Oasis Aquatics SF24-40 User manual

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
1
INSTALLATION AND OPERATION MANUAL
SF MEDIA FILTER
Head Office
62 Parkhurst Drive
Knoxfield VIC 3180
T: 03 9887 2131
New South Wales
Unit 1, 20-22 Foundry Road
Seven Hills NSW 2147
T: 02 9838 0000
Queensland
Unit 4, 8 Reichert Drive
Molendinar QLD 4214
T: 07 5679 6821
[e-mail]
oasisaquatics.com.au

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
2
PLEASE READ
THESE
INSTRUCTIONS
BEFORE
OPERATING.
Please pass these instructions on to the
owner of this equipment.
SF24-40SF24-50 SF28-50 SF31-50

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
3
CONGRATULATIONS ON
PURCHASING YOUR OASIS
SF MEDIA FILTER.
THIS MANUAL HAS BEEN CAREFULLY DEVELOPED TO GIVE
YOU ALL THE INFORMATION YOU NEED TO GET THE BEST
VALUE FROM YOUR PURCHASE.
It is important that you read through the manual to identify the key areas you need to
understand, particularly the following:
•Health and Safety Concerns
•Installation requirements
•How to operate the major features of the unit
•The importance of maintenance
•If you have a problem, what to trouble shoot before you contact your professional
•Finally, your entitlements under your product warranty.
Oasis have developed their product to provide you with the ultimate experience and are sure
you will be delighted with your purchase.
Please note: This manual has been designed to cater for installation rules
and codes in the USA, Canada and Australia. Specific rules and regulations
for each country has been highlighted by the National flag of each country.
Please ensure you follow the installation rules specific to your country.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
4
WE CARE ABOUT YOUR SAFETY
IMPORTANT WARNINGS
Warning –read and follow all instructions in this owners manual
and on the equipment. Failure to follow instructions can cause
severe injury and/or death.
Oasis highly recommend the installation of all their equipment by a suitably qualified pool
professional who will ensure your high performance Oasis products are installed to your local
standards and codes to ensure optimum safety and performance.
CAUTION
All components of the filtration system including Pumps, Filters, Heaters must be positioned
so to prevent being used as means of access to the pool by young children. To reduce risk of
injury, do not permit children to use or climb on this product. Closely supervise children at all
times.
WARNING- HAZARDOUS PRESSURE.
Hazardous Pressure. Pool and Spa water circulation systems operate under hazardous pressure
during start up, normal operation, and after pump shut off. Stand clear of circulation system
equipment during pump start-up. Failure to follow safety and operation instructions could
result in violent separation of the pump housing and cover, and/or filter housing and clamp due
to pressure in the system, which could cause property damage, severe personal injury, or
death. Before servicing pool and spa water circulation systems, all system and pump controls
must be in the off position and filter manual relief valve must be in open position. Before
starting system pump, all system valves must be set in a position that allows system water to
return back to the pool. Do not change filter control valve position whilst system pump is
operating. Before starting system pump, fully open filter manual air relief valve. Do not close
filter manual air relief valve until a steady stream of water (not air) is discharged.
Cleaning the Sand Filter by BACKWASHING and RINSING is essential to providing clean, safe and
healthy swimming water. A regular cleaning program is highly recommended especially in
Commercial applications, the time between cleans and length of cleaning time will depend on
size of pool, bather load and other environmental conditions. Discuss with your local pool
professional to work out a program that best suits your pool.
WARNING- RISK OF ELECTRICAL SHOCK OR ELECTROCUTION

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
5
WE WANT YOU TO BE DELIGHTED WITH
YOUR PURCHASE, CORRECT
INSTALLATION WILL PROLONG LIFE
AND MAXIMISE THE PERFORMANCE OF
THIS UNIT.
Your filter is high performance and corrosion proof designed with superior flow characteristics
that is easy to operate. Everything is made simple from installation, operation, to the
maintenance of the filter. Your Oasis filter will provide crystal clear, healthy swimming water
with minimal maintenance.
Oasis highly recommend the use of qualified service technicians to ensure the best
performance as well as the health and safety of your family.
