
MM
MI
II
I
I
II
IN
NN
N
N
NN
NA
AA
A
A
AA
AT
TT
T
T
TT
TI
II
I
I
II
IO
OO
O
O
OO
ON
NN
N
N
NN
N B
BB
B
B
BB
BO
OO
O
O
OO
OA
AA
A
A
AA
AR
RR
R
R
RR
RD
DD
D
D
DD
D
Supply Input
requirements
20 to 28V DC
55mA max (without CPU board or field loops connected)
210mA max (with CPU board, without field loops connected)
A
larm Inputs
T
wo conventional Alarm Zone inputs are provided, detecting
open circuit fault, short circuit fault, alarm, and normal. Each
input is monitored and requires a 4K7 (nom) EOL resistor.
Power Outputs
A
uxiliary Power Output 20-28V 1A max
24V DC & 5V DC Power to Ring Expander Boards
CPU power supply – 5V DC+/- 5% 3A
A
larm Outputs
4
x 1A monitored outputs
4
x ELV relay contact outputs
Communications Link EIA485 on dual ports
24V DC (nom) 2A Max
Note: Up to 200 field modules may be installed. Additional
auxiliary power supply(s) will be required, depending on the
number of field modules installed.
Indications LED indications on Relay Outputs and Fuses
Panel Expansion
Relays
Expansion for 64 x 1A ELV relay contact outputs via 8 serial
IFS-803 Relay Boards
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – System Description Page 9
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3 L
LL
L
L
LL
LC
CC
C
C
CC
CM
MM
M
M
MM
M/
//
/
/
//
/L
LL
L
L
LL
LE
EE
E
E
EE
EM
MM
M
M
MM
M F
FF
F
F
FF
FL
LL
L
L
LL
LA
AA
A
A
AA
AS
SS
S
S
SS
SH
HH
H
H
HH
HS
SS
S
S
SS
SC
CC
C
C
CC
CA
AA
A
A
AA
AN
NN
N
N
NN
N





L
LL
L
L
LL
LO
OO
O
O
OO
OO
OO
O
O
OO
OP
PP
P
P
PP
P C
CC
C
C
CC
CO
OO
O
O
OO
ON
NN
N
N
NN
NT
TT
T
T
TT
TR
RR
R
R
RR
RO
OO
O
O
OO
OL
LL
L
L
LL
LL
LL
L
L
LL
LE
EE
E
E
EE
ER
RR
R
R
RR
R M
MM
M
M
MM
MO
OO
O
O
OO
OD
DD
D
D
DD
DU
UU
U
U
UU
UL
LL
L
L
LL
LE
EE
E
E
EE
ES
SS
S
S
SS
S
Minimum Nominal Maximum
Operating voltage V DC 20.6 24 29
Loop communications voltage 15 24 32
Loop current limit mA 340 400 430
LCM/LEM Pair Q Current 140 200
Communications Link EIA485 on dual ports
LED Indications Green – Onboard 5VDC Supply OK
Amber – Ground Fault Detected
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.4
44
4
4
44
4 F
FF
F
F
FF
FA
AA
A
A
AA
AN
NN
N
N
NN
N C
CC
C
C
CC
CO
OO
O
O
OO
ON
NN
N
N
NN
NT
TT
T
T
TT
TR
RR
R
R
RR
RO
OO
O
O
OO
OL
LL
L
L
LL
L M
MM
M
M
MM
MO
OO
O
O
OO
OD
DD
D
D
DD
DU
UU
U
U
UU
UL
LL
L
L
LL
LE
EE
E
E
EE
E
Supply Input 20 to 28V DC
55mA max (no relays energised)
130mA max (all inputs and relays energised)
Inputs 3 x Opto Isolated
Outputs 3 x ELV relay contact outputs
Communications Link EIA485 on dual ports
Indications LED indications on: Inputs
Outputs
RX/TX
Power
Fault
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.5
55
5
5
55
5 A
AA
A
A
AA
AZ
ZZ
Z
Z
ZZ
ZM
MM
M
M
MM
M 8
88
8
8
88
8
Supply Input 20 to 28V DC
90mA max (no relays energised)
155mA max (all relays energised)
Inputs 8 conventional alarm inputs
Monitoring – Open Circuit
Short Circuit
Alarm
Fault
Outputs 4 x ELV relay contact outputs
Communications Link EIA485 on dual ports
Indications LED indications on: Outputs
RX/TX
Power
Fault
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.6
66
6
6
66
6 P
PP
P
P
PP
PA
AA
A
A
AA
AZ
ZZ
Z
Z
ZZ
ZM
MM
M
M
MM
M 8
88
8
8
88
8
(
((
(
(
((
(F
FF
F
F
FF
FU
UU
U
U
UU
UT
TT
T
T
TT
TU
UU
U
U
UU
UR
RR
R
R
RR
RE
EE
E
E
EE
E R
RR
R
R
RR
RE
EE
E
E
EE
EL
LL
L
L
