NuTone RangeMaster RM53000 Series User manual

Broan-NuTone LLC. 926 West State Street, Hartford, WI 53027
NuTone, Inc. 4820RedBank Road,Cincinnati, OH45227
Broan-NuTone Canada, Inc. 1140TristarDrive, Mississauga, Ontario, L5T1H9
ENGLISH ................................2
FRANÇAIS ............................16
ESPAÑOL..............................30
RM53000
Series
99043478A

- 2 -
WARNING
TOREDUCE THE RISK OFFIRE, ELECTRIC SHOCK, ORINJURY TO PERSONS,
OBSERVETHE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number listed
in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and lock
service panel to prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely fasten a promi-
nent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified person(s) in
accordance with all applicable codes and standards, including fire-rated con-
struction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases through
the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow
the heating equipment manufacturer’s guidelines and safety standards such
as those published by the National Fire Protection Association (NFPA), and
the American Society for Heating, Refrigeration and Air Conditioning Engi-
neers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with any separate solid-state speed control device.
8. To reduce the risk of fire, use only metal ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE :
A. Never leave surface units unattended at high settings. Boilovers cause smok-
ing and greasy spillovers that may ignite. Heat oils slowly on low or medium
settings.
B. Always turn hood ON when cooking at high heat or when flambeing food (i.e.
Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should not be allowed to accumu-
late on fan or filter.
D. Use proper pan size. Always use cookware appropriate for the size of the
surface element.
!
INTENDED FOR DOMESTIC COOKING ONLY
!
READ AND SAVE THESE INSTRUCTIONS

- 3 -
!
CAUTION
1. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do
not vent exhaust air into spaces within walls or ceilings or into attics, crawl
spaces, or garages.
2. Take care when using cleaning agents or detergents.
3. Avoid using food products that produce flames under the Range Hood.
4. For general ventilating use only. Do not use to exhaust hazardous or explo-
sive materials and vapors.
5. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep
drywall spray, construction dust, etc. off power unit.
6. Your hood motor has a thermal overload which will automatically shut off the
motor if it becomes overheated. The motor will restart when it cools down. If
the motor continues to shut off and restart, have the hood serviced.
7. For best capture of cooking impurities, the bottom of the hood should be a
minimum of 24" and a maximum of 30" above the cooking surface. See “Install
Mounting Bracket” section for mounting restrictions.
8. Two installers are recommended because of the large size and weight of this hood.
9. This product is equipped with a thermostat which may start blower automati-
cally. To reduce the risk of injury and to prevent power from being switched on
accidentally, switch power off at service panel and lock or tag service panel.
10. Do not use the top of the hood as a shelf.
11. Please read specification label on product for further information and requirements.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP
GREASEFIRE,OBSERVETHEFOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then
turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UPA FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam
explosion will result.
4. Use an extinguisher ONLY if:
A.Youknowyou haveaClassABCextinguisherandyoualreadyknow howtooperateit.
B.Thefireissmallandcontainedintheareawhereitstarted.
C.Thefiredepartmentisbeingcalled.
D.Youcanfight the fire with your backto an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.

- 4 -
OPERATION
Controls
The hood is operated using the slide con-
trols under the bottom of the hood.
The light switch turns the lamps on and off.
The blower switch turns the blower on to
three speed settings:
0- OFF
1 - LOW SPEED
2 - MEDIUM SPEED
3 - HIGH SPEED
The pilotlamplightsupwhenevertheblower
is on.
HEAT SENTRY™
Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a
device that will turn on or speed up the blower if it senses excessive heat above the
cooking surface.
1. If blower is OFF - it turns blower ON to HIGH speed.
2. If blower is ON at a lower speed setting - it turns blower up to HIGH speed.
When the temperature level drops to normal, the blower will return to its original
setting.
WARNING: The HEAT SENTRY thermostat can start the blower even if the
hoodisturnedOFF.Whenthisoccurs,itis impossibletoturntheblower OFFwith
its switch. If you must stop the blower, do it from the main electrical panel.
HALOGEN BULBS
This range hood requires two halogen bulbs
(Type JC, 12Volt, 20 Watt Max, G-4 Base).
WARNING: Always switch off the electri-
cal supply before carrying out any operation
ontheappliance.
To change bulbs:
1. Loosen the ring nut by turning it counter-
clockwise.
2. Remove the bulb by pulling sideward (DO
NOTROTATE).
!
CAUTION: Bulb may be hot.
3.ReplacewithType JC, 12Volt,20WattMax,
G-4 Base halogen bulb. Do not touch re-
placement bulb with bare hands!
Do not use bulbs greater than 20 Watts.
Bulbsgreaterthan20Wattswillcausefuse
toopen.
LIGHT
SWITCH PILOT
LAMP BLOWER
SWITCH
RING NUT