HOW IT WORKS
Your Oasis Media filter is designed to use the high-quality filter elements to remove dirt
particles from pool water. These elements are specifically designed for your Oasis Media filter
and if looked after will provide you with years of trouble-free operation. The pool water which
contains dirt particles is pumped through your system to the filter. As pool water passes
through the filter, dirt particles will be caught by the filter element and removed from the
water. The cleaned pool water is returned back to the pool through your piping system. The
entire process is continuous and automatic. It is this process that provides the filtration and
removal of organic material such as dust, dirt and fine particles in your pool water.
During this process, dirt will accumulate in the filter element and gradually increase the
pressure in the tank and reduce the flow of water through your filtration system. This means it
is time to clean your filter element. A good indication when to clean the filter element is by
checking the pressure gauge reading. Cleaning should be performed when you notice the
pressure has increased by 5 PSI or 35 kPa from when it was clean. Following the cleaning
procedure for the best results.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
6
SPECIFICATIONS AND DIMENSIONS
Model #
SF24-40
SF24-50
SF28-50
SF31-50
Filtration Area (m2)
0.28
0.28
0.36
0.47
Max Flow Rate (litres pm)
250
320
350
400
Turnover Capacity –8 Hours
(Litres)
120,000
153,600
168,000
192,000
Turnover Capacity –8 Hours
(Gallons)
31,680
40,320
44,160
50,400
Sand Required (kg)
125
125
185
320
A (mm)
980
1,032
1,133
1,178
B (mm)
860
873
976
1,021
C (mm)
800
807
910
955
D (mm)
280
280
300
370
E (mm)
600
600
675
775
B
D
C
E
A

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
7
INSTALLATION
The Filter should be installed as close to the pool as possible but keep a distance of at least
1.5m. Locate the Filter on rigid, level surface, preferably in a dry, shaded, and well-ventilated
area. Prior to installation take into consideration the following conditions:
•Position of suction and return PVC connections
•Access for backwashing operation and servicing
•Protection from sun, rain, splashing etc
•Drainage of filter room
•Ventilation and protection of the full filtration system
Once you are happy that the above has been considered, follow
these steps:
1. Place the empty tank in position
2. Fill the tank with water to the level that covers the laterals, or about 1/3 of the tank
height. This will avoid damage to the laterals by the force of the sand when pouring into
the filter
3. Pour the recommended amount of sand into the tank, ensuring that the centre-pipe
remains centred and vertical
4. Level the surface of the sand upon completion
5. Remove the Sand Fill Cover
6. Carefully remove all sand particles from the valve mounting surface
7. Place the O-ring into the groove on the tank
8. Lower the Multiport Control Valve carefully into position so that its underside engages
with the centre-pipe. Rotate the valve until the inlet is approximately in line with the
pump.
9. Place the clamp set around the tank and the valve. Secure using the screw provided.
10. Firmly tap with a rubber mallet outside of the clamps as you tighten the screw, refer to
Figure below
11. Tighten the screw until the Multiport Control Valve is properly assembled to create a
water tight seal. Do not over tighten.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
8
WARNING
Is it important when connecting the WASTE line that you adhere to any local standards and
codes in relation to the disposal of the waste water. It is also highly recommended to use
minimum 40mm (1.5”) PVC Pipe with the SF24-40 Filter and minimum 50mm (2.0”) PVC Pipe
with all other SF Filters. To reduce any pressure to provide the best clean possible reduce the
distance and amount of bends used for the WASTE discharge line.
To prevent water leakage, be sure all pipe connections are tight
Prior to starting the filtration process by turning on the pump, we highly recommend that
you read through the pump instruction manual to ensure proper installation and to avoid
the risk of electric shock.
CONGRATULATIONS, YOU HAVE NOW
INSTALLED YOUR NEW OASIS AQUATICS
FILTER.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
9
START-UP PROCEDURE
1. Be sure the correct amount of filter sand media is in the tank and all connections have
been made and are secure.
2. Turn the Multiport Control Valve handle to the “Backwash” position. Press the handle
downward before turning.
3. Start the pump according to pump instruction manual (be sure all suction and return
lines are open).
4. Once water flow is steady out the waste line, run the pump for at least 2 minutes. The
initial backwashing of the filter is recommended to remove any impurities or fine sand
particles in the sand media.
5. Turn the pump off and set the control valve to RINSE position. Start pump and operate
until water in sightglass is clear. Turn pump off, set valve to FILTER position and restart
pump. Your filter is now operating in the normal filter mode, filtering particles and dirt
from the pool water.
