NUTRIBULLET RX NB-301 User manual

User guide.
®
LICUADORA
MARCA: NUTRIBULLET®
MODELO: NB-301
ESPECIFIACIONES ELECTRICAS: 120 V ~ 60Hz 1700W máx IPX0
HECHO EN: CHINA
• Lea cuidadosamente el manual antes de usar su aparato.
• Repase y guarde estas indicaciones.
• Conserve y guarde estas advertencias de seguridad para futura referencias.

32
ELECTRICAL SAFETY
When using any
electrical appliance,
basic safety
precautions should
always be observed,
including the
following:
• CAUTION! To avoid risk
of electric shock, never
immerse the cord, plug,
or motor base of the
nutribullet Rx in water.
• Do not use this product
with any type of adaptor
or voltage converter
device.
• The use of attachments
that are not
recommended or sold by
nutribullet may cause fire,
electric shock, or injury
and void the warranty.
• Use of adapters and
voltage converters
is considered an
unauthorized modification
of the product and as such
will void the warranty. Use
of this product in countries
with dierent electrical
specifications may
damage the product.
• Depress the Power Button
to OFF and unplug the
nutribullet Rx when it is
not in use. Make sure the
motor base is unplugged
before assembling,
disassembling, adding
additional parts, or
cleaning.
• If the supply cord is
damaged, it must
be replaced by the
manufacturer, its service
agent or similarly qualified
persons in order to avoid
a hazard.
• Do not pull, twist, or
damage the power cord.
Important safeguards &
cautionary information.
for your safety, carefully read all instructions
before operating your nutribulletRx®.
Save these instructions!
FOR HOUSEHOLD USE ONLY
!
• Do not modify the plug in
any way. Doing so will void
the warranty.
• CAUTION! Keep cord out
of reach of children. Do
not allow the cord to hang
over the side of the counter
or table.
• Do not allow cord to
touch hot surfaces,
including stove.
• Periodically inspect cord
and plug for damage. Do
not operate any appliance
with a damaged cord
or plug. If the appliance
malfunctions or is dropped
or damaged in any
manner, discontinue use.
Contact customer service
for assistance in obtaining
a replacement.
• Depress the blue
illuminated power
button to switch o the
appliance after each use.
Disconnect from the
power outlet before
changing accessories or
handling blades.
• Warning! Potential of
personal injury from
misuse. Take care when
handling the sharp cutting
blades, pouring hot soup
from the pitcher, and
during cleaning.
• This appliance is not
intended for use by
persons (including
children) with reduced
physical, sensory or
mental capabilities,
or lack of experience
and knowledge, unless
they have been given
supervision or instruction
concerning use of the
appliance by a person
responsible for their
safety.
• Children should be
supervised to ensure that
they do not play with the
appliance.
• CAUTION! In order to
avoid a hazard due to
inadvertent resetting
of the thermal cut-out,
this appliance must not be
supplied through
an external switching
device, such as a timer,
or connected to a circuit
that is regularly switched
on and o by the utility.
• Periodically inspect
all nutribullet Rx
®
components for damage
or wear that may impair
proper function or
present an electrical
hazard. Assure that
power cord and plug are

