Noyce Joyce RC MINIVAN User manual
RC
MINIVAN
Assemble carefully,
some components are fragile.
Follow the assembly instructions
thoroughly.
Avoid contact with water.
Not intended for repeated
assembling.
RC MINIVAN
The laminate model of the minibus is inspired by the VW Transporter
vehicle that has been manufactured for more than 60 years and is famous
especially from the times of the hippie movement. With this kit you
can build its functional model. No glue, soldering iron or other tools are
needed, all parts are simply broken out of the boards and assembled by
snapping together protrusions and holes. Characteristic round shapes
can be achieved by bending the laminate boards. At the end, all you
have to do is to insert 4 AAA batteries and your mobile minibus is born.
The boards are in several colors. There are always parts of the same color in each board.
ASSEMBLY
LIST OF COMPONENTS
1
3
4
5
6
7
8
9
11
12
13
16
17 18
20
21 22
26
33
34
36
40 42
43
46
50 53 55 56 45
51
48
44
39
19
13
1x electronics board
2x front wheel -(circumferential
and central part), F2 (circumferential and central part),
F3, F4 - three identical pieces, F5, F6, F7
2x rear wheel(circumferential
and central part), B2 (circumferential and central part),
B3, B4 - three identical pieces, B5, B6, B7
1x center frame
1x upper frame
1x front roof frame
1x rear roof frame
1x front lower part
1x rear lower part
1x side part
1x front upper part with windows
1x rear upper part with windows
1x door - left and right part
Roof
Roof
33
1x lower part of the front seat
1x front seat
1x front seat backrest
1x upper partition between the seats
1x center seat backrest
1x center seat
1x lower part of the center seat
1x back seat backrest
1x upper partition behind the backrest
1x rear seat
1x lower part of the rear seat
1x board for headlights
1x board for rear lights
1x table top
1x table leg
2x part for xing the front bumpers
Front bumper
the bumper parts together
Rear bumper
1x steering wheel
4x part per motor shaft
1x part on the rear protrusion of the motor
1x ring part for mounting the motor
CONNECTION
8x screw M 2.5
8x nuts M 2.5
2x screw M 2.5
2x lock nuts M 2.5
2x screw M 2 x 8
2x nuts M 2
4x wheel rubber
2x bearing
1x servo
1x wire for the servo
1x motor
1x carbon rod for steering wheel - 75 mm
1x front wheel mechanism
- right piece, left piece, middle piece
4x cover on the center of the wheel
2x shaft for rear wheel
1x logo
2x front light large
2x front light small
2x rear light
1.
5. 6.
2. 3.
4.
Screw together screws and nuts.
Screw the 3D printed cover to
Install the F4 parts - there are three
identical pieces.
Install parts F3, F2 and F1.
FRONT WHEELS ASSEMBLY
7.
Insert the wheels assembled in this way into the central
8.
9.
Screw the assembled front wheel mechanism to the chassis
10.
Insert the servo into the hole in part no. 20.
Tighten the screws no. 42 and nuts no. 43. Connect the servo connector to the
connector on the electronics board.
11. 12. 13.
Snap the assembly into the holes in
the electronics board.
through the hole in the center part of the front wheel mechanism.
electronics board.
14. 15.
Connect this front seat assembly to the relevant parts which are
already attached to the chassis.
1. 2.
FRONT SEAT ASSEMBLY
in the front of the chassis.
snap it into the holes in the backrest and chassis.
3. 4.
MOTOR ASSEMBLY
through it and then slide the part up to the protrusions on the plastic part of the motor.
1.
Snap the entire motor assembly into the holes in the electronics board. Connect the connector of the motor to the connector on the
electronics board.
2. 3.
REAR WHEELS ASSEMBLY
B5, B6 and B7 together.
side and screw them together and put the rubber band on the circumference
of the wheel.
1. 2.
REAR WHEELS AND BACK SEAT PLACEMENT
motor shaft.
1. 2.
it all into the backrest and electronics board. Snap the part with the
3. 4.
electronics board.
1. 2.
CENTER FRAME AND SIDES ASSEMBLY
3.
and electronics board.
Gently bend the front part around the frame and snap the relevant
protrusions of the center frame and electronics board into it.
4. 5.
the electronics board.
Gently bend the rear part around the frame and snap the relevant
protrusions of the center frame and the electronics board into it.
6. 7.
Table of contents