6. Take note of the initial pressure gauge reading for future reference. Variation may occur
from pool to pool.
7. Adjust pool suction and return valves to achieve desired flow. Check system and filter for
water leaks and tighten connections, bolts, nuts as required.
NOTE: During the initial clean-up of the pool water, it may be necessary to backwash frequently
due to the unusually heavy initial dirt load in the water.
IMPORTANT: To prevent unnecessary strain on piping system and control valve, always turn off
the pump before changing the operation of the control valve. To prevent damage to the pump
and filter and for proper operation of the system, clean pump strainer (basket) and skimmer
basket(s) regularly.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
10
MULTIPORT CONTROL VALVE
FUNCTIONS
The Multiport Control Valve controls the direction of water flow throughout your filter allowing
you to easily filter your swimming pool water and then clean your filter tank. Correct operation
of the Multiport Control Valve will give you healthy, clean water for many years. It is important
to understand the functions of each setting which is explained below.
Please take a moment to read and understand.
1) FILTER
This is the standard position when your filtration system is in normal operation. The water
flows in from your pool and is distributed across the top of the sand bed in the filter. Through
pressure this water is pushed down through the Sand allowing debris to be removed from the
water and collected in the sand bed. Water is then taken up through the laterals and the centre
stem pipe and returned to the pool, usually via some form of sanitation and/or heating. The
filter position can also be used for manual vacuuming and cleaning.
2) BACKWASH
This position is used when the sand bed requires cleaning. Use the Pressure Gauge to indicate
when this is required, usually 5 PSI or 35 kPa above operation of a clean filter. When backwash
is selected the water flow is reversed and goes down the stem pipe and out through the
laterals. This lifts the sand bed and allows debris to be taken up the filter and out through the
waste pipe. The sight glass will show the quality of the water and you need to backwash until
this water is clear.
3) WASTE
The waste position allows you to pump excess water from the pool directly down the waste
pipe. This position is useful after heavy rains where the water level is too high. Water is
directed straight through the Multiport Control Valve and bypasses the filter, going directly to
waste. You can also use this position to vacuum heavy concentration of debris from the pool.
4) RECIRCULATE
Similar to the Waste setting, Recirculate allows the water to bypass the filter but goes straight
back to the pool. This is a useful setting if you have applied some chemicals that need to be
circulated, but not removed by the filter. In addition, if a leak develops in the filter use
recirculate to continue circulating water until it is fixed.
5) RINSE
Rinse is a very important setting to use after you have completed the Backwash cycle. In the
Rinse setting, water is taken from the pool and distributed on the sand bed. This downward
flow settles the sand bed after backwashing and carries any remaining loose dirt through to the
waste line. By using Rinse after Backwashing you will eliminate any debris returning to the pool
water. Rinse until you see clear water in the Sightglass and should take half the time of a
Backwash cycle.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
11
6) CLOSED
Closed setting acts like a Valve and prevents flow of water through the Tank, particularly useful
if doing any maintenance on the filtration system.
BACKWASHING YOUR FILTER
Cleaning your Filter will give you the best quality swimming water that is clean, clear and safe
for swimming. It is highly recommended to clean on a regular basis and to monitor the pressure
gauge and BACKWASH when an increase of 5 PSI or 35 kPa is indicated from your clean filter.
TO PERFORM THE BACKWASH OPERATION, YOU MUST FOLLOWING THESE
STEPS:
1. Turn off Pump
2. Change the position of the Multiport Control Valve handle from FILTER to BACKWASH
3. Turn Pump back on. The water flow is automatically reversed through the Filter so the
water is directed from the bottom of the tank, up through the sand, flushing the trapped
dirt and debris out of the waste line.
4. Check Sight Glass. The duration of the backwash operation will depend on how dirty your
filter is. Continuously check the sight glass to see when the water becomes clear, then
5. Turn off Pump
6. Change the position of the Multiport Control Valve handle from BACKWASH to RINSE
7. Turn Pump back on. The water flow will now be directed back through the Sand bed and
then out through the waste line. This will settle the sand bed back for normal operation.
8. Check Sight Glass. Continue until water in Sight Glass is clear, usually about half the
time of the backwash cycle.