54
undamaged. Discontinue
use and replace cups or
souperblast pitcher if you
detect cracking, crazing,
cloudiness or damage to
the plastic. Assure that
the blades rotate freely
and that the gasket is
seated and undamaged.
Assure that motor base
switch actuators are
unobstructed, clean,
and depress easily.
Follow maintenance in
User Manual and never
operate your nutribullet
Rx
®
with damaged
components. If your
nutribullet Rx malfunctions
in any way, immediately
discontinue use and
contact nutribullet
customer service by
visiting:
www.nutribullet.mx .
WARNING: TO
AVOID PERSONAL
INJURY, NEVER BLEND
HOT INGREDIENTS
OR LIQUIDS IN ANY
UNVENTED BLENDING
CUP OR PITCHER WITH
LID!!
Heated ingredients
can pressurize sealed
containers when
agitated and violently
expel hot contents upon
opening. Always start the
blending process with
room temperature or
refrigerated ingredients
and liquids (21°C/70°F or
cooler).
Never operate for more
than one cycle at a time
to create a smoothie.
Blade friction from
repeated operation
can heat ingredients
and generate internal
pressure in the sealed
cups. If the blending cup
is warm to touch, allow
to cool. Slowly unscrew
the blade assembly
from the blending cup,
pointed away from your
face and body, to release
any residual pressure.
Pressure can cause the
blended contents to erupt
from the cup, resulting in
possible personal injury or
property damage.
Never blend carbonated
liquids or eervescing
ingredients (e.g.,
baking soda, baking
powder, yeast, etc.) In
an unvented sealed cup.
Pressure from released
gases can cause a sealed
blending cup to burst,
resulting in possible injury
or property damage.
Sugar in fruits and
vegetables can ferment
over time, releasing gases
and causing pressure
to build up in a sealed
blending cups. If you
will not consume your
smoothie immediately,
remove the blade,
attached the stay fresh
lid to the cup or cover
with plastic wrap, and
refrigerate. Never store
any blended mixture in
a sealed Blending cup
either unrefrigerated or
for any prolonged period
of time; contents will spoil
and ferment.
BLADE SAFETY
Blades are Sharp!
Handle Carefully.
Use care when handling
any blade. To avoid
laceration injury, do not
handle or touch any
blade edge.
To prevent leakage and
the possible separation
of components during
operation, properly align
and securely attach
(hand tighten) the blade
to a blending cup or
souperblast pitcher, and
check for leakage before
placing it on the motor
base and operating your
nutribullet Rx
®
.
Never Store any blade
in the motor base unless
attached to a cup or
pitcher. An exposed blade
can present a laceration
hazard.
VENTILATION
CAUTION!
Always operate the
nutribullet Rx®on
level surface, leaving
unobstructed space
beneath and around the
motor base to permit
proper air circulation.
Slots and openings
on the bottom of the
product are provided
for ventilation to ensure
reliable motor operation
and to prevent over-
heating. Warning: to
prevent fire hazard,
motor base openings
should be free of dust or
lint and never obstructed
with flammable
materials such as
WARNING!
WARNING! WARNING!WARNING!WARNING!
WARNING! WARNING!

76
newspapers, tablecloths,
napkins, dishtowels,
or place mats.
EXTRACTION SAFETY
PRECAUTIONS
The nutribulletRx®has two
modes, smoothie mode and
souperblast mode which
are further explained in the
“How It Works” section of
this manual. Carefully read
and follow all the safety
precautions, particularly
when operating the
nutribullet Rx
®
in
souperblast mode.
WARNING! NEVER LEAVE
THE NUTRIBULLET Rx
®
UNATTENDED WHILE IN USE!
CLOSE SUPERVISION IS
NECESSARY WHEN ANY
APPLIANCE IS USED BY OR
NEAR CHILDREN.
NEVER USE THE EXTRACTOR
BLADE TO BLEND WITHOUT
LIQUID AS DOING SO MAY
DAMAGE THE BLADE AND
MOTOR
• Never put your hands or
utensils near the moving
blade. Never use your
hands or utensils to depress
the activator buttons
while the nutribullet Rx
is plugged in.
• Blades are sharp! Handle
carefully. Use care while
handling the blades not to
touch the blade edges to
avoid laceration injury.
• Check gasket to make
sure it is completely seated
in the cross blade unit
before each use. Contact
customer service for
assistance if gasket is not
completely seated.
• We recommend replacing
your extractor blade every
6 months or as needed
for optimal performance.
To order a replacement
blade, simply visit:
www.nutribullet.mx .
• The nutribullet Rx®is not
intended for use on the
stove top. Do not place
the motor base or any
nutribullet®accessory on
the stove or microwave or
immerse in boiling water.
This may result in damage
to the accessory.
• Never blend carbonated
beverages. Built-up
pressure from released
gases can cause container
to burst, resulting in
possible injury.
• Do not put hot liquids in
unvented blending vessel
before blending. Start with
cool or room temperature
ingredients (21°C/70°F
or less). Soup will heat in
the souper pitcher during
the extraction process to
~65°C/150°F.
• Caution must be observed
if hot liquid is poured
into the product (food
processor or blender) as it
can be ejected out of the
appliance due to sudden
steaming.
• Do not run the nutribullet
Rx®with empty nutribullet
Rx®cups or soupblast
pitcher as this can damage
the unit.
• After blending ingredients
in the oversized or short
cup, remove the blade
assembly—allow the vessel
with it’s contents to settle
and to release any pressure
that may have built up
during the extraction
process. If you will not
consume it immediately,
use the stay fresh lid to
close the container and
refrigerate. Unscrew the
lid and release pressure
periodically if storing longer
than a few hours to release
any added pressure that
may have built up due to
fermentation.
• Never permit any blended
mixture to sit inside a cup
sealed with a blade base
without first releasing
the pressure.
• Do not allow smoothies
or souperblasts to sit for
long periods in a sealed
container by unscrewing
the lid and opening the
cup for a few moments.
The sugars in the fruit and
vegetables can ferment,
causing pressure to build
up and expand in the
vessel which can cause
ingredients to burst and
spray out when moved
or opened.
• Release pressure by
carefully unscrewing the
lid and opening the cup
for a few moments.
• Avoid contact with
moving parts.