- 5 -
FUSE REPLACEMENT
IF LIGHTS FAIL TO OPERATE, DISCON-
NECT POWER AT THE SERVICE EN-
TRANCE. CHECK THE FUSE AND RE-
PLACE IF NECESSARY.
1. Raise or remove the lower decorative flue.
2. Remove the cover from the fuse box.
3. Unscrew the cap from the fuse holder and
remove the fuse.
4. Replace the fuse with the same size and
amperage (5 x 20mm, 4 amp, 125 volt).
Do not use fuses greater than 4 amps.
Fuses greater than 4 amps may dam-
age the transformer.
5. Reinstall the fuse holder cap, fuse box
cover and flue.
6. Reconnect power at the service entrance.
MAINTENANCE
Proper maintenance of the Range Hood will
assure proper performance of the unit.
Grease Filters
The grease filters should be cleaned fre-
quently. Use a warm detergent solution.
Grease filters are dishwasher safe.
See “INSTALL FILTERS” section for removal
and installation instructions.
Non-Ducted Recirculation Filter
The non-ducted recirculation filter should be
changed every 6 months.
See “INSTALL FILTERS” section for removal
and installation instructions.
NON-DUCTED
RECIRCULATION
FILTER
FUSE
FUSE
BOX
DECORATIVE
FLUE
GREASEFILTERS

- 6 -
MAINTENANCE, CONT’D
HoodCleaning
Stainless steel is one of the easiest materials to keep clean. Occasional care will
help preserve its fine appearance.
Cleaning tips:
1. Hot water with soap or detergent is all that is usually needed.
2. Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth
to avoid water marks.
3. For discolorations or deposits that persist, use a non-scratching household
cleanser or stainless steel polishing powder with a little water and a soft cloth.
4. For stubborn cases, use a plastic scouring pad or soft bristle brush together
with cleanser and water. Rub lightly in direction of polishing lines or “grain” of
the stainless finish. Avoid using too much pressure which may mar the sur-
face.
5. DO NOT allow deposits to remain for long periods of time.
6. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may
adhere to the surface causing rust.
7. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds
to remain in contact with stainless steel for extended periods. Many of these
compounds contain chemicals which may be harmful. Rinse with water after
exposure and wipe dry with a clean cloth.
Painted surfaces should be cleaned with warm water and mild detergent only.

- 7 -
PREPARE THE HOOD
Unpack hood and check contents.
You should receive:
1 - Hood
1 - Decorative Flue Assembly
1 - Parts Bag :
1 - Mounting Bracket
1 - Discharge Collar
1 - Flue Mounting Bracket
8 - Mounting Screws (4.8 x 38mm Pan Head)
7 - Mounting Screws (3.9 x 9.5mm Pan Head)
2 - Bracket Screws (3.9 x 6 mm Flat Head)
8 - Drywall Anchors
1 - Installation Instructions
1 - Warranty Card
8 MOUNTING SCREWS
(4.8 x 38mm Pan Head)
MOUNTING
BRACKET
DISCHARGE
COLLAR
FLUE MOUNTING
BRACKET 8 DRYWALL
ANCHORS
7 MOUNTING
SCREWS (3.9 x 9.5mm
Pan Head)
DECORATIVE
FLUE
2 BRACKET SCREWS
(3.9 x 6mm Flat Head)

