manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. NTI
  6. •
  7. Water Heater
  8. •
  9. NTI Trinity Lx600 Guide

NTI Trinity Lx600 Guide

#84034 Trinity Lx Commercial Controller Issue date: 2012-Jan-11
Replacement Instructions Revision date: 2012-Jan-11
1/3
S:\NTI2001_N_Drive (1-20-09)\R&D\PARTS - ENGINEERING\Parts Department Stickers and Instructions\Current Parts Instructions (doc)\84034 instructions -
Trinity Lx Commercial Controller.doc
#84034 - Trinity Lx Commercial Controller Replacement Instructions
The commercial controller (part number 84034) is configured specifically for use with Trinity Lx
Commercial series boilers only, Lx500-800 inclusive. This controller shall NOT be used with
non Lx Commercial-series boilers. Use of this controller on boiler models other than Trinity Lx Commercial-series will
override some saftey features and may lead to unsafe operation resulting in fire, explosion, property damage or death.
Check the contents of the parts received to ensure the controller is labeled “84034 Sola,Lx
Comm. Cfg.”, signifying that it is for use with Lx Commercial-series Trinity boilers; see
illustration below. If the controller is not labeled, or has a different label, it is not intended for use with a Trinity Lx
Commercial-series boiler. Note: all commercial Sola controllers have a blue case, if the controller case is not blue return
to NTI.
Controller Replacement Instructions
The instuctions provided in this document are a supplement to the Installation and Operating
Instructions originally provided with the boiler. Failure to follow the Installation and Operating
Instructions may result in fire, explosion, property damage or loss of life.
These instructions describe the steps necessary to replace a controller from any model of the Trinity Lx Commercial
series, sizes 500 to 800 inclusive, with a “generic” controller. Be sure to thoroughly read and understand these
instructions before attempting a controller replacement.
Note: Before replacing an existing controller, record (if possible) the settings specific to the particular installation from
the old controller, so they may be transferred to the new replacement controller.
Replace the Trinity Lx Commercial controller:
1) Turn off power to the appliance via the circuit breaker, remote switch or local On/Off switch.
2) For Lx500-600 units remove the top panel. For Lx700-800 units, remove the top rear panel.
3) Remove the control panel cover.
4) Unplug all electrical connections from the controller. All wiring is connected to the controller by means of quick-
connect plugs, each of which is uniquely keyed to its mating receptacle to prevent incorrect electrical connections.
5) Remove the old controller from the panel. The controller is secured to the panel by four screws, #8 w/ ¼” hex drive.
6) Installation procedure is in reverse order.
7) Use the display to adjust the control parameter settings to the values specific to the boiler model (see instructions
below).
Contact NTI if the replacement
controller does not have this
exact decal on the Controller.
#84034 - Trinity Lx Commercial Controller Replacement Instructions
2/3
S:\NTI2001_N_Drive (1-20-09)\R&D\PARTS - ENGINEERING\Parts Department Stickers and Instructions\Current Parts Instructions (doc)\84034 instructions -
Trinity Lx Commercial Controller.doc
Control Settings Verification and Adjustments:
1) Control Configuration Verification –From the “Configuration” menu, select “System Identification and Access”.
Check to ensure the control is equipped with the correct configuration –see illustration below. Replacement
controllers intended for use on Lx Commercial-series boilers will begin with “NTI LxCGen”. At this time the
installer may choose to modify the “Boiler name” to reflect the boiler model the control is installed on, i.e. Lx500.
2) Modulation Rate Adjustments –Since the replacement control is generic to all Lx Commercial boiler models, the
minimum and maximum modulation rates must be set to the applicable values. Select “Modulation Configuration”
from the “Configuration” menu and adjust the settings according to the following table:
Parameter
Description
Settings
CH max. modulation
rate
Maximum permissible blower speed during CH demand. Setting
is model dependent.
Lx500 = 6400 rpm
Lx600 = 4350 rpm
Lx700 = 4300 rpm
Lx800 = 5300 rpm
DHW max.
modulation rate
Maximum permissible blower speed during DHW demand.
Setting is model dependent.
Minimum modulation
rate
Minimum permissible blower speed. Setting is model dependent.
Lx500 = 1400 rpm
Lx600 = 1050 rpm
Lx700 = 1250 rpm
Lx800 = 1250 rpm
Failure to set the modulation rates appropriate to your specific boiler model according the
table above may result in fire, explosion, property damage or loss of life.
Configuration Identification
Must begin with “NTI LxCGen”
#84034 - Trinity Lx Commercial Controller Replacement Instructions
3/3
S:\NTI2001_N_Drive (1-20-09)\R&D\PARTS - ENGINEERING\Parts Department Stickers and Instructions\Current Parts Instructions (doc)\84034 instructions -
Trinity Lx Commercial Controller.doc
3) Pulses Per Revolution Adjustment –Since the replacement control is generic to all Lx Commercial boiler models,
the blower tachometer feedback “Pulses per revolution” setting must be set to the appropriate value for the specific
boiler. Select “Fan Configuration” from the “Configuration” menu and adjust the settings according to the following
table (see the illustration below):
Parameter
Description
Settings
Pulses per revolution
Number of feedback pulses produced for each revolution of the
combustion blower impeller.
Lx500 = 2
Lx600 = 3
Lx700 = 3
Lx800 = 3