98
• To reduce the risk of injury,
never place the blade
assembly on the motor
base without a cup or
pitcher properly attached.
• NEVER PUT THE
EXTRACTOR BLADE
ON THE MOTOR BASE
WITHOUT BEING
SECURELY ASSEMBLED
ONTO CUP FIRST.
• Always operate pitcher
with vented cover in place.
• Keep hands and utensils
away from the cutting
blade while chopping or
blending food to reduce
the risk of severe personal
injury or damage to the
device. A scraper may be
used, but only when the
blender is not running.
• To reduce the risk of injury,
make sure the blade base
is securely screwed onto
the cup before placing it
on the motor base and
operating the appliance.
• Do not use nutribullet Rx
®
outdoors.
• Do not blend hot liquids in
sealed oversized or short
nutribullet
®
cups.
EXTRACTING SMOOTHIES
nutribulletRx®IS
PROGRAMMED TO RUN
FOR 1 MINUTE DURING
SMOOTHIE MODE
(G-BUTTON WILL BE
GREEN).
• If motor base does not
shut o after 1 minute
during smoothie cycle, stop
it manually by depressing
the blue illuminated power
button, located 90˚ to the
left side of the n-Button
or simply lift cup o motor
base.
• To turn o the machine
at anytime during the
smoothie cycle (n-Button
will be green), depress
the power button, located
90˚ to the left side of
the n-Button or simply
lift the cup o the motor
base. If you press the
n-Button for 2 seconds
during extraction and
the light turns orange,
you are in souperblaster
mode. WARNING:
Never use sealed cups
in souperlaster mode!
Depress the power button,
located 90˚ to the left
side of the n-Button and
simply lift the cup o the
motor base to turn o the
unit. The light will stop
glowing, signifying power
is o. Always unplug
the motor base upon
completion of processing.
• Do not touch coupling
gear directly with hands
after smoothie mode! The
coupling gear in blade
base and motor base
will be hot!
• Do not run in smoothie
mode for more than
1 cycle without allowing
motor base to cool
between cycles.
• If additional extraction is
required after first cycle,
first remove cup and
allow motor base to shut
o completely. Wait 15
seconds before returning
cup to motor base to start
another cycle.
• If you have run 3 cycles,
with 15 second rest
periods between each,
allow the ingredients to
settle and the motor base
to cool for 2-3 minutes
before attempting another
cycle.
• If you have run more
than 5 cycles in total,
allow the machine to cool
down for 10 minutes to
prevent overheating and
damaging the unit.
• Motor base is equipped
with an internal thermal
breaker that shuts o
the motor base if the
unit overheats.
• If the motor base
overheats and shuts
o, unplug the motor
base and press the blue
illuminated power button,
located 90˚ to the left
of the n-Button and let
it cool for an hour or
more before attempting
to use it again. Motor
base will reset when the
unit is powered o and
the thermal breaker has
cooled down suciently.
• When making nut butters
or oil-based foods, due to
the consistency, the food
will process and then stick
to the sides of the pitcher.
It is best to process
these types of foods in
30 second increments.
To do this, simply lift the
pitcher o the motor base

