Oceanled OceanBridge User manual

PRODUCT CODE: 013201
OceanBridge
MULTIZONE LIGHTING CONTROLLER
The OceanBridge is a patented multizone lighting controller, designed specifically for
easy control of all your boat’s lights from an MFD, smartphone, or tablet. This innovative
system allows you complete control of the entire OceanLED range of lights and accessories,
as well as most third-party (DMX or on/o) DC-powered lights. The OceanBridge gives
you complete control, of colour change, music sync, colour fade, colour transitions,
brightness, zone creation, and our patented movement-to-colour functionality.
Expandable
System
Touch
interface
10 Dynamic
Scenes
Universal
Compatibility
Colour
Control
10 Lighting
Zones
Dynamic
Audio Mode
Wave Motion
Mode
Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.comOcean LED Marine LTD / Tel [phone] / [e-mail]
Specifications are subject to change without notice.
PRODUCT CODE: 013201
Quick Install Guide
TECHNICAL INFORMATION:
Water Protection
Rating
IP66 Bluetooth Built-In
Power
Consumption
6W (500mA @12V DC)
NMEA2000 Bus Powered LEN = 10
Material Robust Polycarbonate
Operating
Voltage
12/24V DC (Max 32V DC) On-board Sensors Gyroscope/Accelometer Sensor
Thermal Sensor
Power Input NMEA2000 Connector Port Operating
Temperature
-10°C to 50°C ambient
Wi-Fi Built-In Network
Connections
NMEA2000 connection
Ethernet connection
External Switch
Inputs
Supports Four External Switch Inputs Audio 1 x Audio-In 3.5mm
1 x Audio-Out 3.5mm
USB Connectivity 1 x USB port (Memory stick only) DMX / RDM
(RS485 Interface)
1 x DMX512-A Input
1 x DMX512-A Input / Output
Warranty Serial Code:
For the full instructions, scan
the QR code below:
To register your product
and receive notifications
for software upgrades, scan
the QR code below:
FULL INSTALL MANUAL PRODUCT REGISTRATION

Ocean LED Marine LTD / Tel [phone] / [e-mail] Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.com
Specifications are subject to change without notice.
BOX CONTENTS:
UNIVERSAL COMPATIBILITY AND CONTROL
The OceanBridge is compatible with all major MFD units,
including Garmin, Simrad, Lowrance, B&G, Raymarine, and
Furuno.
CONTROL METHODS:
• HTML5 app integrated with the MFD unit
• NMEA2000 lighting PGNs (Navico Group only)
• Web Browser Interface (Phone, Tablet or Laptop/PC)
AUDIO INTEGRATION:
• External Audio Input (Vessel Stereo or iPod/MP3)
• Bluetooth (Phone, Tablet, Laptop/PC)
SUPPORTED LIGHT TYPES:
• Four Channel: RGBW lights
• Three Channel: RGB lights
• Two Channel: Dual-colour lights
• Single Channel: Dimmable lights
• Single Channel: Switchable lights
• 2010/3010 Single Colour (legacy OceanLED lights)
• Power Toggle Single (requires OceanConnect JB)
• Power Toggle Dual (requires OceanConnect JB)
MODE & FUNCTION OPTIONS:
✓Colour Change
✓Colour Fade
✓Colour Transition
✓Brightness
✓Music Sync
✓Zone Creation
✓Movement to Colour Sync
✓Scene Setup
✓Light Eects
IMPORTANT FEATURES
• Wi-Fi: Built-in Wi-Fi allows the unit to be directly
connected to a smartphone or laptop to control lights.
The default Wi-Fi SSID is “OceanBridge” and the
password is “password”. Once connected, use a web
browser to access http://192.168.0.1 . The SSID and
password should be changed in the Wi-Fi settings menu.
The system can be connected to any existing on-board
Wi-Fi network.
• Scene Setup: On the Home Screen, click the ‘Save
Scene’ to save the current setup for each zone. The scene
can then be named and saved. A ‘Scene Card’ will then
be created. Selecting this will recall the saved zone settings.
• Trigger Inputs: Up to four external switches can be
connected to trigger saved scenes or turn zones on/o.
The actions are configured by opening the main menu
and selecting ‘Settings/External Trigger Setup’.
• Timers: Scenes or lights o can be triggered via timers.
In the main menu, select ‘Settings/Timer Setup’ to setup
timers.
• Security Pin: Lock individual feature with a four-digit
password. Access the main menu, then select ‘ System/
Security’, type default PIN: “1234”. Select the feature
you would like to lock using the tick box list. Set your
code, then click ‘Lock/Apply’.

