NXP Semiconductors EVB9S08DZ60 User manual

User’s Manual
Demonstration Board
for Freescale
MC9S08DZ60
EVB9S08DZ60

EVB9S08DZ60
Evaluation Board
for Freescale
MC9S08DZ60
(64-Pin LQFP)
User’s Manual
Revision 1.0
Copyright © 2006 SofTec Microsystems®
DC01103

We want your feedback!
SofTec Microsystems is always on the look-out for new ways to improve its Products and
Services. For this reason feedback, comments, suggestions or criticisms, however small,
are always welcome.
Our policy at SofTec Microsystems is to comply with all applicable worldwide safety and
EMC/EMI regulations. Our products are certified to comply to the European New
Approach Directives and the CE mark is applied on all our products.
This product as shipped from the factory has been verified to meet with requirements
FCC as a CLASS A product.
This product is designed and intended for use as a development platform for hardware or
software in an educational or professional laboratory.
In a domestic environment, this product may cause radio interference in which case the
user may be required to take adequate prevention measures.
Attaching additional wiring to this product or modifying the product operation from the
factory default as shipped may effect its performance and cause interference with other
apparatus in the immediate vicinity. If such interference is detected, suitable mitigating
measures should be taken.
SofTec Microsystems
E-mail (general information): [e-mail]
E-mail (marketing department): [e-mail]
E-mail (technical support): [e-mail]
Web: http://www.softecmicro.com
Important
SofTec Microsystems reserves the right to make improvements to this product, its documentation and software routines,
without notice. Information in this manual is intended to be accurate and reliable. However, SofTec Microsystems assumes no
responsibility for its use; nor for any infringements of rights of third parties which may result from its use.
SOFTEC MICROSYSTEMS WILL NOT BE LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA, PROFITS, USE
OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF.
Trademarks
SofTec Microsystems is a registered trademark of SofTec Microsystems, Spa.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation.
PC is a registered trademark of International Business Machines Corporation.
Other products and company names listed are trademarks or trade names of their respective companies.

EVB9S08DZ60 User's Manual
Page 3
Contents
1Introduction 5
1.1 Overview 5
1.2 Package Contents 5
1.3 Supported Devices 5
1.4 Recommended Reading 5
2Hardware Features 7
2.1 Evaluation Board Features 7
3Software Setup 9
3.1 Overview 9
3.2 Host System Requirements 9
3.3 Installing CodeWarrior Development Studio 9
3.4 Installing SofTec Microsystems Additional Components 10
4Hardware Setup 11
4.1 First Connection 11
5Operating Modes 15
5.1 Overview 15
5.2 Standalone Mode 15
5.3 Host Mode 15
6Application Tutorial 17
6.1 Overview 17
6.2 Step-by-Step Tutorial 17
7Jumper and Connector Settings 19
7.1 Mother Board Jumpers 19
7.2 Daughter Board Jumpers 23
7.3 Connectors 24
8Troubleshooting 27
8.1 USB Driver Problems 27
8.2 Communication Problems between the PC and the Demo Board 27

EVB9S08DZ60 User's Manual
Page 5
1 Introduction
1.1 Overview
The EVB9S08DZ60 Evaluation Board has been designed for the evaluation, demonstration
and debugging of the Freescale MC9S08DZ60 microcontroller.
The EVB9S08DZ60 can be used as a standalone application, or via its built-in USB-to-BDM
interface.
1.2 Package Contents
The EVB9S08DZ60 package includes the following items:
 The EVB9S08DZ60 evaluation board;
 A USB cable;
 A universal, 12 V DC power supply;
 The SofTec Microsystems “System Software” CD-ROM;
 The CodeWarrior Development Studio CD-ROM;
 A Quick Start Guide sheet;
 This user’s manual.
1.3 Supported Devices
The EVB9S08DZ60 Evaluation Board supports the following devices:
 MC9S08DZ60.
1.4 Recommended Reading
 Freescale microcontroller-specific datasheets and application notes;
 EVB9S08DZ60 Schematic.

EVB9S08DZ60 User's Manual
Page 7
2 Hardware Features
2.1 Evaluation Board Features
The EVB9S08DZ60 board features:
1. An “MCU” section containing:
 A MC9S08DZ60 microcontroller (in 64-pin LQFP package, already programmed
with a demo application);
 A clock module, a crystal oscillator, and a connector for providing an external clock
source, together with jumpers to select the clock source;
 A BDM connector for in-circuit debugging/programming with an external
instrument;
 Four header connectors with all of the MCU signals.
2. A power supply section containing:
 A 12 V DC barrel input connector (2.1 mm);
 Two banana input connectors (12 V DC and GND);
 A power on/off switch.
3. A built-in “USB TO BDM INTERFACE” section which allows the host PC to
communicate with the microcontroller through a standard USB interface.
4. An “INPUTS” section containing:
 A Reset push-button;
 Four additional push-button;
 Two potentiometers;
 Eight dip-switches;
 A series of jumpers to connect/disconnect the above controls to/from the
microcontroller.
5. An “OUTPUTS” section containing ten LEDs together with the relative jumpers to
connect/disconnect them to/from the microcontroller.
6. A “CAN” section containing a CAN connector with two CAN transceivers (high speed
and single wire) together with a series of jumpers to select the CAN physical layer to be
used.

Hardware Features
Page 8
7. A “LIN” section containing two LIN connectors together with a LIN enable jumper and a
“WAKE” push-button.
8. An “RS-232” section containing two RS-232 connectors (although only one transceiver
is provided) together with a series of jumpers to set the RS-232 mode.
9. A “SERIAL SETTINGS” section containing two jumpers to select which transceiver (the
RS-232_0 or LIN) is connected to the microcontroller’s shared TXD1 and RXD1 serial
lines.
10. A prototype area.
1
2
3
4
5
67 8
9
10
The EVB9S08DZ60 Evaluation Board