OAKWORKS MEDICAL PRODUCTS Powerline Series User manual

www.oakworks.com · 717.235.6807
OAKWORKS®
Treatment Tables
USER MANUAL
Powerline Series
Backrest
Seychelle Series
Flat Top

© Copyright 2021
OAKWORKS®, Inc.
Printed in U.S.A.
All rights are reserved. No part
of this document may be
photocopied, reproduced or
translated to another language
without prior written consent
of OAKWORKS®, Inc.
OAKWORKS®is a registered
trademark of OAKWORKS®, Inc.
Notice
The information contained within
this document is subject to change
without notice and should not
be construed as a commitment by
OAKWORKS®, Inc.
OAKWORKS®, Inc. encourages
requests for technical specifica-
tions and the like documentation to
ensure accuracy. The appropriate
documentation is available upon
request.
OAKWORKS®, Inc. shall not be
liable for incidental or consequen-
tial damages in connection with or
arising out of the furnishing, per-
formance, or use of this document
and the program material which it
describes.

Product Use Description ............................................................................................. 1
Symbol Identification .................................................................................................. 1
Important Safety Instructions ....................................................................................... 1
Product Description & Photo
Powerline Series .............................................................................................. 2-3
Seychelle Series .............................................................................................. 4-5
Installation
Table Assembly................................................................................................... 6
Inset Shelf........................................................................................................... 6
Directions for Use
Paper Roll Holder Use........................................................................................ 7
Wave Backrest Use............................................................................................ 7
Table Extender................................................................................................... 7
QuickLock Face Rest ......................................................................................... 8
Cleaning & Disinfection
Recommended Cleaners/Disinfectants ............................................................... 9
Cleaning Process ............................................................................................... 9
Inspections ............................................................................................................... 10
Warranty Information ................................................................................................ 10
Model Number & Serial Number ............................................................................... 11
Specifications
Product Specifications ..................................................................................... 12
Environmental Conditions ................................................................................ 12
Contact Information .................................................................................... back cover
TABLE OF CONTENTS

PRODUCT USE DESCRIPTION / IMPORTANT SAFETY INSTRUCTIONS
1
CAUTION
READ AND SAVE THESE INSTRUCTIONS
• The Backrest section is not designed to support the entire weight of the patient. Do
not sit on the Backrest section.
• The table is designed to be a stand alone table. This table must not be modified or
incorporated into any other equipment.
• There are potential pinch points around and underneath the tabletop. It is the
responsibility of the operator of this equipment to insure that bystanders are not in
the area below or around this equipment during operation.
• Proper operation of this equipment is very important for the safety of the operator,
patient, and any other individuals in the area of this equipment. Directions for use
of this equipment are described in this manual. The operator should read these sec-
tions carefully.
• Do not use outdoors.
• Use this furnishing only for its intended use as described in this manual. Do not use
attachments not recommended by Oakworks.
• Weight Limit: (patient and accessories) 500 lbs. (227 kg.) Do not exceed.
PRODUCT USE DESCRIPTION
The Oakworks Powerline & Seychelle Tables are used to support the patient during exami-
nations and procedures. They are intended to be operated by a professional in an exam/
treatment environment. No special training is required but a review of the following manual
is important for the safety of the operator and patient. The professional should read and
understand this entire manual before use with a patient. There are no known contraindica-
tions to the use of this equipment.
IMPORTANT SAFETY INSTRUCTIONS
SYMBOL IDENTIFICATION
This symbol, when used in this manual and on product labels, represents a caution
warning. Be sure to read and comply with all precautions and warnings.