Warning: Product installation and operation
Before installing the OceanBridge, read and follow all
warning notices and instructions which are included.
Failure to follow safety warnings and instructions can
result in property damage, severe injury or even death.
Warning: Power supply voltage
Connecting this product to a voltage supply greater than
the specified maximum rating may cause permanent
damage to the unit. Refer to the Technical Specification
section for voltage rating.
Warning: Hazardous or flammable atmospheres
This product is NOT approved for use in hazardous or
flammable atmospheres. DO NOT install it in areas with
hazardous or flammable atmospheres, such as engine
rooms or near fuel tanks.
Danger: Risk of electric shock or electrocution
This OceanBridge unit must be installed by a licensed or
certified electrician in accordance with all applicable local
codes and ordinances. Improper installation will create
an electrical hazard which could result in death or serious
injury to swimmers, installers, or others due to electrical
shock, and may also cause damage to property.
Warning: Switch o power supply
Ensure the vessel’s power supply is switched OFF before
starting to install this product. Do NOT connect or discon-
nect equipment with the power switched on.
IMPORTANT INFORMATION
CAUTION: Power supply protection
When installing this product and using the OceanLED
power cable, make sure the power source is adequately
protected by using a suitably-rated fuse or automatic
circuit breaker.
Water ingress disclaimer
Although the waterproof rating capacity of this product
meets the IP66, water intrusion and subsequent equip-
ment failure may occur if the product is subjected to,
such as but not limited to, high-pressure washing and/or
submersion/flooding. OceanLED will not warrant products
if the cause of failure is greater than the requirements for
IP66 rating.
EMC installation guidelines
OceanLED equipment and accessories conform to
the appropriate Electromagnetic Compatibility (EMC)
regulations, to minimize electromagnetic interference
between equipment and minimize the eect such
interference could have on the performance of your
system.
FCC Compliance
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and
meets the FCC radio frequency (RF) Exposure Guidelines.
This equipment should be installed and operated keeping
the radiator at least 20cm or more from the person’s
body.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
FCC Caution
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
This device complies with below part 15 of the FCC Rules.
• Part 15 Subpart C
• Part 15 Subpart E
Warning: USB connection
The OceanBridge product is equipped with a USB data
connection specifically intended for the connection of
USB memory storage devices. Please DO NOT attempt to
connect devices with AC power sources, such as PCs or
Laptops, to the OceanBridge product using the USB port.
This port is exclusively designed for USB memory storage
devices only to ensure safe and optimal functionality.
Product disposal
Dispose of this product in accordance with the WEEE
Directive.
Caution: Service and maintenance
This product does not contain user-serviceable
components. Please direct all maintenance and repair
inquiries to authorized OceanLED dealers. Unauthorized
repairs could impact your warranty.
Unit cleaning instructions
The unit does not require regular cleaning. However, if you
find it necessary to clean the unit, please follow the steps
below:
1. Ensure power is switched o.
2. Wipe unit clean with a damp cloth.
3. If necessary, use a mild detergent solution to remove
grease marks.
Technical accuracy
To the best of our knowledge, the information in this
document was correct at the time it was produced.
However, OceanLED cannot accept liability for any
inaccuracies or omissions it may contain. Please
check the OceanLED website (www.oceanled.com) to
ensure you have the most up-to-date version(s) of the
documentation for your product.
SAFETY NOTICES:
Ocean LED Marine LTD / Tel [phone] / [e-mail] Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.com
Specifications are subject to change without notice.

