Novatek-electro PH-260t User manual

«NOVATEK-ELECTRO» Ltd
Intelligent industrial electronics
VOLTAGE RELAY
РН-260t
OPERATING MANUAL

Quality control system on the development and production complies with requirements
ISO 9001:2015
Dear customer,
Company NOVATEK-ELECTRO Ltd. thanks you for purchasing our devices.
You will be able to use properly the device after carefully studying the Operating Manual.
Keep the Operating Manual throughout the service life of the device.
Review the Operating manual before using the device
UKRAINE, Odessa www.novatek-electro.com

~ 2 ~
PH-260t NOVATEK-ELECTRO
ATTENTION! ALL REQUIREMENTS OF THIS OPERATING MANUAL ARE COMPULSORY TO BE MET!
WARNING! –DEVICE TERMINALS AND INTERNAL COMPONENTS ARE UNDER POTENTIALLY LETHAL
VOLTAGE.
TO ENSURE THE DEVICE SAFE OPERATION IT IS STRICTLY FORBIDDEN THE FOLLOWING:
TO CARRY OUT MOUNTING WORKS AND MAINTENANCE WITHOUT DISCONNECTING THE
DEVICE FROM THE MAINS;
TO OPEN AND REPAIR THE DEVICE INDEPENDENTLY;
TO OPERATE THE DEVICE WITH MECHANICAL DAMAGES OF THE CASE.
ATTENTION! THE DEVICE IS NOT INTENDED FOR LOAD COMMUTATION AT SHORT CIRCUITS.
THEREFORE, THE DEVICE SHOULD BE USED IN AN ELECTRICAL NETWORK PROTECTED BY AN
AUTOMATIC CIRCUIT BREAKER WITH A CUTOFF CURRENT OF MORE THAN 63 A, CLASS B.
IT IS NOT ALLOWEDWATER PENETRATION ON TERMINALS AND INTERNAL ELEMENTS OF THE DEVICE.
During operation and maintenance the regulatory document requirements must be met, namely:
–Regulations for Operation of Consumer Electrical Installations;
–Safety Rules for Operation of Consumer Electrical Installations;
–Occupational Safety when in Operation of Electrical Installations.
Installation, adjustment and maintenance of the device must be performed by qualified personnel having studied
this Operating Manual.
In compliance with the requirements of this Operating Manual and regulations the device is safe for use.
1–terminals for device connection;
2–button (UP) serves for navigation in the menu;
3–button (DOWN) serves for navigation in the menu;
4–button serves for entry to the menu;
5–a display;
6–a green indicator of load switching on (hereinafter in the text Load) is on, when the load is connected, it goes
down, when the load is off; it flashes when counting down the delay time of load disconnection;
7–a red indicator (hereinafter in the text –Fault) lights up when the load is off, it flashes when counting down the
delay time of load disconnection;
8–switch «Protection against recording»;
9–green indicator S [kVA] lights up when a total power value is displayed;
10 –green indicator P [kW] lights up when an active power value is displayed;
11 –green indicator Q [kVAr] lights up when a reactive power value is displayed;
12 –green indicator I[A] lights up when a load current value is displayed;
13 –green indicator U[V] lights up when a mains voltage value is displayed.
Figure 1 –Controls and overall dimensions of PH-260t