Powerline Flat Top
2
PRODUCT DESCRIPTION
STANDARD SPECIFICATIONS
Height Fixed 30” (76 cm.)
Table Capacity 500 lbs. (226 kg.) (patient and accessories)
Widths 24” (61 cm.), 27” (69 cm.), or 30” (76 cm.)
Length 72” (183 cm.)
Padding 2.5” (6 cm.) Semi-Firm
Paper Roll Holder Accommodates up to 21” (53 cm.) rolls
(roll not included)
Table Weight*90 lbs. (41 kg.)
OPTIONS & ACCESSORIES
QuickLock Face Rest
Table Extender
Inset Shelf (adds 23 lbs. (10.5 kg.))
Padding - 1.75” (4 cm.) Firm Response

Powerline Wave Backrest
3
PRODUCT DESCRIPTION
STANDARD SPECIFICATIONS
Height Fixed 30” (76 cm.)
Wave Backrest Manual 0-60º, 6 set positions
Table Capacity 500 lbs. (226 kg.) (patient and accessories)
Widths 24” (61 cm.), 27” (69 cm.), or 30” (76 cm.)
Length 72” (183 cm.)
Padding 2.5” (6 cm.) Semi-Firm
Paper Roll Holder Accommodates up to 21” (53 cm.) rolls
(roll not included)
Table Weight*90 lbs. (41 kg.)
OPTIONS & ACCESSORIES
QuickLock Face Rest
Table Extender
Inset Shelf (adds 23 lbs. (10.5 kg.))
Padding - 1.75” (4 cm.) Firm Response

Seychelle Flat Top
4
PRODUCT DESCRIPTION
STANDARD SPECIFICATIONS
Height Fixed 30” (76 cm.)
Table Capacity 500 lbs. (226 kg.) (patient and accessories)
Widths 24” (61 cm.), 27” (69 cm.), or 30” (76 cm.)
Length 72” (183 cm.)
Padding 3” (8 cm.) Comfort
Table Weight*90 lbs. (41 kg.)
OPTIONS & ACCESSORIES
QuickLock Face Rest
Table Extender
Inset Shelf (adds 23 lbs. (10.5 kg.))
Padding - 4” (10 cm.) Comfort

Seychelle Wave Backrest
5
PRODUCT DESCRIPTION
STANDARD SPECIFICATIONS
Height Fixed 30” (76 cm.)
Wave Backrest Manual 0-60º, 6 set positions
Table Capacity 500 lbs. (226 kg.) (patient and accessories)
Widths 24” (61 cm.), 27” (69 cm.), or 30” (76 cm.)
Length 72” (183 cm.)
Padding 3” (8 cm.) Comfort
Table Weight*90 lbs. (41 kg.)
OPTIONS & ACCESSORIES
QuickLock Face Rest
Table Extender
Inset Shelf (adds 23 lbs. (10.5 kg.))
Padding - 4” (10 cm.) Comfort

6
TOOLS REQUIRED:
9/16” / 14mm Wrench/Socket
The tables are shipped complete in one box. Follow the step
below to fully assemble the table:
1. Remove the table from the box and place it down on the floor with the
top down. Remove all hardware and the Leg Brace.
2. Unfold the legs to a vertical position and remove any protective wrappings.
3. Install the long large bolts, reinforcement plates, spring washers and lock
nuts as shown, two bolts on each leg. Using the large Allen wrench and
9/16” / 14mm wrench socket, tighten all 8 bolt/nut connections to 12 ft-lbs
minimum or until the spring washers are flat.
4. Install the barrel nut into the leg brace being sure the screw slit is horizon-
tal. Install the short bolt through the leg rail. Start the bolt into the barrel nut
using your fingers first. After the bolt has started, tighten the bolt using the
small Allen wrench. Make sure the leg brace is flush with the adjoining
rails while tightening bolts. Repeat on opposite end of the leg brace.
5. Turn your table right side up. Get up on the table and rock back and forth
to check that all bolts are tight. The table should be very stiff. Dependent
on the environmental conditions of your table, it may be necessary to
periodically re-tighten the hardware.
INSTALLATION
TABLE ASSEMBLY
SHELF ATTACHMENT
If you have ordered a shelf, drop the shelf into place. The shelf has grooves at both ends that enable
it to be held firmly in place by the legs. If necessary, the shelf can be further stabilized by installing the
enclosed Velcro™ strips. Place strips on each corner of the shelf’s bottom side, and on each end of the
rails. Make sure not to mismatch Velcro™ strips; place all “hook” or all “loop” pieces on either the rail or
shelf. The shelf is reversible and can be used on either side.
LEG HARDWARE
8 -Reinforcement Plates
16 - Spring Washers
4 - Long Large Bolts
4 - Lock Nuts
SUPPLIED PARTS:
LEG BRACE
1 - Wood Leg Brace
2 - Short Bolts
2 - Barrel Nuts
TOOLS
1 - Large Allen Wrench
1 - Small Allen Wrench
Barrel Nut
Short Bolt
Leg Brace

