Oceanled WiFi DMX TOUCH User manual

LIGHT. YEARS AHEAD. WWW.OCEANLED.COM
OceanLED MANUAL / CONTOLLERS / WiFi DMX TOUCH / REVISION 0.1
2021
INSTALLATION & OPERATION MANUAL
Wi-Fi DMX TOUCH PANEL
CONTROLLER KITS

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
1
Preface
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
WARNINGS
Before installing your DMX Controller, read and follow all warning notices and instructions which are
included. Failure to follow safety warnings and instructions can result in property damage, severe injury or
even death.
Before installing your DMX Controller, check local laws for restrictions regarding the use of coloured lights
in your area.
Salt is an inherently corrosive material. Natural and man-made surfaces are susceptible to corrosion and
deterioration when used in and around salt water. Some combinations of plastic and polymer products are
impervious to saltwater corrosion, however, screws and fasteners used for the installation must be of a
marine grade type stainless steel or equivalent and monitored annually to ensure the controller remains in
service for years to come.
Never Use Solvents! Cleaners, fuel, and other products that may contain strong solvents, such as acetone,
that attack many plastics greatly reducing their strength and can cause irreversible damage.
Units are not waterproof. You must mount in a dry location. When installing, be sure that the controller fits
the area and secures to the mounting location using the appropriate hardware before installing.
DANGER
RISK OF ELECTRIC SHOCK OR ELECTROCUTION
This unit must be installed by a licensed or certified electrician in accordance with all applicable local codes
and ordinances. Improper installation will create an electrical hazard which could result in death or serious
injury to installers, or others due to electrical shock, and may also cause damage to property. Always
disconnect the power to the light at the circuit breaker before servicing the light. Failure to do so could result
in death or serious injury to serviceman, or others due to electrical shock

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
2
Contents
1 Overview.........................................................................................................................................................................3
2 Installation.......................................................................................................................................................................4
3 Operation........................................................................................................................................................................8
4 Troubleshooting............................................................................................................................................................11
5 Warranty.......................................................................................................................................................................12
PRETEST
Alwaystestthesystempriortoinstallation.Failuretodothis mayresultinadditionalinstallationtimeandcouldinvalidate
the warranty.
IMPORTANT NOTICE
Attention Installer: This manual contains important information about the installation, operation and safe use of this
product. This information should be given to the owner and/ or operator of this equipment.
WARRANTY COVERAGE
Please refer to www.oceanled.com/downloads for full warranty statement.

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
3
1 Overview
Units are not waterproof. You must mount in a dry location. When installing, be sure that the controller fits
the area and secures to the mounting location using the appropriate hardware before installing.
1.1 TOOLS AND MATERIALS
Never use power tools. Hand tighten only!
•Drill & Drill Bits.
•Screw Driver, Phillips #2
•Wire Strippers.
•Tape measure and Ruler or Straight Edge.
•Marking Utensil (Pencil, Sharpie Magic Marker, etc)
1.2 FINDING THE MOUNTING LOCATION
•The mounting location needs to be carefully selected to ensure the unit will not be exposed to moisture.
•Ensure that the ambient temperature where the unit is mounted cannot exceed 45°C - Note that engine
compartments can easily exceed this.
•The chosen location requires access to mains power, space for the routing of the DMX cable to the driver
boxes, and also an Ethernet connection to a Wi-Fi router / LAN Wi-Fi for the Wi-Fi controller if the Wi-Fi
function is required.
For DC power installations please contact OceanLED for advice
1.3 SPECIFICATIONS
•Ready to use (pre-loaded with scenes).
•Glass Touch Panel with graphical colour display
•Micro SD Card (32Gb Max)
•6-7V DC / 100-240V AC (With Adapter)
•Environment IP20, Temp -10˚C to 45˚C
•Certifications: CE, EMC, ROHS, ETL
•Dimensions 146x106x11mm
•Weight 247g

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
4
2 Installation
2.1 CONNECT THE WIRES (EXPLORE E6 & E7)
1. Connect the control cable to the green connector (as below)
•DMX Ground = Black
•DMX - = Brown
•DMX + = Yellow
•Red wire (Unused, do not connect)
2. Connect power via the AC/DC adapter provided.
•Power DC + = Black/White Stripe
•Power DC - = Black
2.2 CONNECT THE WIRES (PRO SERIES)
3. Connect the control cable to the green connector (as below)
•DMX Ground = Brown & Brown/White (two wires)
•DMX - = Orange
•DMX + = Orange/White
4. Connect power via the AC/DC adapter provided.
•Power DC + = Black/White Stripe
•Power DC - = Black

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
5
2.3 MOUNT IN A DRY LOCATION
1. Plug the green connector block into the rear of the DMX Wi-Fi Touch Panel Controller.
2. For Wi-Fi plug the local ethernet cable into the rear of the DMX Wi-Fi touch panel controller (Ensure the correct
RJ45 port is used):
3. Mount the back plate of the interface on the preferred dry mounting location.
4. Close the unit by clipping the front panel onto the back plate.
Ethernet Port
DMX/Power
Connector

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
6
2.4 FINALISE YOUR INSTALLATION (EXPLORE E6 & E7)
Always test the system BEFORE the boat goes back into the water. Typical OceanLED light installs require
the boat to be hauled out of the water to replace light units.
The DMX standard recommends a maximum of 32 devices to be connected in one chain. If installation
requires more lights than this, please contact OceanLED for advice.
1. If Wi-Fi is required connect Ethernet cable from back of controller panel into a suitable Wi-Fi router or Wi-Fi
enabled network. (The controller is DHCP enabled as standard so should be detected by the network once
powered).
2. Connect the control cable to the control input of the first Explore E6 light. Then connect a control link cable to
the next, and so on up to the last light in the chain.
3. Fit the supplied terminator to the output of the last E6 light. See the following example of the connections:

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
7
2.5 FINALISE YOUR INSTALLATION (PRO SERIES)
Always test the system BEFORE the boat goes back into the water. Typical OceanLED light installs require
the boat to be hauled out of the water to replace light units.
The DMX standard recommends a maximum of 32 devices to be connected in one chain. If installation
requires more lights than this, please contact OceanLED for advice.
4. If Wi-Fi is required connect Ethernet cable from back of controller panel into a suitable Wi-Fi router or Wi-Fi
enabled network. (The controller is DHCP enabled as standard so should be detected by the network once
powered).
5. Connect the DMX controller DMX output cable to the DMX input of the first driver box. The DMX output of this
box should be connected to the input of the next, and so on up to the last driver in the chain.
6. Fit the supplied terminator to the output of the last driver box. See the following example of the connections:

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
8
3 Operation
3.1 POWER / SCENE SELECTION
1. Power on the unit by touching the top centre button.
2. Select the required scene by using the buttons under the ‘Select Area’ buttons below the display to select the
required area and select the scene by touching the left / right arrows either side of the display. Once the
required scene is selected, play that scene, press the ‘Play Scene’ button.
Select Scene
Select Area
Play Scene
Adjust scene speed
(use + or - on wheel
to change)
Tap to manually select colour
(of all lights in currently
selected area) –Select RGB
colour on wheel & press again
to select white channel level.
When in this mode the
indicator led in the centre of
thewheel will illuminate.
Adjust overall brightness
(use + or - on wheel to
change)
Brightness / Speed
change

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
9
3.2 PRE-PROGRAMMED SCENES –EXPLORE
Explore Dual White / Blue
Scene
Number
Function
Solid
Colours
White
White
Blue
Blue
Blue/White
Blue 50% White 50% Mix
Dynamic
Modes
White Strb
White Strobe
Blue Strb
Blue Strobe
B/W Strb
Blue / White Strobe
BW Cycle
Blue / White Cycle

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
10
Explore / Pro Series Colours
Scene
Name
Function
Solid
Colours
Red
Red
Orange
Orange
Yellow
Yellow
Green
Green
Blue
Blue
Indigo
Indigo
Violet
Violet
White
White
Red 2
Red Shade - 2
Red 3
Red Shade - 3
Green 2
Green Shade - 2
Green 3
Green Shade - 3
Blue 2
Blue Shade - 2
Blue 3
Blue Shade - 3
White 2
White Shade - 2
White 3
White Shade - 3
Dynamic
Modes
RGB Cycle
Red Green Blue Cycle
RGBW Cycle
Red Green Blue White Cycle
R-B Cycle
Red Blue Cycle
G-B Cycle
Green Blue Cycle
B-W Cycle
Blue White Cycle
G-W Cycle
Green White Cycle
R-W Cycle
Red White Cycle
R-G Cycle
Red Green Cycle
Multi Strobe
Multi Strobe
RGB Strobe
RGB Strobe –Red Green Blue Strobe
RGBW Strobe
RGBW Strobe –Red Green Blue White Strobe
R-B Strobe
Red Blue Strobe
G-B Strobe
Green Blue Strobe
R-B-W Strobe
Red Blue White Strobe
G-W-R Strobe
Green White Red Strobe

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
11
4 Troubleshooting
Wi-Fi DMX Touch Panel Controller
Problem Check Cause
Fix
DMX controller does not
power on
Check Power to
Controller is on
No Power
Connect Power
Power OK
Check Connections
Check Connections to
controller faceplate
Connected incorrectly
Correct Connections
Connected OK
Contact Warranty
Department
Lights do not respond to
controller and / or
random flickering of
lights / colours
Check DMX
connection is daisy
chained between
controller and all drivers
Not connected correctly
Correct cabling
connections
Check all other cables
are connected
correctly and are not
damaged
Not connected correctly
Correct connections
Damaged cable
Replace Cable
Check Terminator is
fitted to last driver box
Terminator not fitted
Fit terminator
Terminator fitted
Contact Warranty
Department
WiFi not working (only
applicable to wi-fi
model)
Check Ethernet cable is
connected into back of
controller panel
correctly.
Not connected
Reconnect cable
Check the controller
panel is recognised on
the connected
network.
Controller not visible
Try re-booting network
hub and controller
panel.
Check connected
network WiFi is
functioning correctly
WiFi not functioning
Resolve issue with
network WiFi
WiFi network OK
Contact Warranty
Department

CONTROLLERKITs.
2021 INSTALL & OPERATION MANUAL
12
5 Warranty
Please remove this page and keep for your files
For technical assistance:
Europe: [e-mail]
The Americas: [e-mail]
Warranty Serial Code(s):
© 2021 Ocean LED Marine LTD
All Rights Reserved
Specifications are subject to change without
notice.
Trademarks are the property of Ocean LED
Marine LTD
www.oceanled.com
Ocean LED Marine LTD
Ocean LED USA LLC
Unit 1 Jacknell Road
Dodwells Bridge Industrial Estate
Hinckley,
Leicestershire LE10 3BS
United Kingdom
778 South Military Trail
Deerfield Beach
Florida
FL 33442-3025
USA
Tel: [phone]
Fax: [phone]
[e-mail]
Tel: [phone]
Fax: [phone]
[e-mail]