~ 3 ~
NOVATEK-ELECTRO РН-260t
This Operation Manual is intended to let you know about the device, safety requirements, operation and
maintenance procedures for the voltage-response relay PH-260t (hereinafter in the text: the device, PH-260t).
The device meets the requirements of the following:
EN 60947-1;
EN 60947-6-2; EN 55011; EN 61000-4-2.
Harmful substances, in more than allowed concentration, are not available.
Terms and abbreviations:
Controlled parameter –mains voltage and a parameter (variable) selected by the User (total power, active power,
reactive power, load current), with exceeding of which the device opens contacts 1-3 (Fig. 1);
AR –delay of automatic re-closure which is counted down after opening of contacts 1-3 (Fig. 1);
Display –a three-digit seven-segment indicator.
1 DESIGNATION
1.1. Designation of the device
The voltage relay PH-260t is designed to protect household and industrial electrical equipment (refrigerators, air
conditioners, washing machines, television, video and audio equipment, etc.) against unacceptable voltage
fluctuations in the mains and the effects of a neutral (zero) conductor breakage.
PH-260t indicates the actual value of the voltage in the mains and the state of the output contacts (the state of
the load).
PH-260t has protection against overheating due to exceeding of the rated current of the load.
PH-260t measures and displays current consumed by the load, active and reactive power and it trips off the load
in case of exceeding of the thresholds set for current and power.
The ranges of the parameters to be measured and controlled are shown in Table 1.
Table 1 –Ranges of the parameters to be measured and controlled
Name
Controlled range
Measured range
Total power, kVA
1 –14
0 –14
Active power, kW
1 –14
0 –14
Reactive power, kVAr
1 –14
0 –14
Load current, A
1 –63
0.5 –63
Input voltage, V
160 –280
120–350
PH-260t may be used as: a voltage-response relay; a consumed power limiting relay; a digital multimeter
(indication of the mains voltage, total, active and reactive power and current consumed).
PH-260t is supplied from the circuit that supplied the load.
1.2Controls and overall dimensions of the PH-260t:
Controls and overall dimensions are shown in Fig. 1.
1.3 Operation conditions
The device is designed for operation in the following conditions:
–Ambient temperature: from minus 35 to +55°C;
–Atmospheric pressure: from 84 to 106.7 kPa;
–Relative air humidity (at temperature of +25°C): 30 … 80%.
If the temperature of the device after transportation or storage differs from the environment temperature at
which it is expected to operate, then before connection to electric mains keep the device under the operating
conditions within two hours (because the device elements may have moisture condensation).
ATTENTION! The device is not intended for operation in the following conditions:
–Significant vibration and shocks;
–High humidity;
–Aggressive environment with content in the air of acids, alkalis, etc., as well as severe contaminations
(grease, oil, dust, etc.).
2 TECHNICAL SPECIFICATIONS
The main technical specifications of the device are shown in Table 2.
Characteristics of the output contacts of the device are shown in Table 3.
The defined parameters are given in Table 4.
Table 2 - The main technical specifications
Description
Value
Rated AC one-phase supply voltage, V
230/240
Mains frequency, Hz
47 –65
Harmonic composition (unsinusoidality) of the supply voltage
EN 50160
Rated insulation voltage, V
450

~ 4 ~
РН-260t NOVATEK-ELECTRO
Rated impulse withstand voltage, kV
2.5
Accuracy of total power measurement, %, not more
5
Accuracy of active power measurement, %, not more
5
Accuracy of reactive power measurement, %, not more
5
Accuracy of current measurement, %, not more
2,5
Accuracy of voltage measurement within the range of 120 –350 V, % not more
2
Automatic re-closure time, min.
1 − 580
Cutoff delay, s
1 –300
Automatic re-closure time by voltage, s
1 –900
Readiness time, s, not more
0.8
Maximal switching current at active load, A
63
Consumed power at unconnected load, W, not more
3
Maximal voltage at which operability is retained (acting value), V
450
Minimal voltage at which operability is retained (acting value), V
120
Fixed delay of cutoff by Umах, s
1
Fixed delay of cutoff by Umin, s
12
Fixed response time at voltage exceeding 430 V and pulse duration of more than 1.5 ms,
s, not more
0.05
Fixed response time (voltage protection is on) at voltage decrease below 60 V from the
set value in Umin or at voltage decrease below 145 V, s
0.12
Fixed response time (voltage protection is off) at voltage decrease below 120 V, s
0.12
Fixed response time at voltage increase by more than 30 V from the set value in Umах or
at voltage exceeding 285 V, s
0.12
Accuracy of determining operation threshold by voltage, V
3
Voltage hysteresis, V
5
Rated mode of operation
long
Degree of device protection
IP 10
Electric shock protection class
II
Climatic version
NF 3.1
Permissible pollution
II
Overvoltage category
II
Wire cross section for connecting to terminals, mm2
0.5 –16.0
The moment of tightening the screws of terminals, N*m
2±0.2
Mass, kg, not more
0.2
Overall dimensions, HxBxL, mm
93х52х64.5
Installation (wiring) of the article - standard 35 mm DIN rail
The article retains its operability in any position in the space
Material of the body frame - self-extinguishing plastic
---
At the mains voltage below 120 V and more than 350 V the value of voltage measured by the device is not
correct
Table 3 –Characteristics of PH-260t output contacts
Description
Value
Maximal current at voltage of ~230 V (сos = 1), А
63
Maximal power at closed contacts, kVA
14
Maximal switched power (сos = 0.4), kVA
1.4
Maximal permissible alternative current voltage, V
250
Service life: − mechanical, times, at least
− electrical, times, at least
500 th.
10 th.
Table 4 –Defined parameters of РН-260t
Items of menu and their
designation on the display
Parameter to adjust and the range of values
Default
settings