7
DIRECTIONS FOR USE
PAPER ROLL HOLDER USE
After the table is set-up,
locate the hole in the leg
at the head end.
Using the supplied
screw & Allen wrench,
secure the paper roll
holder bracket into
place. Repeat step for
the opposite side.
Locate the wooden
dowel & feed it through
your paper roll. Place
the wooden dowel in
the groove located in
each of the paper roll
holder brackets.
To secure the wood-
en dowel, feed it into
the pocket of the
groove on both sides
of the table.
WAVE BACKREST USE
TO RAISE THE BACKREST
Lift the backrest to the desired height and
release. The Backrest support arm will lock in
the nearest slot in the side rail.
TO LOWER THE BACKREST
Lift the backrest slightly, lift and hold the sup-
port arm out of the slot and lower the backrest
to the desired position.
TABLE EXTENDER
CAUTION Do not put excessive weight or pressure on the table extender.
The Table Extender lengthens
the table for your tallest patients
and can improve access to your
patient.
Unfold the dowels and
insert into the outlets.
Locate the Accessory
attachment outlets.
CAUTION Do not adjust the Backrest with a patient on the table.

8
DIRECTIONS FOR USE
Double articulating action provides nearly limitless positioning options with the QuickLock Face Rest.
The adjustable pad takes pressure off sensitive facial areas while providing superb support. The
QuickLock Face Rest can be used in both prone and supine positioning and folds out of the way when
not in use. Adjustments are made easily by loosening the cam locks, adjusting for height and angle
and then locking the cam locks into the desired position.
Important Safety Note:
Maximum Distance from edge of
Table Top= 3” (7.6 cm.)
QuickLock
Face Rest
Insert dowels into
Accessory attachment
outlets.
Loosen Cam Locks &
adjust face rest into place.
The Face Rest can be
used for either prone
or supine positioning.
Tighten the Cam Locks.
QUICKLOCK FACE REST
CAUTION • Do not put excessive weight or pressure on the Quicklock Face Rest.
• Do not extend the dowels of the Quicklock Face Rest 3” (7.6 cm.) from the table top.
• The Maximum Weight Capacity for the QuickLock Face Rest is 25 lbs. (11 kg.)