CONNECTIONS OVERVIEW:
Item Function
A DMX Out
B DMX In/Out
C NMEA2000 / Power (12/24V)
D Ethernet
E Audio In
F Audio Out
G Switch Input
H Diagnostic LEDs
I Test/Reset Switch
J USB Port (Memory Stick only)
Diagnostic LEDs (H):
ID LED STATUS
1 Green - ON Unit operating properly
2 Amber - ON Reading Devices (RDM mode)
3 Red - ON Overheating
4 Amber, Green, Red - ON Loading System
5 Green, Red - ON Factory Reset Initialized
Test/Reset Switch (I):
ID SWITCH FUNCTION
1 Press once (short press) Test Mode – The unit will execute power on sequence on all
connected devices
2 Press and hold until Amber LED ON (approx. 5s) Reboot/Reload the OceanBridge App
3 Press and hold until Red LED ON (approx. 30s) Factory Reset – All data and settings will be erased
DIMENSIONS
Ocean LED Marine LTD / Tel [phone] / [e-mail] Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.com
Specifications are subject to change without notice.

MOUNTING
1. Find a suitable mounting location and consider your wiring
route, surfaces and position. For utilizing the movement-to-col-
our function the unit should be mounted in or as close as pos-
sible to the rotational centre of the vessel (See full manual for
details). Please consider location to prevent Wi-Fi and Bluetooth
signal issues.
2. Check to ensure there are no obstructions, such as cables or
pipes behind your mounting area.
3. The unit’s mounting holes are located at the four corners of the
lid.
4. The provided mounting screws are designed to be compatible
with various surfaces, such as wood or fibreglass. Before mount-
ing, mark the desired hole positions and drill pilot holes accord-
ingly. Take caution to verify the absence of any obstructions,
such as cables or pipes behind the drilling area.
5. Mount the OceanBridge unit using the screws provided. Ensure
all four mounting holes are secured. Tighten screws by hand
only.
Ocean LED Marine LTD / Tel [phone] / [e-mail] Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.com
Specifications are subject to change without notice.
CAN BUS (NMEA2000)
Connect an NMEA2000 drop cable (not provided) to the OceanBridge NMEA2000/Power port and the other end of the
cable to the backbone of the NMEA2000 installation.
ELECTRICAL INSTALLATION
Power Connection
Use the OceanBridge Power Cable (p/n: 013202; not included with OceanBridge – p/n: 013201). Connect the end with the
socket to the OceanBridge NMEA2000/Power port and link the other end to the on-board battery. Connect the +VE Red
wire to a +12/24V fused power source. Connect the -VE Black wire to the battery - (Ground) supply.

ELECTRICAL INSTALLATION
CONNECTING LIGHTS:
Example: EXPLORE Series E6 & E7 DMX
For the straightforward connection with the Explore E6 & E7 lights, use Explore E6 & E7 Control Link Cable (not provided,
see full manual Appendix 9.5). Connect the male plug of the cable with the OceanBridge DMX OUT port and connect the
other end to the first light in the DMX chain. Ensure to terminate the last device in the DMX chain with the DMX terminator
(optional).
Ocean LED Marine LTD / Tel [phone] / [e-mail] Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.com
Specifications are subject to change without notice.
Please ensure you have read the full Installation Manual before fitting this product.
MFD Install – Ethernet Connection
Connect the OceanBridge unit to the MFD using the Ethernet cable (not provided). Please refer to the full manual for con-
nections with dierent MFD manufacturers.
Audio
Depending on your audio device, you will need the appropriate audio extension cable/s (not provided). Use the 3.5mm
Audio-In input to connect your chosen device as the source of the audio. Connect the external audio system to Audio-Out
output.

