Novacom V59 User manual

User's Guide of V59 TV Controller Board
V1.1
2014-04-09
ELECREALM
http://www.elecrealm.com/
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
1 / 28
Content
Chapter 1--LVDS Cable Connection ......................................... 2
Chapter 2--Voltage Jumper........................................................ 5
Chapter 3--Refresh firmware..................................................... 6
Chapter 4--Enter into Factory Mode and set LVDS Map number
................................................................................................ 11
Chapter 5--Mirror the image upside down............................... 18
Chapter 6--Change the input source via remote controller....... 20
Chapter 7--Change the input source via keyboard ................... 22
Chapter 8--Troubleshooting..................................................... 26
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
2 / 28
Chapter 1--LVDS Cable Connection
Please check the inserting condition of each foot. If some foot is not fully inserted (as
shown in the figure below), please use tweezers to press the exposure to the top of
the foot, let all feet be inserted into
well.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
3 / 28
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
4 / 28
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
5 / 28
Chapter 2--Voltage Jumper
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
6 / 28
Chapter 3--Refresh firmware
1. Please Prepare USB 2.0 Flash Memory Driver disk.
2. Please select the suitable firmware according to the resolution of your
LCD panel.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
7 / 28
3. Please copy the firmware to the USB 2.0 Flash Memory Driver disk.
Make sure it only has one firmware file that you need refresh.
4. Plug in USB 2.0 Flash Memory Driver disk to the USB port of
controller Board.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
8 / 28
5. Plug in 12V DC Power Supply.
6. Wait a moment. You will see the Led becomes red and then becomes
green. The Led will be flicker between red and green. The LED light
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
9 / 28
is always in the blue after finishing the refresh of the firmware.
7. Unplug the power supply from the driver board. Then connect the
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
10 / 28
LVDS cable and the LCD panel. Then plug the power to the power
input again. Turn on the power by keyboard or Remote controller.
8. Then you will see the controller board can work with the LCD panel.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
11 / 28
Chapter 4--Enter into Factory Mode and set
LVDS Map number
If the LCD panel displays the image as below, the LVDS map should
be changed. The operation only can be finished via the remote
controller.
1. Press the “menu” button on the remote controller.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
12 / 28
2. Then press number “1” “1” “4” “7” .
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
13 / 28
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
14 / 28
3. The LCD panel will display the following image:
4. Press “up/down” on the remote controller so that the cursor moves to
“LVDS Map”.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
15 / 28
5. Press “left/right--right” and go into LVDS Map. Then press
“left/right” and change the LVDS Map number to the proper number,
the LCD panel will go to the normal picture.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
16 / 28
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
17 / 28
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
18 / 28
Chapter 5--Mirror the image upside down
Please enter into “Factory setting” by referring to images in Chapter 4 first.
Then change the “MirrorEnable” value between “ON/OFF” by referring to the following images.
In order to rotate the image 180 degrees, please turn off the power and then turn on it after
changing “MirrorEnable” value from ON to OFF or from OFF to ON.
NOVACOM
NOVACOM

http://stores.ebay.com/elecrealm/
19 / 28
NOVACOM
NOVACOM