This manual suits for next models

3

Other NTI Water Heater manuals

NTI Lx150-400 User manual

NTI

NTI Lx150-400 User manual

NTI Trin & Stor S Series User manual

NTI

NTI Trin & Stor S Series User manual

NTI Trin & Stor S40 User manual

NTI

NTI Trin & Stor S40 User manual

NTI Trinity Lx 300 User manual

NTI

NTI Trinity Lx 300 User manual

NTI S Series User manual

NTI

NTI S Series User manual

NTI Trin & Stor ST Series User manual

NTI

NTI Trin & Stor ST Series User manual

NTI GF 200 User manual

NTI

NTI GF 200 User manual

NTI COMPACT SERIES User manual

NTI

NTI COMPACT SERIES User manual

NTI Trinity Lx - WH Series User manual

NTI

NTI Trinity Lx - WH Series User manual

Popular Water Heater manuals by other brands

Kenmore POWER MISER 153.336151 owner's manual

Kenmore

Kenmore POWER MISER 153.336151 owner's manual

Rheem 31202519V Owner's guide and installation instructions

Rheem

Rheem 31202519V Owner's guide and installation instructions

CTC Union EcoZenith I 550 Installation and maintenance manual

CTC Union

CTC Union EcoZenith I 550 Installation and maintenance manual

Grant DuoWave Plus System Installation & user's instructions

Grant

Grant DuoWave Plus System Installation & user's instructions

Venus Domestic VDH 100 user manual

Venus

Venus Domestic VDH 100 user manual

Sony VPL-CX75 Operation instructions

Sony

Sony VPL-CX75 Operation instructions

STIEBEL ELTRON PSH 30 Si Instructions for use and installation

STIEBEL ELTRON

STIEBEL ELTRON PSH 30 Si Instructions for use and installation

ENKA MILKER 50 instruction manual

ENKA

ENKA MILKER 50 instruction manual

Lochinvar EcoShield SHW35-245CE Installation, commissioning & maintenance instructions

Lochinvar

Lochinvar EcoShield SHW35-245CE Installation, commissioning & maintenance instructions

Philips AWH1615/51 user manual

Philips

Philips AWH1615/51 user manual

Webasto Thermo Top E installation instructions

Webasto

Webasto Thermo Top E installation instructions

Rinnai Mains Pressure Cylinder Owner and installer guide

Rinnai

Rinnai Mains Pressure Cylinder Owner and installer guide

Wolf SEM-1 300 Assembly instructions

Wolf

Wolf SEM-1 300 Assembly instructions

Rubine IA Series Operation manual

Rubine

Rubine IA Series Operation manual

Froling TURBOMAT TM 150 operating instructions

Froling

Froling TURBOMAT TM 150 operating instructions

Applimo Edel AIR Installation and operating instructions

Applimo

Applimo Edel AIR Installation and operating instructions

Graf CARAT XL Installation and maintenance instructions

Graf

Graf CARAT XL Installation and maintenance instructions

Nibe BA-ST 9030-1FEDC Installation and operating manual

Nibe

Nibe BA-ST 9030-1FEDC Installation and operating manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.