DIRECTIONS FOR USE:
When first installed or after a factory reset, the system needs to be set up. The setup process allows the discovery or
manual addition of lights connected to the DMX network and enables the user to group the lights either into a single
zone or multiple zones. The setup can be done either from the MFD via the OceanBridge App or via external devices
using the Wi-Fi connection. OceanLED recommends using an external device such as a laptop or mobile phone for
the initial setup.
QUICK START LAUNCH
For simple ‘out the box’ operation, the USB memory stick
provided with the device is pre-loaded with two standard
profiles. A single zone, with either RGBW colours lights or
dual colour lights. These simple setups will allow control of
your lights.
1. To access the quick start setup, insert the USB stick with
the setup files into the OceanBridge USB port.
2. Open the main menu and navigate to: System > Backup
& Restore, and select ‘RECALL BACKUP’.
3. Within the pop-up window, select the USB stick as the
file location, and then tap on ‘SELECT VALUE’ to display
the files.
4. Select the file related to the installed light type and
select ‘RESTORE’ to restore the setup file. Later the
system can be tailored further using the more advanced
setup outlined below.
USING THE SYSTEM
• After zones have been added they will appear on your
OceanBridge home screen.
• Light colour, mode, speed etc., can all be controlled by
selecting the individual zones.
• Configured zones are displayed, with each presented as
a separate ‘Zone Card.’ Each zone can be independently
turned on or o by pressing the toggle button on the
respective Zone Card. Additionally, by selecting the
gears icon on the zone card, you can choose the zone
eects.
• The sweep function is activated via the icon located at
the top right of the home screen.
STANDARD LAUNCH
For more advanced systems where multi-zones, dierent
light types, or sweep functionality is required, the system will
need to be setup using the following procedure:
1. From the main menu navigate to: Settings > Device
Setup, then ‘Discover’ or ‘Manual Add’ to add your
lights. ‘Discover’ will automatically discover OceanLED
E6, E7 and Sport / E3 DMX lights. For all other lights
‘Manual Add’ should be used.
2. To create zones, from the main menu navigate to:
Settings > Zone Setup, then select ‘New’ and name
your zones based on their location. You must select the
correct light type for each zone. Each light should then
be added to the relevant zone. E.g. Transom.
3. The zones will be listed on the screen and added to the
home page as zone cards, where they can be controlled.
ZONE EFFECTS
Static: For RGBW/RGB and Dual colour lights, the
required colour can be selected via the colour wheel
or colour gradient selector. For dimmable single
colour lights, brightness can be adjusted.
Cycle: Select up to four colours. Lights will transition
between each colour. Brightness and cycle fade
speed can be adjusted.
Strobe: Up to four colours can be selected, including
o. Lights will switch between these colours.
Brightness and cycle fade speed can be adjusted.
Audio Sync: Sync lights to music. Audio input via
line-in or Bluetooth.
Select four colours. Colour One = Ambient colour
(displayed in quiet periods). Colour Two = Bass tones.
Colour Three = Mid Tones. Colour Four = Treble Tones.
Overall brightness and sensitivity can be adjusted.
Movement: Lights change with the movement of the
vessel/unit.
Select five colours. Colour One = Ambient colour
(colour displayed when static). Colour Two = the -Ve
X-axis of the unit. Colour Three = the +Ve X-axis of
the unit. Colour Four = the -Ve Y-axis. Colour Five =
the +Ve Y-axis.
Ocean LED Marine LTD / Tel [phone] / [e-mail] Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.com
Specifications are subject to change without notice.
SWEEP EFFECTS
• Rainbow: The lights smoothly transition through a
sequence of up to four user-specified colours, following
the predetermined order of these colours as they move
across the light row. Users can choose the speed of
the transition to create a slow, gentle sweep or a fast,
dynamic eect.
• Knight: The lights move back and forth, resembling
a “scanner” like motion. Single colour setup. User can
control the speed of the light movement.
• Pulse: The lights move from one side to the other,
resembling the motion of a pulse. It’s a single-colour
setup. The user can control the speed of the light
movement.

Ocean LED Marine LTD / Tel [phone] / [e-mail] Ocean LED USA LLC / Tel [phone] / [e-mail] / www.oceanled.com
Specifications are subject to change without notice.
Please ensure you have read the full Installation Manual before fitting this product.
OceanBridge System Configuration Example
OceanBridge System Configuration Example Using NMEA2000 Network