NuPrime DAC-10H User manual

NuPrime
DAC-10H

1
FCC Notice - Declaration of Conformity Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment.
Changes or modifications made to this equipment, not expressly approved by us or parties authorized by us could
void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Notice for customers: The following information is only applicable to equipment sold in countries applying EU
Directives.
EU Declaration of Conformity
Hereby, NuPrime Audio, Inc. declares that this device is in compliance with the essential requirements
and other relevant provisions of Directive 2004/108/EC.
The manufacturer of this product is NuPrime Audio, Inc., 1712 Pioneer Ave. Ste 1817, Cheyenne, Wyoming 82001,
USA.
The Authorized Representative for EMC and product safety is NuPrime Audio, Inc., 1712 Pioneer Ave. Ste 1817,
Cheyenne, Wyoming 82001, USA.
For any service or guarantee matters please refer to the addresses given in separate service or guarantee
documents.
For customers in Europe
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other
European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the recycling
of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. The recycling of materials
will help to conserve natural resources. For more detailed information about recycling of this
product, please contact your local Civic Office, your household waste disposal service or the shop
where you purchased the product.

2
SAFETY INSTRUCTIONS
There are two categories of Safety Instructions included in this manual:
Product Warnings, (i.e., what must never be done to assure avoiding those hazards that could cause
bodily injury or property damage); and
User Directions (i.e., what must always be done to assure the safe use of your device).
The Safety Instructions contained in this manual have been categorized in accordance with the seriousness of the
potential hazards through the use of Signal Words. Those Signal Words, and their intended meanings, are as
follows:
DANGER: Indicates that a failure to observe the Safety Instructions could result in death or catastrophic bodily
injury.
WARNING: Indicates that a failure to observe the Safety Instructions could result in serious bodily injury.
CAUTION: Indicates that a failure to observe the Safety Instructions could result in minor bodily injury or property
damage.
NOTE: Designates important information that relates to activities and/or conditions that might result in loss of
data and/or damage to your device.
Safe Use and Operation of Your Device
This equipment emits stray RF energy and will interfere with the reception of signals by airborne electronic
navigational devices or medical devices. Do not operate this equipment near any sensitive medical devices.
WARNING: Use only grounded AC power cords.
Always immediately disconnect the power to the equipment in the event the device emits an unusual odor or
sound or generates smoke.
WARNING: Never attempt to disassemble, repair or make any modification to your device. Disassembly,
modification or any attempt at repair could cause bodily injury or property damage, as well as damage to the
device itself.
WARNING: Your device is not a toy. Never allow children to play with your device. Misuse, rough or improper
handling of your device by children could result in serious bodily injury for any of the enumerated safety warnings
in this manual. In addition, always keep all accessories and components out of the reach of small children as small
parts might present a choking hazard. Seek immediate medical attention if choking occurs or if any small part has
been swallowed.
CAUTION: Never raise the sound volume level too high when using your device with earphones. An excessive
sound volume level could cause damage to your hearing.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water.
Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign object gets
into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service
person for inspection and necessary repairs.
Read all the instructions before connecting or operating the component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and on the product itself. Follow all operating
instructions.
Do not use this unit near water.

3
You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit. Do not place the unit on
a bed, sofa, rug, or similar surface that could block the ventilation openings. If the unit is placed in a bookcase or
cabinet, there must be ventilation of the cabinet to allow proper cooling. Keep the component away from
radiators, heat registers, stoves, or any other appliance that produces heat.
The unit must be connected to a power supply only of the type and voltage specified on the rear panel.
Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent. Do
not modify the supplied cable.
Do not route the power cord where it will be crushed, pinched, bent, exposed to heat, or damaged in any way. Pay
particular attention to the power cord at the plug and where the cord exits the back of the unit.
The power cord should be unplugged from the wall outlet during a lightning storm or if the unit is to be left unused
for a long period of time.
Immediately stop using the component and have it inspected and/or serviced by a qualified service agency if:
The power supply cord or plug has been damaged.
Objects have fallen or liquid has been spilled into the unit.
The unit has been exposed to rain.
The unit shows signs of improper operation.
The unit has been dropped or damaged in any way.