9
CLEANING & DISINFECTION
RECOMMENDED CLEANERS/DISINFECTANTS
Reference the Recommended Cleaners and Disinfectant list (MMINML0008-EN) that came with the
table. This information can also be found at www.oakworksmed.com under product information.
All cleaners and disinfectants have the ability to degrade the upholstery to some extent. However, fol-
lowing the recommended cleaner and disinfectant list and cleaning process will provided the best care
for your table and support a long product life.
OAKWORKS® recommends a prepackaged wipe for cleaners/disinfectants to ensure best distribution
of disinfectant for the required kill time, without leaving excess residue and/or overexposing compo-
nents therefore minimizing the potential for damage to materials. Please read and follow disinfectants
manufacturers’ directions for cleaning and disinfection.
OAKWORKS® does NOT recommend the use of cleaners/disinfectants containing Hydrogen Peroxide,
Acetic Acid, or Phenolics. These chemicals can cause damage to the appearance and/or material
integrity of various components. Also, while the recommended cleaners/disinfectants list includes
products containing Quaternary Ammonium compounds (“quats”), not all products containing quats
are approved for use. Some contain additional detergents and/or surfactants which can damage some
materials.
A note on Bleach: While a 10% sodium hypochlorite (household bleach) solution (EPA No.: 5813-100
or equivalent) can be an effective disinfectant and is dilute enough to be benign to most materials, it
alone is not an effective cleaner and a separate product must be used for the initial cleaning steps of
the procedure. Because of possible chemical incompatibilities between various cleaning products and
bleach, utmost care must be taken by the user to avoid potential exposure to harmful or toxic by-prod-
ucts of the combination. Also, because bleach leaves a potentially corrosive residue as it evaporates,
it must be rinsed with clean water after disinfection.
Use of non-approved cleaners or disinfectants may lead to damage to upholstery and other
materials found on the table and will void the warranty.
CLEANING PROCESS
Follow the cleaners/disinfectant manufacturers’ directions for use. Please note that cleaning and disin-
fecting an OAKWORKS®table is a two part process. First it must be cleaned of any visible soil, then it
can be disinfected. OAKWORKS® recommends that the table be positioned in the flat position during
the cleaning process. Please follow this procedure for best results:
1. Using an approved cleaner or mild liquid soap and water, clean any visible soil off of the table,
working from the top to the bottom of the table. It is recommended that the upholstery be
cleaned at least once a week to prevent disinfectant build up.
2. Rinse with clean water and dry with a clean cloth or towel.
3. Using an approved disinfectant, thoroughly disinfectant all surfaces of the tabletop and any high-
contact areas such as handles, handsets, etc., making sure they remain wet for the disinfectant
manufacturer’s recommended contact time. Do not allow disinfectant to pool on the upholstery
after the recommended contact time.
4. Wipe off any excess liquid with a cloth or towel and clean water.
5. Dry all surfaces with a clean cloth or towel.
Avoid using writing instruments or other similar instruments around the upholstery as it can cause per-
manent staining. If this does occur, do not wipe with an alcohol based cleaner. Instead, blot the stain
with a clean cloth/ paper towel. Use a 10% bleach dilution to remove the stain. Follow this with a rinse
of clean water.

10
INSPECTIONS / WARRANTY
INSPECTIONS
RECOMMENDED REGULAR INSPECTIONS (monthly or local standard)
• Visually inspect components for obvious damage that could cause problems during operation.
RECOMMENDED PERIODIC INSPECTIONS (yearly or local standard)
• Visually inspect components for obvious damage that could cause problems during operation.
• Check that all fasteners are present and fastened securely.
• Clean unusual buildup of dirt on the table and/or parts of the table not normally cleaned on a regular
basis.
• Check for tears or cracks in the upholstery.
WARRANTY
View complete warranty details at www.oakworksmed.com under the information tab
“Warranty and Return Policy”

11
MODEL NUMBER & SERIAL NUMBER
MODEL & SERIAL NUMBERS
Model Number
Serial Number
Model Numbers and Serial Numbers always start
with a letter.
The model number
and serial number are
located under the top
of the table.
16796025 PWMPFT303072CFTTZZNTXXXX
Ser#: PWK1565022
PWK Powerline Flat Top 30 x 30 x 72 CF/TT/NT/XX
TTSKYBLUE 01/04/2020 Order#:654321
Notes: Sample Product Label

12
SPECIFICATIONS
PRODUCT SPECIFICATIONS
Weight 90-113 lbs. (41-51) kg.
Weight Limit 500 lbs. (226 kg.)
ENVIRONMENTAL CONDITIONS
Conditions Temperature Humidity Atmospheric Pressure
Normal Use 50° (10°C) to 104° (40°C) 20% to 60% RH 98 to 105 kPa
Storage & Transport -20° (-29°C) to 135° (57°C) 20% to 95% RH 98 to 105 kPa

Manual Part Number MMMNST0005-EN / Med-RA-PM-44
Revision level: 7
Revision Date: 05/19/2021
English, Printed in USA
CONTACT INFORMATION:
Oakworks®Inc.
923 East Wellspring Road
New Freedom, PA 17349
Phone: [phone]
FAX: [phone]
www.oakworks.com
OAKWORKS®
Treatment Tables
USER MANUAL