Nuvico Xcel NCT-4M-B31AF User manual

Package
Overview
Installation
1
2
3
4
2
13
* 1 It is recommended to install the water-proof cap for network cable connection.
*2 If the PoE network switch is used to connect the camera, DC12V power supply
is not required.
①Loosen the nut from the main element.
②Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
Thank you for purchasing our product. There may be several
technically incorrect places or printing errors in this manual.
The updates will be added into the new version of this manual.
We will readily improve or update the products or procedures
described in the manual. The content is subject to change
without notice.
Warning and Caution
■If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■Keep away from liquid while in use.
■In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■Do not use camera beyond specified voltage range.
■Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■Do not aim the camera at the sun or extra bright place.
■Do not place the camera in extremely hot, cold (the operating
temperature shall be -20˚C~50˚C), dusty or damp locations, and do
not expose it to high electromagnetism radiation.
■To avoid heat accumulation, good ventilation is required for
operating environment.
■A few parts of the device shall be replaced regularly according
to their average enduring time. Regular checking is recommended
for all users.
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
the camera in the dry environment. You'd better install back the lens
cover less than 4 hours after removing it.
①Drill the screw holes and the cable hole on the wall according to
the drill template.
②Route the cables and connect the relevant cables.
Camera Quick start guide
CD Water-proof cap Plastic plug ×4
Drill templateRubber plug
CVBS&DC
IN cables
Screwdriver
4 tapping screws PA4×25
1 machine screw PWM3×5
∅22.6
∅91.4
∅103
∅5
64.6mm
64.6mm
90°
Microphone Cable
Headphone Cable
TF Card Slot
Reset Hole
CVBS/DC IN port for testing
Alarm Input/Output
RS485 Cable
Network Cable
Power Cable
1
2
3
5
7
9
4
6
8
10
ALM-COM
ALM-NO
ALM-IN
ALM-GND
RS485T+
RS485T-
Network Cable
●Alarm Connection
Alarm Input: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port of the camera.
Alarm Output: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
NO and COM separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
●Connecting Network Cable
8
9
10
2
3
4
5
6
1
7
CVBS Cable
NCT-4M-B31AF Bullet Camera
Quick Start Guide

IE Network Connection
5
MENU
MENU
IPC
IPC
Network Cable Network Cable
Network Cable
Switch
Router Computer
Computer
●Access the camera through Xcel IP Utility
Here we take accessing IP camera via LAN for example. In LAN,
there are two ways to access. 1. Access through Xcel IP Utility;
2. Directly Access through IE Browser
①Make sure that the camera and the PC are well connected to the
LAN.
②Find the Xcel IP Utility from the CD and then install it in the computer.
After that, run the Xcel IP Utility as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the ad ministrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet
Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
⑤Tighten the fixed screws to finish the installation.
③Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 201
255 . 255 . 255 . 0
192 . 168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please input the password of the administrator and click
“Modify” button to modify the setting.
The default password of the administrator is “123456”.
④ Double-click the IP address and then the system will pop up the IE
browser to connect IP-CAM. IE browser will automatically download the
Active X control. After downloading, a login window will pop up.
Input the user name and password to login.
The default username is admin; the default password is 123456.
●Directly Access Through IE
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP:80
Subnet Mask: 255.255.255.0 Data Port:9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera
for the first time.
①Set the IP address of the PC and make sure the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click “Local Area Connection” to pop up
the following window. Select “Properties” and then select Internet
protocol according to the actual situation (for example: IPv4).
Next, click “Properties” button to set the network of the PC.
②Open the IE Browser and input the default address of IP-CAM
and confirm. The IE browser will download Active X control
automatically.
③After downloading Active X control, the login dialog box will
pop up.
④Input the default username and password and then enter to view.
NCT-4M-B31AF450043000435 A1
Fixed Screws
Rubber Plug
Mounting Base
④ Bracket adjustment. Before adjustment, preview the image of the
camera on a monitor and then loosen the fixed screws to adjust the view
angle of the camera.
Tilt 90°
Pan 360°
Rotate
360°
③Mount the rubber plug to the gap of the mounting base. Then
secure the mounting base with camera to the wall with screws.