4
Company Background
In 2005, NuForce invented an amplifier that utilizes self-oscillating switching principles in an
analog-based topology (US patent #7,221,216) as a significant departure from bulky Class
A/AB designs using tubes or transistors, and Class-D digital designs that convert signals into
digital data. Thanks in full measure to unique innovations, the NuForce Reference 9 amp
received the Power Amp of The Year 2005 award from The Absolute Sound, a prestigious
American audiophile magazine. Subsequent versions of the Reference 9 received similar
awards in Japan and France. In the years that follow, NuForce has grown to include a full line
of Mobility, Home Theater and Home Stereo products.
In 2014, having decided to focus on mobility products, NuForce sold the high-end line along
with its technology to investors who then created NuPrime Audio. Under the leadership of
NuForce co-founder and original CEO, NuPrime has assembled a design team comprised of
talented engineers who earlier worked on NuForce’s high-end line along with newly recruited
experts in switching-power circuit design. Recent developments have made it possible to
redesign NuPrime’s switching- amp topology from the ground up in order to create a new
generation of amps classified as Reference LE. The NuPrime DAC-10H is developed as a
Reference class Digital to Analog Converter for both the Reference and Reference LE class
amplifiers.
From Hi-Res to Extreme Resolution
High-volume storage has become cheap enough for the proliferation of hi-res music beyond
CD quality (16-bit/44.1kHz). Storing 24-bit/96 kHz or 192 kHz music with PCM encoding in
uncompressed format (typically WAV) or lossless compression format (such as FLAC, M4A,
WMA) has become standard practice for audio enthusiasts.
Music is typically recorded in 24 or 32-bit PCM or DSD format at the recording studio. It is then
converted to lower resolution format for mass-market distribution.
Pulse-code modulation (PCM) is a method used to digitally represent sampled analog signals.
It is the standard form of digital audio in computers, compact discs, digital telephony and other
digital audio applications. In a PCM stream, the amplitude of the analog signal is sampled
regularly at uniform intervals and each sample is quantized to the nearest value within a range
of digital steps. A PCM stream has two basic properties that determine the stream's fidelity to
the original analog signal: the sampling rate, which is the number of times per second that
samples are taken, and the bit depth, which determines the number of possible digital values
that can be used to represent each sample. DXD is simply PCM 24-bit/352.8 kHz.
Direct-Stream Digital (DSD) is the trademark name used by Sony and Philips for their system
of digitally recreating audible signals for the Super Audio CD (SACD). DSD uses pulse-density
modulation encoding –a technology to store audio signals on digital storage media that are
used for the SACD. The signal is stored as delta-sigma modulated digital audio, a sequence of

5
single-bit values at a sampling rate of 2.8224 MHz (64 times the CD Audio sampling rate
of 44.1 kHz, but only at 1⁄32768 of its 16-bit resolution).
Comparing PCM and DSD
The same music in DSD64 (2.8 MHz sampling rate) format takes up about 20% more storage
space than 24-bit/96kHz format. The NuPrime DAC-10H is designed to faithfully reproduce the
music irrespective of the format used.

6
The Ultimate Desktop DAC and Headphone Amp
Introduction
Following in a long tradition of award-winning excellence, the NuPrime DAC-10H combines
leading-edge technology that offers PCM 384K & DSD256 decoding with a high-power
balanced headphone amplifier. To excel beyond high performance DACs cluttering the
marketplace, NuPrime recognizes that merely supporting standard sampling rates and hi-res
music formats using state-of-the-art chips or proprietary digital signal processing is not
sufficient. To satisfy the most discerning audiophiles, the NuPrime DAC-10H must do three
things exceptionally well: 1) drive any headphones with ease; 2) deliver the utmost detail
during a symphony’s quietest passages or a soundtrack’s heart-pounding explosion; and 3) all
of this in the most natural sound. Simply put, the DAC-10H is a truly musical device.
A Reference LE Class Preamp
To meet the requirement of customers who want to eliminate extra components in their
system, a high-end preamp capable of driving the power amplifier directly is an essential part
of the design. The DAC-10H includes features borrowed from the Reference class P-20
preamp:
Advanced, thin-film switched-resistor ladder network for controlling volume, i.e., a
single resistor in the signal path at any volume setting.
Individually adjustable volume on each input for precise source level matching.
Volume adjustment in 99 precise, 0.5dB increments.
The Heart
As the heart of an audio system, the DAC-10H supports an extensive number of inputs and
formats. Utilizing the world’s best performing 32-bit audio DAC is only a first step for
designing the ultimate DAC. When state-of-the-art solutions are readily available to all
vendors, the experience and proprietary know-how in designing many Editor’s Choice and
Product of The Year award-winning products elevate the NuPrime DAC-10H above the
competition.
Several notable features:
Five digital and two stereo inputs for system flexibility.
SABRE32 Reference ES9018 from ESS Technology is the world’s best-performing 32-bit
audio DAC solution for high-end consumer applications and professional studio
equipment. With ESS’s 32-bit Hyperstream™ DAC architecture and Time Domain Jitter
Eliminator, the SABRE32 Reference DAC delivers an unprecedented dynamic range of
up to 135dB and THD+N (Total Harmonic Distortion plus Noise) of -120dB, all of which
put the DAC-10H at the industry’s cutting edge.