1110
after 30 seconds. Before
placing back on motor
base, open pitcher as
needed to scrape down
the ingredients to the
center of the pitcher.
Place pitcher back on
motor base and continue
to process in 30 second
increments until desired
consistency is reached.
• To prevent leakage,
always align and hand-
tighten or use blade
remover to tighten the
blade to the nutribullet Rx
®
cup prior to inverting it
and placing the assembly
on to the motor base.
• To turn on the nutribullet
®
:
plug the motor base into
an electrical outlet. Press
the power button, located
90˚ to the left side of the
n-Button. This will cause
the power button glow
blue. Next, place the cup
blade-side-down onto
the motor base. This will
activate the nutribullet
Rx
®
’s smart technology
function, causing the
n-Button at the front of
the unit to glow green.
• Once activated, the unit
will run for 1 minute in
regular smoothie mode
before it automatically
turns o. The n-Button will
stop glowing green at the
end of the 1-minute cycle.
To turn o completely
before the cycle is
complete, either lift the
cup o of the base, or
press the power button,
located 90° to the left
side of the n-Button. The
power button will extend
from its recessed position
and the blue light will no
longer be lit, signifying the
power is o.
• In smoothie mode, you
will notice there are
2 phases within each
cycle. The motor will slow
down half way through
the cycle to allow the
ingredients to settle for
improved processing. It
will then power up again
to finish the cycle. This is
a normal function of the
nutribullet Rx.
• Turn the nutribullet Rx
®
o
after each use. Depress
the power button, located
90˚ to the left side of
the n-Button. The blue
light will stop glowing,
signifying power is o.
POWER OFF
INSTRUCTIONS
• To turn o the machine
at anytime during the
smoothie cycle (indicated
by the green glowing
n-Button), depress the
power button, located
90° to the left side of the
n-Button and simply
lift the cup o motor
base. When the vessel is
removed from the motor
base, only the green
n-Button light will turn
o. When the power o
button is pressed, the blue
light will turn o and the
blade will stop spinning.
To turn o machine at any
time during souperblast
mode (indicated by
the orange glowing
n-Button), press the
power o button, located
90˚ to the left side of the
n-Button and simply lift
the souperblast pitcher
o the motor base. When
the vessel is removed from
the motor base, only the
orange n-Button light will
turn o. When the power
o button is pressed, the
blue light will turn o
and the blade will stop
spinning. Always press the
power o button when
machine is not in use.
SAFETY WARNINGS
FOR EXTRACTING
SOUPS
Warning!: Only use the
vented souperblast pitcher
and two-piece lid while
operating the nutribullet
Rx
®
in souperblast mode.
The souperblast pitcher
is specially vented to
release pressure as the
soup mixture heats. Other
vessels are unvented and
may rupture and cause
personal injury if misused
in souperblast mode.
• To prevent overheating:
do not repeat souperblast
mode for the same
hot soup. If more heat
is required, place the
contents in a microwave-
safe container and
continue heating to
desired temperature. To
make a new soup, empty
old contents, add new
ingredients and wait 3-4
minutes before returning
the vessel to the motor
base to start a new
smart technology cycle.

1312
• To prevent overheating,
do not run the nutribullet
Rx in souperblast most
for more than 2 cycles
total without allowing
the motor base and
souperblast accessories
to cool for 30-60 minutes.
• If motor base does not
shut o after one (1)
7-minute cycle during
souperblast mode,
depress the power button,
located 90° to the left side
of the n-Button or simply
lift the souperblast pitcher
o of the motor base.
• Motor base is equipped
with an internal thermal
breaker that shuts o the
motor base when the unit
overheats. If the motor
base overheats and shuts
o, unplug the motor
base or press the power
button, located 90° to the
left of the n-Button and
let it cool for an hour or
more before attempting
to use it again. Motor
base will reset when the
unit is powered o and
the thermal breaker has
cooled down suciently.
HEAT CAUTIONS
• During souperblast mode,
the contents inside can
reach up to about 70°C /
150°F through the friction
of the rotating blade.
• Keep hands and other
exposed skin away from
the lid opening to prevent
possible burns during
souperblast mode.
• Do not remove the lid
during processing of
soup—ingredients will
become hot and may
splash out and cause
injury.
• Do not touch souperblast
pitcher directly with
hands after souperblast
mode! The souperblast
pitcher surface, blades
and coupling gear will
be hot!
• Always use appropriate
heat resistant pads on
the handle to hold the
souperblast pitcher and
to support the bottom of
the container.
• Carefully open
souperblast pitcher lid
after souperblast mode,
as escaping steam and
moisture may cause
scalding burns.
• Always attach blade to
souperblast pitcher and
hand tighten or use the
blade remover to tighten
the blade to prevent
leakage prior to adding
ingredients into the
pitcher.
• Never use the extractor
blade to blend without
liquid as doing so may
damage the blade or
motor.
• Do not use the
souperblast pitcher on the
motor base without the
black lid and clear vent
top in place when running
the nutribullet Rx®.
• To turn the nutribullet Rx®
on in souperblast mode
using smart technology,
plug the motor base
into an electrical outlet.
Press the power button,
located 90˚ to the left
side of the n-Button. The
power button will glow
blue, signifying the power
is on. Next, place the cup
blade-side-down onto
the motor base. This will
activate the nutribullet
Rx®’s smart technology
function, causing the
n-Button at the front of
the unit to glow green.
• Press the green n-Button
down for 2 seconds until
it glows orange. This will
indicate that souperblast
mode has begun. The unit
will run in souperblast
mode for about 7 minutes
before automatically
turning o. Once o,
simply lift the souperblast
pitcher o of the motor
base.
• The motor will run in
3 phases during the
7-minute cycle. It
will slow down twice
throughout the cycle to
allow the ingredients
to settle for improved
processing. This is a
normal function of the
nutribullet Rx.
• The contents inside can
reach up to about 70°C /
150°F through the friction
of the rotating blade.
• If you wish to process
your soup for less than
the programmed time,
you may simply lift o the
souperblast pitcher or
press the power button,
located 90˚ to the left
side of the n-Button.