9. Turn off Pump
10. Change the position of the Multiport Control Valve handle from RINSE to FILTER.
11. Turn on Pump
WARNING
Turn off the pump before switching the control
valve handle.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
12
WARNING
Cleaning the Sand Filter by BACKWASHING and RINSING is essential to providing clean,
safe and healthy swimming water. A regular cleaning program is highly recommended
especially in Commercial applications, the time between cleans and length of cleaning
time will depend on size
of pool, bather load and other environmental conditions. Discuss with your local pool
professional to work out a program that best suits your pool.
WHEN VACUUMING THE POOL
If using your Manual Vacuum System to clean the pool. The following can be used as a guide for
settings on your Multiport Control Valve.
•Light Soil, general clean - set the control valve to FILTER position
•Heavy Soil, specific clean - set the control valve to WASTE position. If using the WASTE
position, ensure that the pool water level is well above your skimmer box level as the
water will be directed down the waste line.
WINTERISING
Winterising is preparing your pool for freezing conditions which can potentially damage all pool
filtration equipment due to water expanding when frozen. We highly recommend the following
steps when preparing your filter for winter conditions:
1. Backwash the filter for at least thirty minutes before closing down the pool for
winterising. This will clean the filter bed thoroughly and remove any debris from the
system.
2. Drain the filter tank by removing the drain cap at the base of the filter tank. Leave the
cap off during winter.
3. Set the control valve handle between the RINSE and FILTER. This will lift the handle and
help with the draining process by allowing air to enter into the tank.
4. Unscrew the pressure gauge from the control valve and store the gauge indoors.
5. Drain and winterise pump according to pump instructions.
This is an ideal time for any repairs that may be required during the off-season. Most pool
professionals will recommend want is needed before the next pool season.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
13
TROUBLESHOOTING
The chart below identifies some of the main issues you may encountered with your sand filter.
This should assist with the majority of problems. OASIS highly recommends regular checks and
maintenance of your swimming pool equipment by a qualified pool professional.
This will extend the life of your equipment and give you the best performance.
WHAT IS THE PROBLEM?
WHAT YOU CAN DO ABOUT IT?
Sand Entering the Pool
•Sand too small and getting through Laterals
•Flow rate on Pump is too high and pushing sand
through Laterals
•Sand Bed Calcified due to poor water chemistry
•Broken Lateral
•Loose Centre-Pipe
•Too much Sand in Tank
•Multiport Control Valve not correctly in Filter position
•Too much Air in Filter
Sand coming out of Waste Line
•Flow rate on Pump is too high and lifting Sand too high
on Backwash
Pool Water is Cloudy due to poor
Filtering
•Sand Bed is dirty and requires Backwashing
•Incorrect Sand has been installed
•Sand Bed is too low
•Algae build-up in Filter due to poor water chemistry
•Excessive dirt in pool
•Calcified Sand Bed due to poor water chemistry
•Heavy Swimmer Load
•Flow rate on Pump is incorrect for Filter size and Pool
size
•Backwashing Cycle is too Short
•Backwash line is too small restricting water flow
Filter Leaking Water
•Tank Cracked
•Drain Plug not tight
•Valve to Tank O-ring damaged
Multiport Control Valve Leaks
•Handle is not properly located in selected setting
•Valve to Tank O-ring damaged
•Valve Cover O-ring damaged
•Pressure Gauge O-ring damaged

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
14
Abnormal Loss of Pool Water
•Leak inside Control Valve
•Leak from Pool or PVC Piping
High Pressure Filter
•Filter requires Backwashing
•Calcified Sand Bed due to poor water chemistry
•Return lines too small for flow rate of Pump
Low Pressure in Filter
•Multiport Control Valve incorrectly set
•Pump Flow Rate is too slow, check speed and other
control valves
•Air leak in Pump Suction
NOTE: If the recommendation in this manual does not solve your particular
problem(s), please contact your local dealer for service.
POOL CHEMISTRY GUIDELINES
To get the best performance out of any of your pool equipment, it is important that you manage
your water chemistry to the ideal swimming levels. This could vary according to your location
and OASIS highly recommend that you employ the services of your local pool professional to
get your pool set-up to exactly what is required.