7
Symmetrical signal processing with exact signal transmission over the entire frequency
spectrum and extremely low harmonic distortion, ensuring an unadulterated musical
presentation.
Asynchronous transfer mode.
Ultra-low-noise JFETs in the input stage for the lowest possible noise level.
Supports DSD native playback by ASIO2.1 and DoP method.
Sample Rate Display –44.1, 48, 88.2, 96, 176.4, 192, 352.8, 384 kHz and DSD64 to
DSD256.
Unique dual gain settings for RCA with 2V or 4V outputs, XLR with 4V or 8V outputs;
and each of the balanced and unbalanced headphone outputs with four different high
power output settings.
Exclusive driver software for Windows.
Standard driver software for Mac.
Headphone Amplifier
Today’s best headphones can cost as much as a high-end DAC. Their owners demand a
headphone amp that fully exploits their potential. Key features of the headphone amp:
A 4-pin balanced and a standard 6.2mm stereo headphone amplifier outputs.
Output circuitry designed for use with up to two dynamic headphones. Consistent
wiring and the use of XLR-4 sockets ensure excellent channel separation.
A gain switch for use with in-ear, on-ear and over-ear headphones.
Other Features
Linear power supply with multi-rail toroidal transformer.
Independent left/right channel power supplies.
12V trigger output
Full microprocessor control with memory retention
Included remote control for full convenience.
Available in stylish black or silver anodized aluminum finish
The NuPrime Sound
Just one listen confirms the DAC-10H as a true hallmark of audio performance:
Vast soundstage
Lightning-fast, wide-range dynamics
Ultra-low distortion and noise
Music emerges from a pristine background, with delicate details and nuances intact.

8
Specifications
Inputs:
1 x USB Digital
2 x Coaxial Digital S/PDIF
2 x Optical Digital S/PDIF
2 x Analog Stereo RCA
Outputs:
Optical (up to 24 bit/192 kHz)
Stereo RCA (Line out)
Stereo Balanced (XLR-3 socket pre-out )
Balanced headphone amplifier (XLR-4 socket )
Unbalanced headphone amplifier (6.3 mm jack socket )
USB Sampling Rates: 44.1KHz, 48KHz, 88.2KHz, 96KHz, 176.4KHz, 192KHz, 352.8KHz,
384KHz and DSD 2.8MHz (DSD64) , 5.6MHz (DSD128) 11.2MHz (DSD256)
S/PDIF Sampling Rates: 44.1KHz, 48KHz, 88.2KHz, 96, 176.4KHz, 192KHz
Maximum Sampling Rate: 24-bits
Bit Resolution: 16-24-bits
Frequency Response: 10Hz to 80kHz
Max. output power: 680 mW @ 1 kHz and 600 ohm load at the XLR-4 output
Frequency response: < 10 Hz to > 100 kHz
Crosstalk attenuation: min. 93 dB @ 1 kHz
THD+N: < 0.0003%
Dynamic range: > 115 dB @ 600 ohm load (A-weighted)
Dimensions: Height: 24 inches (60.9 cm) Width: 14 inches (35.5 cm) Width: 14 inches
(35.5 cm)
Weight: 10.5 pounds ( 4.8 kg )
Worldwide AC voltage: (90VAC~130VAC // 210VAC~ 250VAC) With Voltage Select
Switch
AC Fuse: Slow-blow,T2.5A, 250VAC