LL
LE
EE
E
E
EE
EA
AA
A
A
AA
AS
SS
S
S
SS
SE
EE
E
E
EE
E)
))
)
)
))
)
Supply Input 20V to 28V DC
100mA max (no alarms)
Inputs 8 A/D Alarm zone Inputs
EOL Programmable from 1K5 to 5K6
Communications Link EIA485 on dual ports
Indications LED indications on: RX/TX
Power
Fault
www.PDF-Zoo.com
firealarmresources.com

Page 10 AFP-2800 - Fire Indicator Panel – System Description
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.7
77
7
7
77
7 A
AA
A
A
AA
AC
CC
C
C
CC
CM
MM
M
M
MM
M-
--
-
-
--
-1
11
1
1
11
16
66
6
6
66
6A
AA
A
A
AA
AT
TT
T
T
TT
T
Supply Input 20V to 28V DC
40mA Standby
56mA Alarm
Communications Link EIA485 multi-dropped
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.8
88
8
8
88
8 A
AA
A
A
AA
AC
CC
C
C
CC
CM
MM
M
M
MM
M-
--
-
-
--
-3
33
3
3
33
32
22
2
2
22
2A
AA
A
A
AA
A
Supply Input 20V to 28V DC
40mA Standby
56mA Alarm
Communications Link EIA485 multi-dropped
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.9
99
9
9
99
9 S
SS
S
S
SS
SC
CC
C
C
CC
CS
SS
S
S
SS
S-
--
-
-
--
-8
88
8
8
88
8
Supply Input 20V to 28V DC
33mA Standby
20mA max current per LED when LED ON
Communications Link EIA485 multi-dropped
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.1
11
1
1
11
10
00
0
0
00
0 L
LL
L
L
LL
LD
DD
D
D
DD
DM
MM
M
M
MM
M-
--
-
-
--
-R
RR
R
R
RR
R3
33
3
3
33
32
22
2
2
22
2
Supply Input 20V to 28V DC
40mA Standby
200mA Alarm (32 relays energised)
Communications Link EIA485 multi-dropped
Relay contacts 1Amp maximum current
3
33
3
3
33
3.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.1
11
1
1
11
11
11
1
1
11
1 L
LL
L
L
LL
LC
CC
C
C
CC
CD
DD
D
D
DD
D-
--
-
-
--
-8
88
8
8
88
80
00
0
0
00
0
Supply Input 20V to 28V DC
100mA Standby
100mA Alarm
Communications Link EIA485 multi-dropped
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – System Description Page 11
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
3.4
3.43.4
3.4 C
CC
COMPATIBLE
OMPATIBLEOMPATIBLE
OMPATIBLE A
AA
ADDRESSABLE
DDRESSABLEDDRESSABLE
DDRESSABLE D
DD
DEVICES
EVICESEVICES
EVICES
MAKE MODEL TYPE MODEL NUMBER
ANALOG ADDRESSABLE DETECTORS
Notifier – FlashScanThermal Fixed Temp FST-751
Notifier – FlashScanThermal Rate Of Rise
Notifier – FlashScanSmoke Photo-Optical FSP-751
Notifier – FlashScanSmoke Ionisation FSI-751
Notifier – FlashScanSmoke VIEW FSL-751
Notifier – FlashScanCombination Acclimate FAPT-751
ANALOG ADDRESSABLE MODULES
Notifier – FlashScanInput Module Conventional Zone Interface FZM-1
Notifier – FlashScanInput Module Monitor FMM-1
Notifier – FlashScanInput Module Mini Monitor FMM-101
Notifier – FlashScanOutput Module Relay FRM-1
Notifier – FlashScanOutput Module Control Output FCM-1
3.5
3.53.5
3.5 C
CC
COMPATIBLE
OMPATIBLEOMPATIBLE
OMPATIBLE C
CC
CONVENTIONAL
ONVENTIONALONVENTIONAL
ONVENTIONAL D
DD
DETECTORS
ETECTORSETECTORS
ETECTORS
MAKE MODEL TYPE MODEL NUMBER
System Sensor Thermal Type A 5451AUS
System Sensor Thermal Type B 4451AUS
System Sensor Smoke Photo-Optical 2151AUS
System Sensor Smoke Ionisation 1151AUS
Hochiki Thermal Type A DCD-A
Hochiki Thermal Type B DFJ-60B
Hochiki Thermal Type C DCD-C
Hochiki Thermal Type D DFJ-90D
Hochiki Thermal Cool Room Type B sealed DFG-60BLKJ
Hochiki Smoke Ionisation SIJ-ASN
Hochiki Smoke Photo Optical SLR-AS
Vision Systems VESDA E700 CONTACT DEVICE