The below chart gives some guidelines to the major water chemistry areas to provide the best
performance and to maximise your equipment life. Should your chemistry fall outside the
suggested ranges, this could be damaging to the equipment and its performance.
IMPORTANT POOL
CHEMISTRY LEVELS
RANGE
pH
7.2 to 7.6
Total Alkalinity
100 to 130 ppm
Total Chlorine
1.0 to 3.0 ppm
Stabiliser (Cyanuric Acid)
40 to 70 ppm
Salt / Mineral
Max 5,000 ppm

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
15
PRO-ACTIVE MAINTENANCE PROGRAM
Like your motor vehicle it is important to maintain a regular service program for your pool
equipment to ensure the best operation and long lasting results.
The below chart provides a guideline to follow to best look after your valuable equipment.
Regular maintenance can identify any potential issues early and save on expensive maintenance
at a later date
WHEN?
WHAT ARE YOU LOOKING
FOR?
HOW CAN YOU FIX?
Weekly
Check Pressure Gauge
If pressure increases by5 PSI / 35
KPA, then BACKWASH and RINSE
the filter as per instructions.
Quarterly
Check all Gaskets & Pressure
Gauge
Isolate and turn off the Pump.
Remove all Gaskets and turn over.
You can also apply a silicon based
grease to extend the life. If dry,
then contact your local pool
professional to replace.
Check around the unit for
leaves/debris or signs of
flooding.
Replace any debris that is
restricting air circulation around
the Filter. If in a flood prone
location, rectify
Check for any Insects/Ants
etc
It is a good practice to use a good
quality surface spray around your
equipment. Make sure all units are
turned off and then spray around
all units to eliminate any
insect/ants etc
Check for any leaks
If you notice any water leaking
from the filter or other equipment.
Check gaskets first and reseal. If
continues, contact your local pool
professional to assess and rectify.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
16
REPLACEMENT PARTS OF FILTER
Key No
Part No
Description
1
88281550B
6 Way 1.5”Valve with 1.5”union set x3 pressure gauge
1
88281551B
6 Way 2”Valve with 2”union set x3 pressure gauge
2
06021013
Plastic Pressure Gauge with O Ring
2
01111048
Connector for Pressure Gauge / Stopper
3
89280102B
1.5” Union Set (Black) with O Ring
3
89280102W
1.5” Union Set (White) with O Ring
3
89280103B
2” Union Set (Black) with O Ring
3
89280103W
2” Union Set (White) with O Ring
4
03021035
M6 Nut
5
89012512
Clamp Kit
6
01111101
Star-Shaped Nut
7
03011166
M6 x 110 mm Screws
8
02010007
O Ring
9
89012501
Filter Tank for MF17
9
89012502
Filter Tank for MF20
9
89012503
Filter Tank for MF24
9
89012504
Filter Tank for MF27 / Filter Tank for MF27 A
9
89012505
Filter Tank for MF35 / Filter Tank for MF35 A
9
89012506
Filter Tank for MF35
10
89012507
Lateral Assembly with Centre Pipe for MFV17
10
89012508
Lateral Assembly with Centre Pipe for MF20
10
89012509
Lateral Assembly with Centre Pipe for MF24
10
89012510
Lateral Assembly with Centre Pipe for MF27A
10
89012513
Lateral Assembly with Centre Pipe for MF27
10
89012511
Lateral Assembly with Centre Pipe for MF31A
10
89012514
Lateral Assembly with Centre Pipe for MF31
10
89012515
Lateral Assembly with Centre Pipe for MF35
11*
01172007
Laterals (115mm)
11*
01172008
Laterals (126mm)
11*
011720010
Laterals (186mm)
12
89011601
Water Drain Ser
13
01111059
16-21 Inch Filter Base
13
01111062
21 –21 Inch Filter Base
13
01112037
31 –35 Inch Filter Base
Notes:
11* MFV17 Should have 8 pcs of
Lateral (115mm)
11* MFV20/ MFV24/ MFV27 A
Should have 8 pcs of Lateral
(126mm)
11* MFV27/ MFV31/ MFV35 Should
have 4 pcs of Lateral (115mm) and 4
pcs of Lateral (185mm)

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
17
WARRANTY
Oasis Aquatics warrants that, subject to the exclusions and limitations that follow, the product
will be free from defects in materials and workmanship during the warranty period of five (5)
years. The warranty period for your Filter is set our below and commences from the date of
purchase which must be proved by the retailer invoice.