9
Quick Start Guide
Front Panel View:
Power and Input Selector & Indicator:
Previous Channel
Power ON/OFF: Press 3 sec to turn ON. Standby light off, unit on.
Press 3 sec to turn OFF. Unit off, standby light on.
Next Channel
Input Indicator:
U: USB Digital Input
C: Coaxial Digital S/PDIF Input 1
O: Optical Digital S/PDIF Input 1
C: Coaxial Digital S/PDIF Input 2
O: Optical Digital S/PDIF Input 2
1: Analog Stereo RCA Input 1 (Line 1)
2: Analog Stereo RCA Input 2 (Line 2)
Volume:
Volume down. Press and hold for continuous decreasing.
Mute: Press once to mute the unit completely. Press and hold 3 sec to mute Pre-Out.
Headphone outputs remain functional.
Volume up. Press and hold for continuous increasing.
Press and hold both buttons 3 sec to activate/deactivate Theater-Mode.
During Theater-Mode volume adjustment is disabled. Volume is set at 0 db. Headphone
outputs are also disabled.

10
Display:
Sample Rate Display:
PCM: 44.1, 48, 88.2, 96, 176.4, 192, 352.8, 384
DSD: d 2.8, d 5.6, d11.2
Gain and Vol. Display:
Gain: HH, HL, LH, LL VOL: 00 ~ 99
Gain Table:
Brief explanation and sample table for Gain control setting:

11

12
Back Panel View:
Inputs:
USB: USB Digital Input
COAX1: Coaxial Digital S/PDIF Input 1
COAX2: Coaxial Digital S/PDIF Input 2
OPT1: Optical Digital S/PDIF Input 1
OPT2: Optical Digital S/PDIF Input 2
LINE1: Analog Stereo RCA Input 1
LINE2: Analog Stereo RCA Input 2
Outputs:
ANALOG OUT: Stereo RCA Output (Line out/Pre-out: Subwoofer compatible)
XLR Balanced Output
Trigger Out: Connecting to power amplifier (ST-10) enables power on by DAC-10H.
AC Inlet Voltage Selector
Make sure that the AC Voltage selector switch at the bottom of the unit is switched to the
appropriate voltage for your country. All DAC-10H are shipped with the switch set to 230V AC
in order to prevent accidental damage.
Turn ON the AC power switch at the rear of the unit. The DAC-10H will now be in standby
mode. Blue LED indicator lights up on the front panel.

13
Using the Remote Control:
Power.
Input Selector:
U: USB
C: COAX 1
C: COAX 2
O: OPT 1
O: OPT 2
L1/L2: Toggle between LINE1 and LINE 2.
Mute: Mute the music.
VOL+: Increase Volume.
VOL-: Decrease Volume.

