OCEANSOUTH T-TOP User manual

COMPONENTS (INCLUDED IN BOX)
OPTION 01 - Front Mount OPTION 02 - Side Mount
T-TOP (MA 081) INSTRUCTIONS
TOOLS REQUIRED (Not Supplied)
lPhillips head screw driver
lCodeless Drill
lMasking tape, Tape measure & Pencil
Read the enre instrucon manual before starng, so that you are
familiar with the stages of the assembly and the tools required at each step.
12a
3a
5
6
78b8a
9a
9b
10
11
12
3b
2b
15
15c
18
19
21
21a
22
23
25
26
24
Support Arm Upright Boom
U Frame (With T Joiner)
Crossbar
Bracing Bar
Cross
Mount T-Joiner
T-Joiner
With
Hole
Fabric
¼'' x32mm
Screw
¼'' x38mm
Screw 14 Webbing Straps
Console
Mount Cap
Console
Mount Base
U Frame
Upright Top
Saddle
M6 Nut
M5 Washer
Cable
Ties
M6 Screw
M6
Allen Key
M6
Washer
ø5.0
Drill Bit
ø6.0
Drill Bit
ST4.2
Screw
Cord
2x 2x
2x 2x 2x
4Top Side Frame
2x
1x
24x
8x
8x
1x
1x
1x
1x
1x
1x
2x
1x
2x
4x
4x
15b M5 Nut
4x
4x
16x
2x
2x 2x
15a M5x25mm
Screw
4x
4x
20 Counter Sunk
Screw M6 x 80mm
16x
ATTENTION:
Determine the mounng locaon
on your console.
Two Mounng Opons
OPTION 1 - Front Mount
OPTION 2 - Side Mount
N.B It is recommended to select a
surface that is straight.
01
STEP 1- Select suitable Mounng Opon

OPTION 01 - Front Mount OPTION 02 - Side Mount
a. Select the locaon to aach the Console Mounts. b.Mark the Screw posions (16 Places)
STEP 2 - Aach Uprights to the console
c. Drill Holes (16 Places) d. Aach Console Mount Base to the console
- Tighten Screw 21 using
M6 Allen Key 21a
e. Aach Upright Boom to the console
Console Mount posions
should be placed
as high as possible
for greater stability
Align Console Mounts
with Uprights Tube
Keep the Uprights
straight and parallel
Inside the Console
18
22
(16 places)
20
9b
2b
2b
2a
2a
(8 places)
2a
9b
18
9a
21
21a
If the surface is angled,
you will need to cut the
Console Mount Bases 9b
to keep the T-Top vercal
02

STEP 4 - Assemble Frames
STEP 3 - Aach Bracing Bar to Uprights
a. Assembled
inner Top Frame
b. Drill a hole as shown in the diagram
(15mm from the edge of the Bracing Bar)
b. Aach inner Top Frame to Uprights c. Aach Top Side Frame
d. Aach U Frame (With T joiner) 3a
to the rear
3a
3a
2 Places
f. Fasten Screw 11 and 26
as shown in the diagram
e. Aach U Frame 3b to the front
11
1
4
26
3
3b
4
15mm
5.2
Ø
With Drill Bit 23
8a
8a
L
a. Cut the Bracing Bar according
to your measurement L
LL
6 6
03

a. Drill holes as shown
through aluminium tube.
(both sides)
b. Fasten Screws 12
(both sides)
c. Fasten Screws 11 (both sides)
a. Remove the top frame.
b. Posion the Fabric over the Top Frame
fasten with Cable Ties 19 as shown
c. Pass the Cord 24 through the holes as shown
d. Finish by removing the
Cable Ties 19
4 Corners
Fabric
TOP FRAME
STEP 5 - Aach the Fabric to the Top Frame
STEP 6 - Aach Top Frame back on to the Uprights
23
12
11
04

OPTION 01 - Removing the T-Top OPTION 02 - Retracng the T-Top
b. Tension the Webbing Strap 14 as shown in the diagram (2 places)
a. Fasten the Saddle 15 with 15a 15b 15c as shown
in the diagram (both sides)
IF REQUIRED T-TOP CAN BE EASILY REMOVED OR RETRACTED
Loosen
Screws
(8 places)
inside
console
d. Finish by removing the
Cable Ties 19
STEP 7 - Aach Webbing Straps
21
21a
9a
14
15
15a
15b
15c
05