Novus NVQ-4C User manual

USER`SMANUAL1.0
COLOR QUAD PROCESSOR
NVQ-4C
NOVUS SECURITY Sp. zo.o.
359 Pulawska Str., 02-801 Warsaw, Poland
tel: [phone]; fax: [phone]
[email protected]; www.novuscctv.com
© Copyright 2003, NOVUS SECURITY Sp.zo.o.

CCTV – NVQ-4C, color quad processor,user’s manual v.1.0
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved 2
FEATURES
Video Input
Connect up to 4 cameras.
Video Output
Quad and switch video output.
Real Time & High Resolution
Real time refresh rate (NTSC:30 frame/sec; PAL: 25 frame/sec.).
720(H) x 480(V) (NTSC) high resolution.
720(H) x 576 (V) (PAL).
16.7 million true color.
Multi-function
Independent full screen.
Auto sequential switching.
System auto detection (NTSC/PAL).
Video adjustable.
Friendly Design
User friendly operation.
SPECIFICATIONS
Video input port : 4 cameras
Video output port : 1 switch & 1 quad output
Load impedance : 75 Ohm
Power source : DC 12V ±10%
Power consumption : 6W maximum
Operating environment : 10~80%RH, 0oC~50oC
Dimension : 240(W) X 45 (H) X 150 (D) mm
Weight : 1250g
BACK PANEL CONNECTION
4321 VEDIO INPUT VIDEO OUTPUT
QUADSWITCH
500 mA
DC 12V
Figure 1-Back panel connection

CCTV – NVQ-4C, color quad processor,user’s manual v.1.0
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved 3
Video Input
Connect 4 cameras to video input ports
Video Output
1 Switch: Connect this output port to the video input of monitor or TV
2 Quad: Connect this output port to the video input of VCR
Power Jack
Connect to DC12V, 500mA power supply
OPERATION
Power On
After finishing the back panel connection, please plug in DC 12V adaptor for power on, then QUAD
light on.
Front Panel Operation
ENTER ESC
Figure 2 -Front panel keypads
Full Screen
Press any key of FULL SCREEN keys as , the FULL SCREEN LED light on, and the monitor
screen will display whole screen of the corresponding picture.
Quad
Press key, the QUAD LED light on, and the quad pictures will be displayed as following camera 1,
2, 3 and 4.
1
2
34
Figure 3 -Camera location of screen in quad mode
Switch
1. Press key and the screen will enter auto-switching mode. The Switch mode is switched from
QUAD screen to full screen, and dwell time is 3 seconds.
2. It will skip the blank channel automatically and only show you the active channels.

CCTV – NVQ-4C, color quad processor,user’s manual v.1.0
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved 4
System Set Up & Auto Detection
1. PAL system set up: Press +then power on. Please keep held two buttons more than 1
second for setting up PAL system internally.
2. NTSC system set up: Press +then power on Please keep held two buttons more than 1
second for setting up NTSC system internally.
3. Auto Detection: If you forgot to set up the system, this unit will detect the system from video
input 1 automatically during power on.
Video Adjustment
1. Press and hold ENTER key about 3 seconds then you will enter adjustment mode.
2. Press to select items.
3. Press + -to increase/decrease value (0~9).
4. Press ESCto skip this table.

All rights reserved © NOVUS SECURITY
NOVUS SECURITY Sp. z o.o.