14
NuPrime’s Limited Warranty and Limitation of Liabilities
ADDITIONAL RIGHTS
FOR CONSUMERS, WHO ARE COVERED BY CONSUMER PROTECTION LAWS OR REGULATIONS IN THEIR COUNTRY OF PURCHASE OR,
IF DIFFERENT, THEIR COUNTRY OF RESIDENCE, THE BENEFITS CONFERRED BY THIS WARRANTY ARE IN ADDITION TO ALL RIGHTS
AND REMEDIES CONVEYED BY SUCH CONSUMER PROTECTION LAWS AND REGULATIONS. THIS WARRANTY DOES NOT EXCLUDE,
LIMIT OR SUSPEND ANY RIGHTS OF CONSUMERS ARISING OUT OF NONCONFORMITY WITH A SALES CONTRACT. SOME COUNTRIES,
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY OR CONDITION MAY LAST, SO THE LIMITATIONS OR EXCLUSIONS
DESCRIBED BELOW MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS THAT VARY BY COUNTRY, STATE OR PROVINCE. THIS LIMITED WARRANTY IS GOVERNED BY AND CONSTRUED UNDER
THE LAWS OF THE COUNTRY IN WHICH THE PRODUCT PURCHASE TOOK PLACE.
LIMITED WARRANTY
For a period of TWO (2) YEARS from the date of retail purchase by the original end-user purchaser (“Warranty Period”), NuPrime warrants (in)
this product against defects in materials and workmanship, and (ii) that each Product, unmodified and under normal use and conditions, will
substantially comply with NuPrime’ applicable written technical documentation for the Product. NuPrime reserves the right to make
substitutions and modifications from time to time in the specifications of Products sold by NuPrime, provided that such substitutions or
modifications do not materially affect overall Product performance.
If a hardware defect exists and a valid claim is received within the Warranty Period, at its option and to the extent permitted by law, NuPrime
will (1) repair the hardware defect at no charge, using new or refurbished replacement parts, (2) exchange the product with a product that is
new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product, or (3)
refund the purchase price of the product. NuPrime may request that you replace defective parts with user-installable new or refurbished parts
that NuPrime provides in fulfillment of its warranty obligation. A replacement product/part assumes the remaining warranty of the original
product or ninety (90) days from the date of replacement or repair, whichever provides longer coverage for you. When a product or part is
exchanged, any replacement item becomes your property and the replaced item becomes NuPrime's property. When a refund is given, your
product becomes NuPrime's property.
OBTAINING WARRANTY SERVICE
If you purchased the product in the U.S., deliver the product, at your expense, to any NuPrime Service Center located in the U.S. If you
purchased the product outside of the U.S., deliver the product to any NuPrime Authorized Importer in the country where you purchased the
product. Be aware, however, that not all countries have NuPrime Authorized Service Providers (‘NASP’) and not all Authorized Service
Providers outside the country of purchase have all parts or replacement units for the product. If the product cannot be repaired or replaced in
the country it is in, it may need to be sent to a different country or returned to the country of purchase at your expense for repair or
replacement. If you seek service in a country that is not the country of original purchase, you will comply with all applicable import and export
laws and regulations and be responsible for all custom duties, V.A.T. and other associated taxes and charges. Where international service is
available, NuPrime may repair or exchange defective products and parts with comparable products and parts that comply with local
standards.
You can always deliver the product to NuPrime’s U.S. main service center for obtaining warranty service, however, you may have to pay for
return shipping cost.
NuPrime may send you user-installable new or refurbished replacement product or parts to enable you to service or exchange your own
product (“DIY Service”). Upon receipt of the replacement product or part, the original product or part becomes the property of NuPrime and
you agree to follow instructions, including, if required, arranging the return of original product or part to NuPrime in a timely manner.
When providing DIY Service requiring the return of the original product or part, NuPrime may require a credit card authorization as security for
the retail price of the replacement product or part and applicable shipping costs. If you follow instructions, NuPrime will cancel the credit card
authorization, so you will not be charged for the product or part and shipping costs. If you fail to return the replaced product or part as
instructed or the replaced product or part is not eligible for warranty service, NuPrime will charge the credit card for the authorized amount.
EXCLUSIONS AND LIMITATIONS
This Limited Warranty applies only to hardware products manufactured by or for NuPrime that can be identified by the "NuPrime" trademark,
trade name, or logo affixed to them. The Limited Warranty does not apply to any non-NuPrime hardware products or any accessories, even if
packaged or sold with NuPrime hardware. Non-NuPrime manufacturers, suppliers, may provide their own warranties. Other accessories
distributed by NuPrime under the NuPrime brand name are not covered under this Limited Warranty. This warranty does not apply: (a) to
damage caused by accident, abuse, misuse, misapplication, liquid contact, fire, earthquake, non-NuPrime products, or other external causes;
(b) to damage caused by service performed by anyone who is not a NASP; (c) to a product or a part that has been modified without the written
permission of NuPrime; (d) to consumable parts, such as batteries, or protective coatings designed to diminish over time unless failure has
occurred due to a defect in materials or workmanship; (e) to cosmetic damage, including but not limited to scratches, dents, and broken
plastic on ports; (f) to defects caused by normal wear and tear or otherwise due to the normal aging of the product; or (g) if any NuPrime serial
number has been removed or defaced.

15
Important: Do not open the hardware product. Opening the hardware product may cause damage that is not covered by this warranty. Only
NuPrime or a NASP should perform service on this hardware product.
THIS WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND
CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. NUPRIME SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IF NUPRIME CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY. No NuPrime reseller, agent, or employee is authorized to make any modification, extension, or addition to
this warranty.
NUPRIME IS NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH
OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS,
DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY, ANY COSTS OF RECOVERING,
REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH NUPRIME PRODUCTS, AND ANY FAILURE
TO MAINTAIN THE CONFIDENTIALITY OF DATA STORED ON THE PRODUCT. NUPRIME SPECIFICALLY DOES NOT REPRESENT THAT IT
WILL BE ABLE TO REPAIR ANY PRODUCT UNDER THIS WARRANTY OR MAKE A PRODUCT EXCHANGE WITHOUT RISK TO OR LOSS OF
PROGRAMS OR DATA.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitations on the
duration of implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary by state or province.
Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be
presented to obtain warranty service.
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
NUPRIME SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF
THIS WARRANTY.