Vision Systems VESDA E70D CONTACT DEVICE
Vision Systems VESDA LaserPLUS CONTACT DEVICE
www.PDF-Zoo.com
firealarmresources.com

Page 12 AFP-2800 - Fire Indicator Panel – System Description
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
3.6
3.63.6
3.6 C
CC
COMPATIBLE
OMPATIBLEOMPATIBLE
OMPATIBLE B
BB
BATTERIES
ATTERIESATTERIES
ATTERIES
In general, any Sealed Lead Acid Battery, or Wet Lead Acid Battery designed for stationary use is compatible with
the AFP2800 Fire Indicator Panel. Automotive batteries must not be used. The use of Nickel Cadmium batteries
is not recommended.
Manufacturer Type Number Voltage Capacity (Ah) Qty Required
Best and Best Sealed LA BP17-12 12 17 2
Best and Best Sealed LA BP24-12 12 24 2
Best and Best Sealed LA BP40-12 12 40 2
NOTE: The batteries could be seriously and permanently damaged if they are permitted to discharge below 20V DC when placed
in series.
3.7
3.73.7
3.7 S
SS
SYSTEM
YSTEMYSTEM
YSTEM C
CC
CAPACITY
APACITYAPACITY
APACITY A
AA
AND
NDND
ND E
EE
EXPANDABILITY
XPANDABILITYXPANDABILITY
XPANDABILITY
Base System
Item Description Notes
Communications Ring 1 RS485 communications ring to support
Up to 100 Field Modules
Up to 99 Annunciators
8 System Outputs Bell Output
Warning System Output
General Alarm Output
5 Additional programmable relay
outputs
Power Supply 3 Amp power supply and battery
charger
Fused 24VDC outputs
A larger power supply
will be required if total
module load exceeds
2.5A. Power supplies up
to 18A are available.
2 Local AZF’s AZF 1
AZF 2
2 RS232 comms ports Laptop interface
System event printer
Keyboard Interface PS2 QWERTY IBM PC keyboard
System Memory 7500 Named points
5000 Control scripts
4000 History events
System Expansion
Item Description Notes
Ring Expander –
Communications Ring 2
Second RS485 communications ring to
support
Up to an additional 100 Field Modules
Loop Interface Module –
FlashScan 
Ring expander module to
communicate with up to 5 x pairs of
Notifier LCM/LEM modules. ie: total of
10 loops of FlashScan.
Each loop of
FlashScansupports
159 Analog/Addressable
Detectors and 159
Addressable Modules
Panel Expansion Relays Up to an additional 8 IFS-803 8-way
relay boards can be added via the
panel serial relay port
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – System Description Page 13
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
FlashScanLoops
Item Description Notes
LCM FlashScanLoop Controller
Loops 1,3,5,7,9
Max 5 per system
LEM FlashScanLoop Controller
Loops 2,4,6,8,10
Max 5 per system, LEM
“piggybacks” onto LCM.
Annunciators
Item Description Notes
ACM32 Annunciator 32 Red LED
ACM16AT Annunciator 16 Pushbutton
16 Red LED
16 Yellow LED
SCS-8 Annunciator 8 x 3 Position switches
8 x Red LED
8 x Yellow LED
8 x Green LED
A maximum of 99
Annunciators can be
installed on
communication ring #1.
LDM-R32 Annunciator 32 x 1 Amp relay outputs
Field Modules
Item Description Notes
AZM-8 8 AZF inputs
4 Programmable Relay Outputs
PAZM-8 8 AZF Inputs with programmable end
of line resistor values (1k5 to 5K6)
Fan Controller 3 Inputs (Opto-isolated, not monitored)
3 Programmable outputs
A maximum of 100 field
modules can be installed
on communications ring
#1 and 100 on
communications ring #2.