Controlled parameter
«» –total power; «» –reactive power;
«» –active power; «» –load current


Power
from 1 to 14 kW (kVA, kVAr)


Current
from 1 to 63 А


Delay time of load cutoff
from 1 to 300 s


AR time by the controlled
parameter
from 1 to 580 min.
If the value if more than 580 min –AR is prohibited «»


Voltage protection
«» –protection is on; «» –protection is off


Minimal voltage threshold
from 160 to 220 V


~ 5 ~
NOVATEK-ELECTRO PH-260t

Maximal voltage threshold
from 230 to 280 V


AR time by voltage
from 1 to 900 s


Displayed parameter by
default
«» –total power; «» –consumed current;
«» –active power; «» –mains voltage.
«» –reactive power;


Parameter indication
mode
«» –parameter value is displayed continuously;
«» –parameter value is displayed for 15 seconds (then a
default parameter will be displayed);
«» –a continuous cyclic parameter displaying.


Password setting
allowable values from 000 to 999

3 THE INTENDED USE
3.1 Preparation for operation
3.1.1 Preparation for connection:
unpack and check the device for damage absence after transportation; in case of such damages
detection, contact the supplier or the manufacturer;
carefully study the Operation Manual;
If you have any questions regarding the installation of the device, please contact the manufacturer by
telephone number indicated at the end of this Operating Manual.
3.1.2 Connection
ATTENTION! ALL CONNECTIONS MUST BE PERFORMED WHEN THE DEVICE IS DE-ENERGIZED.
Error when performing the installation works may damage the device and connected devices.
To ensure reliability of electrical connections, flexible (multi-wire) conductors with voltage insulation for at least
450 V should be used. The wire cross section for connecting protected equipment depends on the load current
(power), and should be: for current of 40 A (9 kW) –at least 6 mm2; for current of 63 A (14 kW) - at least 10 mm2.
The ends of the wires must be stripped of insulation for 5 ± 0.5 mm and crimped with bushings. Fastening of the
wires should exclude mechanical damage, twisting and abrasion of wire insulation.
If necessary, it is allowed to use a wire with cross-section of 0.5 - 1 mm2for connection of supply to the
device (terminal 2, Fig. 1).
IT IS NOT ALLOWED TO LEAVE EXPOSED PORTIONS OF WIRE PROTRUDING BEYOND THE TERMINAL
BLOCK.
For a reliable contact, tighten the terminal screws with the force indicated in Table 2.
When reducing the tightening torque, the junction point is heated, the terminal block may be melted and wire can
burn. If you increase the tightening torque, it is possible to have thread failure of the terminal block screws or the
compression of the connected wire.
QF –a circuit breaker.
Figure 2 –Device connection diagram