This warranty is not assignable and applies to the original retail purchaser only and the original
receipt, invoice or any other proof of purchase must be retained and produced if requested by
the Company.
Nothing in this warranty shall apply to any defects caused by misuse or abuse, neglect,
accident, extremes of climate, dampness, humidity, reasonable fair wear and tear and/or any
causes other than detects in manufacturing and materials. Proper care and maintenance
information is detailed in the Owner’s Manual for this product which you must follow.
Where a defect is physically visible or otherwise affects the exterior surfaces of the product,
you must notify the Company of such defect within fourteen (14) days from the date of your
purchase.
If a defect in materials or workmanship occurs within the warranty period Oasis Aquatics will,
at its discretion repair or replace product or the defective part of the product free of charge or
cause the product or the defective part to be repaired or replaced by an Authorised Oasis
Aquatics Service Agent free of charge.
Oasis Aquatics reserves the right to substitute defective parts or the Product with parts or
product of similar quality, grade and performance where an identical part or product is not
available. Parts or products may be replaced by refurbished goods of the same type rather than
be repaired.
If the product is bought as a demonstration, refurbished, ex-rental, discontinued or otherwise
previously unboxed unit, the warranty applicable shall be limited to twelve (12) months only.
Warranty Procedure
If a fault that is deemed to be covered by warranty occurs, the customer must first contact
their retailer and/or builder from which the product was purchased and/or installed.
Any claim must be justified with the following details:
•Proof of Purchase date along with relevant invoice details,
•Full details of the fault, and
•Customer Name, Address and Contact details
The retailer and/or builder will assess the problem and assist Oasis Aquatics with the
warranty procedure.
The product must be made available to Oasis Aquatics or its authorized service agents for
full inspection, diagnosis, testing and repair.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
18
If advised to return the product, place the defective product in secure packaging, clearly
label it and send it to the address of the authorised service agent which will be advised by
your dealership.
If the installation of the product is outside a radius of 30 km (20 miles) from an
Authorised Oasis Aquatics Service Agent, a service technician travelling fee will apply.
If no defect in materials or workmanship is found, a fee must be paid for Oasis Aquatics’s
costs of service, diagnosis and testing. If such a circumstance you request that Oasis
Aquatics or Authorised Service Agent complete the non-warrantable repair, a fee will apply
for labour and parts used to repair the product.
EXCLUSIONS
The warranty will not apply where
•The customer has not complied with Oasis Aquatics terms and conditions of sale
•The product was used in an application for which is wasn’t intended
•The product was altered, modified or repaired by any other person than Oasis Aquatics or
its Authorised Service Agents
•The Product has not been installed, maintained or operated in accordance with
Installation and Operating Instructions
•The product has been subject to misuse, abuse, negligence, alteration or accident
•Environmental influences such as flooding, storm, lighting, fire
•Running filtration system without water
CUSTOMER RECORD (To be retained by the customer)
DEALER / INSTALLER NAME
SERIAL NUMBER
DATE INSTALLED

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
19
Commercial Installations.
Commercial Installation are defined as installations where the pool user pays for the use of the
pool either directly or indirectly through hiring or renting of accommodation or membership of a
gym, health centre or public pool AND where the pool equipment is operating for more than 16
hours per day.
In such installations the warranty period is limited to 1 year.
Consequential Damages
Oasis Aquatics shall have no liability for incidental or consequential damages or delays caused
either directly or indirectly by any malfunction, defect or failure of the equipment.
No person is authorized to make any representation or warranty on behalf of Oasis Aquatics
without express written consent from Oasis Aquatics.

SF MEDIA FILTER INSTALLATION AND OPERATION MANUAL
[e-mail]
oasisaquatics.com.au
20
A part of the
group
Victoria
62 Parkhurst Drive
Knoxfield VIC 3180
Australia
T: 03 9887 2131
New South Wales
Unit 1, 20-22 Foundry Road
Seven Hills NSW 2147
Australia
T: 02 9838 0000
Queensland
Unit 4, 8 Reichert Drive
Molendinar QLD 4214
Australia
T: 07 5679 6821
oasisaquatics.com.au
[email protected]m.au