On board power supply
accommodates for the
first 10 modules. Larger
power supplies and
separate feeds are
required for systems
with additional modules.
RS485 signal is
regenerated at each
field module.
Display Interfaces
Item Description Notes
LCD-80 Terminal mode display interface A maximum of 30
Display Interfaces can
be installed on
communications ring #1.
www.PDF-Zoo.com
firealarmresources.com

Page 14 AFP-2800 - Fire Indicator Panel – Panel Operation
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
SECTION 4:
SECTION 4:SECTION 4:
SECTION 4: PANEL OPERATION
4.1
4.14.1
4.1 F
FF
FRONT
RONTRONT
RONT P
PP
PANEL
ANELANEL
ANEL D
DD
DISPLAY
ISPLAYISPLAY
ISPLAY
The AFP2800 is fitted with a one quarter VGA resolution graphical LCD screen allowing ease of use for the
operator by displaying multiple lines of information. The AFP-2800 uses the concept of “hard” and “soft” buttons.
A “hard” button is one which is labelled with a fixed function ( e.g. EXT BELL ISOLATE ).The functions of these
buttons do not change.
A “soft” button is one of the five buttons along the bottom of the LCD display. The function of the button may
change depending on the screen being displayed at the time. To indicate the button function, its label is changed
by software, and displayed along the bottom line of the LCD as a pictorial representation of a button. Not all
buttons are shown on a screen, and the unlabelled buttons will have no effect if pressed.
Rather than having a cluttered front keypad fascia with letters numbers and function keys, the AFP-2800 accepts a
standard PC101 style keyboard plugged directly into the CPU to allow full QWERTY function accessibility for
programming and diagnostic test. This provides not only ease of operation but also a more secure environment as
it prevents unauthorised tampering of the system configuration.
The LCD display is used to display information about the status of the system, field devices, and programming
menus. The layout of the front keypad provides a “Fire-fighter's facility” in accordance with AS4428. The purpose
of this facility is to provide a uniform display for all fire alarm panels to assist Fire-fighters during a response. The
thick red border signifies the Fire-fighters area and provides alarm based functions for the Fire-fighter.
The mode select buttons (bottom right) will toggle the system in between Fire-fighters mode and the service menu
where routine service and diagnostic tests can be performed. If there are any active and unacknowledged alarms
on the system, the system will jump to and remain in Fire-fighters mode until all alarms are acknowledged or reset.
4
44
4
4
44
4.
..
.
.
..
.1
11
1
1
11
1.
..
.
.
..
.1
11
1
1
11
1 S
SS
S
S
SS
SE
EE
E
E
EE
EL
LL
L
L
LL
LE
EE
E
E
EE
EC
CC
C
C
CC
CT
TT
T
T
TT
TI
II
I
I
II
IN
NN
N
N
NN
NG
GG
G
G
GG
G S
SS
S
S
SS
SC
CC
C
C
CC
CR
RR
R
R
RR
RE
EE
E
E
EE
EE
EE
E
E
EE
EN
NN
N
N
NN
N I
II
I
I
II
IT
TT
T
T
TT
TE
EE
E
E
EE
EM
MM
M
M
MM
MS
SS
S
S
SS
S
Selecting a screen item may be done in two ways
1. On a screen where the functions are numbered (e.g. Service Menu screen), pressing the number in front of
the appropriate item will immediately select that item.
2. On a screen with UP/DOWN facility, pressing the UP or DOWN (or PREV / NEXT ) button will move
the highlighted cursor up or down the list. When the SELECT button is pressed, the highlighted item will then
be selected.
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – Panel Operation Page 15
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
4
44
4
4
44
4.
..
.
.
..
.1
11
1
1
11
1.
..
.
.
..
.2
22
2
2
22
2 E
EE
E
E
EE
EN
NN
N
N
NN
NT
TT
T
T
TT
TE
EE
E
E
EE
ER
RR
R
R
RR
RI
II
I
I
II
IN
NN
N
N
NN
NG
GG
G
G
GG
G I
II
I
I
II
IN
NN
N
N
NN
NF
FF
F
F
FF
FO
OO
O
O
OO
OR
RR
R
R
RR
RM
MM
M
M
MM
MA
AA
A
A
AA
AT
TT
T
T
TT
TI
II
I
I
II
IO
OO
O
O
OO
ON
NN
N
N
NN
N
On screens where character information needs to be entered, such as point labels, this must be done using an
external QWERTY style keyboard plugged into the PS2 keyboard plug on the rear of the CPU panel.
