Nuvico Xcel NCT-5ML-OV2 User manual

Package
Overview
Installation
1
2
3
4
►Connecting Network Cable
* 1 It is recommended to install the security cap for outdoor installation.
*2 If the PoE switch is used to power the camera, DC12V power supply is not
required.
Warning and Caution
■If the product does not work properly, please contact your dealer or
the nearest service center. Never attempt to disassemble the camera
yourself. (We shall not be responsible for any problems caused by
unauthorized repair or maintenance.)
■Do not allow water or liquid intrusion into the camera.
■In the use of the product, you must be in strict compliance with the
electrical safety regulations of the nation and region. When the product is
mounted on wall or ceiling, the device shall be firmly fixed.
■Do not u se camera beyond specified voltage range.
■Do not drop the camera or subject it to physical shock.
■Do not directly touch the camera when installing.
■Avoid touching the camera lens.
■If cleaning is necessary, please use clean cloth to wipe it gently.
■Do not aim the camera at the sun or extra bright place.
■Do not place the camera in extremely hot, cold (the operating
temperature shall be -22˚F~140˚F), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■To avoid heat accumulation, good ventilation is required for operating
environment.
Camera Quick start guide
CD Plastic plug ×4
Drill template
Rubber plug Screwdriver
Tapping screws × 4
Ethernet connector Power connector
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
the camera in the dry environment. You'd better install back the lower
dome less than 4 hours after removing it. Do not remove the protection
film until finishing the installation.
① Attach the drill template to the place where you want to fix the camera
and then drill the screw holes and the cable hole on the wall according
to the drill template.
②Rotate the trim ring anticlockwise to remove it from the camera.
2
13
Security Cap
■Please read these instructions carefully before operating the unit
and keep it for further reference.
■All the examples and pictures used here are for reference only.
■The contents of this manual are subject to change without notice.
2.93
2.93
Trim ring
(in)
1 2
1
2
DC12V
NCT-5ML-OV2 Vandal Dome Camera
Quick Start Guide
①Loosen the nut from the main element.
②Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.
③Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
•Access Through Xcel IP Utility
In LAN, there are two ways to access the camera. 1. Access
Through Xcel IP Utility; 2. Direct Access Through Web Browser
①Make sure that the camera and the PC are connected to the local
network.
②Install the Xcel IP Utility from the CD and run it after installation.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.2 26.201
192.168.1 .2
192.168.1 .3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 226 . 201
255 . 255 . 255 . 0
192 . 168 . 226 . 1
i
Tip: Enter the adm inistrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:25 5.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Typ e IP Address Http Port Data Port Subnet
Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand. Modify
the IP address and gateway of the camera and make sure the network
address is in the same local network segment as the computer. Please
modify the IP address of your device according to the practical
situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
the plugin in the computer. Then enter the user name and password in the
login interface.
•Direct Access Through Web Browser
NCT-5ML-OV2450043001328 A0
The default username is admin; the default password is 123456.
③
④Route and connect the cables.
⑤Secure the camera to the wall with screws provided as shown
below.
Loosen the screws to open the lower dome.
Rotation 0°~355°
Pan 0°~355°
Rubber Plug
Lower dome
Tilt 0°~67°
⑥
the camera on a monitor and then adjust the camera according to the
figure below to get an optimum angle.
Three-axis adjustment. Before adjustment, view the image of
⑦
screws. Then put the trim ring onto the lower dome and then rotate it
clockwise until it is locked.
Install the lower dome back to the camera and fix it with the
Transparent Dome Maintenance
Transparent dome is an optical element which is made of plastics.
fingerprints on the dome will reduce the clarity of the image, please keep it clean in the
course of installing or using but do not directly touch or wipe it. If there is any dirt or
dust, please follow these cleaning tips to clean your dome camera.
As dirt, dust or
*
* If there is water or grease on the dome, please gently wipe off the water or grease with
a soft cloth. Then use another clean cloth with a little neutral detergent to wipe it
several times until it is clean. Finally, dry it with a soft cloth.
* If there are fingerprints on the dome, please use a clean cotton cloth or lens cleaning
wipe with a little neutral detergent to wipe it several times and then dry it with a soft
cloth.
If there is dust on the dome, please use a dry soft brush to gently brush it .
Tips
Login
Name：
Password：
Stream Type：
Language：
Remember me
admin
1920x1080 25fps
English
①Make sure that the camera and the PC are connected via LAN.
②Find the Xcel IP Utility from the CD and then install it in the
computer. After that, run the Xcel IP Utility.
③Modify the IP address and make sure the network address is in the
same local network segment as the computer.
④Open your web browser and enter the modified IP address in the
address bar to log in the web client. Follow directions to download the
plug-in in the computer. After that, enter the default user name and
password to log in.
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please enter the password of the administrator and click
“Modify” button to modify the settings.
The default password of the administrator is “123456”.
④Double-click the IP address and then the system will pop up the web
browser to connect the IP Camera. Follow directions to download and install