1514
• Always allow it to come
to a complete stop prior
to adding additional
ingredients during the
processing period.
• Always depress the
power button when not
in use. The blue light will
stop glowing, signifying
the power is o. With an
internal thermal breaker
that shuts o the motor
base when the unit
overheats. If the motor
base overheats and shuts
o, unplug the motor
base and press the power
button, located 90° to the
left of the n-Button and
let it cool for an hour or
more before attempting
to use it again. motor
base will reset when the
unit is powered o and
the thermal breaker has
cooled down suciently.
CLEANING
SAFEGUARDS
• After making a smoothie
or souperblast, the
blade must be cleaned
immediately.
• Always unplug motor
base and depress the
power button prior to
cleaning, assembling or
disassembling.
• Never submerge the
motor base in water or
place it in the dishwasher.
Wipe o any debris
inside the motor base
immediately to keep it in
good working order.
• Do not wash the blades
in the dishwasher as
elevated temperatures
can damage gasket seals.
• Do not remove the rubber
liner inside the motor
base. To clean, unplug
first, then wipe with a
sponge moistened with
warm water.
• The nutribullet Rx
®
cups
can be washed in the
dishwasher and should be
washed on the top rack
of the dishwasher using
the normal (not sanitize)
cycle.
• The nutribullet Rx
®
cups
and blades should not
be emmersed in boiling
water for any reason as
this will warp the plastic
and damage gaskets.
• Blades are sharp! Use
care when cleaning
blades to avoid injury!
Rinse blades immediately
after each use to prevent
debris from drying
and sticking to blade
components. If necessary,
use included brush to
loosen any debris around
blades, gaskets and blade
housing threads with care.
• Handwash only with mild
dish soap and warm
water (not hot).
• Dry immediately.
• For tough debris, fill the
cup ½ full with room
temperature (not hot),
mild soapy water. Then,
simply twist on the blade,
pop it on the base and
give it a run for 30-45
seconds. Follow up with a
thorough brushing..
• When washing blades,
do not attempt to remove
the gasket ring. Simply
hand wash the blades in
warm, mild soapy water.
Attempted removal of the
gasket may permanently
damage the blade
configuration and cause
leakage. If in time a
gasket becomes loose or
damaged, please contact
customer service for a
replacement nutribullet
Rx
®
blade holder at:
www.nutribullet.mx .
STUBBORN CLEANUP
• If ingredients dry inside
the nutribullet Rx
®
cups
or souperblast pitcher,
make your cleanup a
snap by filling the cup
about 2/3 full with room
temperature soapy
water and screw on the
extractor blade and if
using the souperblast
pitcher, put on lids. Place
the cup assembly on the
nutribullet Rx
®
motor base
for about 20-30 seconds.
This will loosen the stuck
ingredients, and with a
light scrub and rinse in
warm water, you’ll be
all done.

1716
CLEANING THE
NUTRIBULLETRX®
MOTOR BASE
HERE’S HOW TO
CLEAN IT UP
STEP 1:
The most important thing is
to UNPLUG the motor base
before cleaning!
STEP 2:
Use a damp rag to wipe
down the inside and outside
of the motor base.
• NEVER SUBMERGE THE
MOTOR BASE IN WATER
OR PLACE IT IN THE
DISHWASHER.
• Never put your hands or
utensils near the moving
blade and never use your
hands or utensils to press
the activator buttons
down while the motor
base is plugged in.
HEAVY CLEANING:
• Should the inside of
the base become sticky
due to spillage you
may follow these
additional cleaning
instructions:
• UNPLUG the motor base
and depress the power
button BEFORE cleaning.
• Place the motor base on
a dish towel to catch any
liquid or debris.
• Create a diluted vinegar
and water solution using
1 TBSP of vinegar and
2 TBSPs of warm water.
Pour the solution into the
motor base where the
blade assembly would
sit during normal use.
• Immediately use a dish
brush to dislodge any
debris and wipe it out
with a damp cloth.
• The motor base is
constructed with a drain
tube to drain any liquid
debris safely through to
the dish towel without
damaging the inside
components.
Save these
instructions!
If you have any comments,
questions, or concerns,
please go to:
www.nutribullet.mx .
!
®

191818
1.3 l oversized cup
with pitcher lid
900 ml short cup
with lip ring
1 l souperblast pitcher
with 2-piece lid
motor base blade remover
What’s included.
1 stay-fresh
resealable lid
extractor blade
with cleaning brush