On screens (e.g. menus, change time/date) that require only numbers to be entered, can be entered directly with
the ten digit numeric keypad.
4
44
4
4
44
4.
..
.
.
..
.1
11
1
1
11
1.
..
.
.
..
.3
33
3
3
33
3 S
SS
S
S
SS
SY
YY
Y
Y
YY
YS
SS
S
S
SS
ST
TT
T
T
TT
TE
EE
E
E
EE
EM
MM
M
M
MM
M C
CC
C
C
CC
CO
OO
O
O
OO
OU
UU
U
U
UU
UN
NN
N
N
NN
NT
TT
T
T
TT
TE
EE
E
E
EE
ER
RR
R
R
RR
RS
SS
S
S
SS
S
On the top right hand side of all screens are the system counters showing the total number of
alarms, faults, isolates and non-alarm (supervisory) events on the system at any time. If a
device is both isolated and in fault it will increment both counters. For more information as to
which points are isolated, refer to the list menus.
4
44
4
4
44
4.
..
.
.
..
.1
11
1
1
11
1.
..
.
.
..
.4
44
4
4
44
4 P
PP
P
P
PP
PO
OO
O
O
OO
OI
II
I
I
II
IN
NN
N
N
NN
NT
TT
T
T
TT
T F
FF
F
F
FF
FO
OO
O
O
OO
OR
RR
R
R
RR
RM
MM
M
M
MM
MA
AA
A
A
AA
AT
TT
T
T
TT
TS
SS
S
S
SS
S
As the system is a database, all distributed points on field modules are controlled and referred to in “Ring, Module,
I/O format”. ie: Ring.Module.I/O - where I/O can consist of input, output or AZF.
Examples are as follows.
Point to be referred to Syntax
Ring 1, Module 1, Output 1 1.1.o1.
Ring 1, Module 20, AZF input 1 1.20.Z1
Ring 1, Module 30, input 1 1.30.i1
Ring 1, Annunciator 1 (module 101), Output 1 (led #1) 1.101.o1
Ring 1, Annunciator 99 (module 199), Input 1 (button #1) 1.199.i1
FlashScanLoop 1 Detector 1 L1D1
FlashScanLoop 1 Module 1 L1M1
System points will be displayed and can be referred to as follows:
Description Syntax Comments
On Board AZF’s 2 AZF’s on termination Board
AZF #1 0.1.z1 (Ring 0 Module 1, zone 1)
AZF #2 0.1.z2 (Ring 0 Module 1, zone 2)
Distributed Field Modules Up to 99 modules per ring
AZF 1.1.z1 8 AZF points per AZM8 or PAZM8
module
Din 1.1.i1 3 Din Per SCS-8 Module
Dout 1.1.o1 4 Dout Per AZM-8, 3 Dout Per SCS-8
Annunciator Up to 99 Annunciators on ring 1
Inputs 1.101.i1 16 Din per 16AT, 24 Din Per SCS-8
Outputs 1.101.o1 32 Dout Per 16AT, 24 Dout Per SCS-8,
32 Dout Per ACM32A
FlashScanDevices Up to 10 Loops
Detectors L1D1 159 Detectors Per Loop
Modules L1M1 159 Modules Per Loop
A = 2
F = 5
I = 10
N = 5
www.PDF-Zoo.com
firealarmresources.com

Page 16 AFP-2800 - Fire Indicator Panel – Panel Operation
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
System Parameters
Common Alarm CA
Common Fault CF
Common Isolate CI
Battery Fault BF
Charger Hi CH
Charger Low CL
Mains On MO
Ext. Bell Isolated BI
Warning System Isolated WI
4
44
4
4
44
4.
..
.
.
..
.1
11
1
1
11
1.
..
.
.
..