- 8 -
INSTALL ELECTRICAL
WARNING: Electrical wiring must be
done by a qualified person(s) in accor-
dance with all applicable codes and stan-
dards. This range hood must be prop-
erly grounded. Turn off electrical power
at service entrance before wiring.
1. Plan where the hood will be located above
thecooktop. Refertothe“INSTALLMOUNT-
ING BRACKET” section for hood mounting
height options.
2. Install a standard 2” x 4” wall outlet box and
3-blade 125 volt, 15Amp grounded recep-
tacle.
3. Mount the receptacle 18” to 22” above the
bottom of the hood.
4.Locatethereceptaclewithinboundaryshown
and off center of the ductwork (to allow for
power cord plug and flue clearance).
INSTALL THE DUCTWORK
(DUCTED HOODS ONLY)
!
CAUTION:Toreducetheriskof fire, use
onlymetalductwork.
1. Decide where the ductwork will run be-
tween the hood and the outside.
2.Astraight,shortductrunwillallow the hood
to perform most efficiently.
3. Long duct runs, elbows, and transitions will
reducetheperformanceofthehood.Useas
fewofthem as possible.Largerducting may
berequiredforbestperformancewithlonger
duct runs.
4.Installarooforwallcap.Connectroundmetal
ductworktocapandworkbacktowardshood
location. Use duct tape to seal the joints be-
tween ductwork sections.
CENTER LINE
OF HOOD AND
DUCT
24” TO 30” ABOVE
COOKING SURFACE
(See “INSTALL MOUNTING
BRACKET” section for
mounting restrictions)
HOOD
ROOF CAP
6”
ROUND DUCT
WALL
CAP
ROUND
ELBOW
6”
ADAPTER
DECORATIVE
FLUE

- 9 -
DRYWALL
INSTALL MOUNTING BRACKET
(DUCTED AND NON-DUCTED HOODS)
1. Construct wood wall framing that is flush
with interior surface of wall studs.
Make sure:
a) the framing is centered over installa-
tion location.
b) the height of the framing will allow the
mounting bracket to be secured to
the framing within the dimensions
shown.
2. After wall surface is finished, secure
mounting bracket to framing using dimen-
sions shown.
INSTALLFLUEMOUNTINGBRACKET
(DUCTED AND NON-DUCTED HOODS)
1. Assemble the flue mounting bracket, ad-
justing outside width as shown. See Fig-
ure 10.
2. Carefully center the mounting bracket di-
rectly over the range hood location.
3. Secure the bracket assembly to the ceil-
ing using (2) 3.9 x 6mm mounting screws
and drywall anchors. Make sure the
bracket is pushed into the corner, tight
against the wall and centered over the
hood.
FLUE MOUNTING
BRACKET 3.9 x 6mm
FLAT HEAD
BRACKET
SCREWS
FRAMING
BEHIND
WOODCROSSSUPPORT
BEHINDDRYWALL
CROSS
SUPPORT
NOTES:
1. Minimum hood distance above cooktop must not be less than 24”.
A maximum of 30” above the cooktop is highly recommended for best capture of cooking impurities.
Distances over 30” above the cooktop are at the installer’s and user’s discretion - providing that ceiling height
and flue length permit.
2. Requires optional 10-foot flue extension model RFX5304 (ducted) or RFXN5304 (non-ducted).

- 10 -
PREPARE THE HOOD
NOTE: On stainless steel hoods, carefully
remove the plastic protective film from all
exterior surfaces of the hood, decorative
flues, and filter trames prior to final instal-
lation.
(DUCTED HOODS ONLY)
1. Install the discharge collar into the duct
connector of the range hood.
2.Attach an adequate length of 6” round steel
ducting to the range hood duct connector.
3. Duct tape all joints to make them secure
and air tight.
4. Secure the electrical system plate to the
range hood with (2) mounting screws.
5. Carefully place the lower decorative flue
into the recessed area of the range hood
top.
6. Carefully slide the upper decorative flue
down inside the lower flue.
Note: On 8-foot ceilings the air vents on the
upper flue are concealed by installing the flue
with air vents down.
Note: On 9-foot ceilings the air vents on the
upper flue will be exposed after installation.
ROOMSWITH10-FOOTCEILINGS
Rooms with 10-foot ceilings require flue ex-
tension model RFX5304, available from your
local dealer.
7. Discard the upper flue supplied with the
product. Replace it with the flue extension
RFX5304.
DISCHARGE
COLLAR
6”
DIAMETER
DUCT
DUCT
CONNECTOR
3.9 x 9.5mm
SCREWS
ELECTRICAL
SYSTEM
PLATE
UPPER
FLUE
LOWER
FLUE
UPPER FLUE
VENTS
EXPOSED
(9 foot
ceiling)
UPPER FLUE
VENTS
CONCEALED
(8 foot
ceiling)