.5
55
5
5
55
5 A
AA
A
A
AA
AN
NN
N
N
NN
NN
NN
N
N
NN
NU
UU
U
U
UU
UN
NN
N
N
NN
NC
CC
C
C
CC
CI
II
I
I
II
IA
AA
A
A
AA
AT
TT
T
T
TT
TO
OO
O
O
OO
OR
RR
R
R
RR
R A
AA
A
A
AA
AD
DD
D
D
DD
DD
DD
D
D
DD
DR
RR
R
R
RR
RE
EE
E
E
EE
ES
SS
S
S
SS
SS
SS
S
S
SS
SI
II
I
I
II
IN
NN
N
N
NN
NG
GG
G
G
GG
G
The AFP-2800 can support up to 99 Annunciator devices on ring 1. There are 4 types of Annunciators that can be
used.
Type Description Suggested Use
ACM32A 32 Red LED Mimic panel
ACM16AT 16 Pushbuttons
16 Red LED
16 Amber LED
Output control & Isolate control
SCS-8 8 x 3 position switches
8 Red LED
8 Amber LED
8 Green LED
1 x pushbutton and Red LED for FTR
Fan Control for up to 8 fans.
LDM-R32 32 x 1 Amp relay outputs EWIS interface
As the Annunciators co-exist on the same RS485 ring as distributed field modules, the Annunciator addresses
have 100 added to them. i.e. An Annunciator set to address 1 is recognised as module address 101. Annunciators
are simply treated as digital inputs and digital outputs to the system. Each button press or switch position is
considered as an input, each LED is considered as an output.
Example1: If an ACM32A Annunciator is installed and addressed as #1. The last Red LED on it would be
referred to as 1.101.o32 using the “Ring.Module.I/O” format.
Example 2: If an ACM16AT was installed and addressed as #2. The first Pushbutton on it would be referred to as
1.102.i1 using the “Ring.Module.I/O” format.
Example 3: If an SCS-8 was installed and addressed as #3. The first switch in the “up” position would be referred
to as 1.103.i1 using the “Ring.Module.I/O” format.
Example 4: If an LDM-R32 Annunciator is installed and addressed as #4. The last relay on it would be referred to
as 1.104.o32 using the “Ring.Module.I/O” format.
Note: Please refer to Section 5.12 for more information on Annunciator addressing and settings.
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – Panel Operation Page 17
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
4.2
4.24.2
4.2 F
FF
FIREFIGHTERS
IREFIGHTERSIREFIGHTERS
IREFIGHTERS M
MM
MODE
ODEODE
ODE
Only the one screen is available in this mode. The “soft” buttons control the functions available.
This mode is automatically entered when any unacknowledged alarm is present, and until all alarms are
acknowledged or cleared, no other screen can be selected. The top right corner of the screen shows a quick
system status, giving the total alarms, faults, isolates and non-alarm events at that time.
AFP-2800 FIRE PANEL
01 OCT 1999 14:44:37
RESETACKNNEXTPREV ISOL
TIME TYPE STATUS NUMBER
10:43:35 SMOKE ALARM 1 OF 2
ZONE 23 PENTHOUSE
10:44:15 FIRE ALARM 2 OF 2
ZONE 22 STAIRWELL
A = 2
F = 0
I = 0
N = 0
The soft button functions for this screen operate as follows:
PREV Will scroll the cursor up the list to the previous item.
NEXT Will scroll the cursor down the list to the next item.
ACKN Will cause the alarm to be marked as acknowledged.
RESET
Will perform a point reset function on the currently highlighted alarm. As per AS4428, you
will be requested to press ACKN to confirm the reset. Any other button will abort the reset.
Once an alarm is reset, it will be removed from the screen, however if the alarm condition is
still present, it will re-alarm after a 5 second time out.
ISOL
Will perform a point isolate function on the currently highlighted alarm. As per AS4428, you
will be requested to press ACKN to confirm the isolate. Any other button will abort the
isolate. Once an alarm is isolated , it will be remain on the screen marked as an isolated
alarm and must be reset to clear from the alarm screen. Once an alarm is isolated, to
deisolate the alarm you must go through the service menu, isol/deisol function.
Note: If “group zones” for Firefighters display is selected for AS4428, the zone displayed in fire fighters mode may be a
collection of several points on the system. Resetting or isolating a zone will result in all the underlying points being
isolated or reset. To view, isolate or reset individual alarm points you must go to the Service Menu and list alarms.
www.PDF-Zoo.com
firealarmresources.com

Page 18 AFP-2800 - Fire Indicator Panel – Panel Operation
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
4.3
4.34.3
4.3 S
SS
SERVICE
ERVICEERVICE
ERVICE M
MM
MENU
ENUENU
ENU M
MM
MODE
ODEODE
ODE
4
44
4
4
44
4.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.1
11
1
1
11
1 S
SS
S
S
SS
SE
EE
E
E
EE
ER
RR
R
R
RR
RV
VV
V
V
VV
VI
II
I
I
II
IC
CC
C
C
CC
CE
EE
E
E
EE
E M
MM
M
M
MM
ME
EE
E
E
EE
EN
NN
N
N
NN
NU
UU
U
U
UU
U S
SS
S
S
SS
ST
TT
T
T
TT
TR
RR
R
R
RR
RU
UU
U
U
UU
UC
CC
C
C
CC
CT
TT
T
T
TT
TU
UU
U
U
UU
UR
RR
R
R
RR
RE
EE
E
E
EE
E
1) Alarm
2) Fault
3) Isolate
4) Active
1) Zone
2) FlashScan
3) Ring
4) AZF
5) Dout
6) Din
7) History
5) List
1) List
1) AZF List
2) Dout List
3) Din List
4) Zone List
5) Flashscan List
6) Range (Flashscan)
2) Isolate
1) AZF List 2) Dout List
3) Din List 4) FlashScan List
5) FS_PROG - FlashScan Point
1) Change
2) Isolate
3) Module
3) Config
1) List
2) Status
3) FS-Prog
4) FS-Del
5) FS-Loop
4) Flashscan
Service Menu
www.PDF-Zoo.com
firealarmresources.com

AFP-2800 - Fire Indicator Panel – Panel Operation Page 19
©NOTIFIER INERTIA PTY LTD,2001 WWW.INERTIA.COM.AU
1) AZF List
1) Alarm Test a Zone
1) AZF List
2) Fault Test a Zone
1) Dout List
3) Dout Test a Point
4) Battery Test
5) FS Alarm Test a FS Device
6) FS Flt Fault Test a FS Device
5) Test
1) System
2) Flashscan
3) Time
4) Day/ Night
5) Paswords
6) Global
1) Alarm List
2) Fault List
3) Isolate List
4) Active List
1) Alarm History 2) Fault History
3) Isolate History 4) Active History
5) History
5) History
6) Script
7) Flashscan
8) Ring Modules
7) Print
1) Stats
2) DBase
3) Flash
4) Relay
5) XRelay
6) LED
7) Module
8) Local
9) History
Restart The System
Erase Flash Sectors
8) Diag 9) Logoff
Service Menu
www.PDF-Zoo.com
firealarmresources.com

Page 20 AFP-2800 - Fire Indicator Panel – Panel Operation
© NOTIFIER INERTIA PTY LTD, 2001 WWW.INERTIA.COM.AU
4
44
4
4
44
4.
..
.
.
..
.3
33
3
3
33
3.
..
.
.
..
.2
22
2
2
22
2 S
SS
S
S
SS
SE
EE
E
E
EE
ER
RR
R
R
RR
RV
VV
V
V
VV
VI
II
I
I
II
IC
CC
C
C
CC
CE
EE
E
E
EE
E M
MM
M
M
MM
ME
EE
E
E
EE
EN
NN
N
N
NN
NU
UU
U
U
UU
U
This is the base level of service menu mode.
Screen functions such as the selection of a menu item may be selected in two ways.
1. By using the soft UP or DOWN buttons to scroll to the required item, then pressing SELECT or
2. By selecting the menu item number on the keypad.
The top right corner of the screen shows a quick system status, giving the total number of alarms, faults, isolates
and Non-Alarm events at any given time.
Pressing the SERVICE MENU button at any time will return you to this main menu screen
1) LIST LIST SYSTEM INFORMATION
2) ISOLATE ISOLATE MENU
3) CONFIG CONFIGURE POINTS
4) FLASHSCAN FLASHSCAN UTILITIES
5) TEST TEST MODULE FUNCTIONS
6) GLOBAL CONFIGURE GLOBAL PARAMETERS
7) DIAG VARIOUS DIAGNOSTIC TESTS
8) PRINT VARIOUS PRINTING UTILITIES
9) LOG-OFF RESET PASSWORD TIMER
SERVICE MENU
01 OCT 1999 14:44:37
SELECTDOWNUP MENU
USE BUTTONS/NUMBERS TO SELECT A FUNCTION
A = 0
F = 0
I = 0
N = 0
Action:
•Use UP and DOWN buttons to scroll through
options (or button 1to 9from keypad)
•Use SELECT to select the currently highlighted
option
www.PDF-Zoo.com
firealarmresources.com