Harken 944 User manual

INSTRUCTION SHEET
Halyard Restrainers
944/945/1113
N15W24983 Bluemound Rd, Pewaukee, WI 53072-4974
Telephone: [phone] • Fax: [phone]
Web: www.harken.com • Email: [e-mail]
To be used if angle between halyard and headstay is less than 7°. This
is common on masts where halyard sheave is very close to headstay.
If halyard angle is greater than 7° and halyard is still wrapping, a halyard
restrainer may not be necessary. Halyard swivel must be near top of
foils and headstay must be tight. This will prevent halyard wraps in
most cases. Consult furling instruction manual.
3. Position restrainer on mast so halyard is at a 7 to 10° angle to
headstay. See drawing on reverse side.
If necessary have a sailmaker cut down top of sail to create a 7 to 10° angle
between halyard and headstay.
With restrainer installed, halyard swivel will ride lower than installations with-
out restrainers. This is necessary to achieve correct halyard angle.
Method Rivet Tap U.S. Tap Metric
Fasteners
(not included)
(6) 3/16"
SS Rivets
(6) 10-32 x 3/8SS
Machine Screw RH
(6) 5 x .80 x 10 mm
SS Machine Screw TH
Drill Ø 13/64" (5 mm) 5/32"4.2 mm
Tap Size —10-32 5 x .80 mm
Strictly follow all instructions to avoid an accident, damage
to your vessel, personal injury or death. See www.harken.com/
manuals for additional safety information.
Tools and Supplies
Drill • Pliers • Heavy-duty rivet gun or screwdriver
Mounting Instructions
1. Hoist tallest sail that will be used.
If mast is down, angle headstay out to stemhead
chainplate (“J” dimension). Measure luff length of
tallest sail and position restrainer as directed below.
Installations aloft should be performed by rigging
professionals only. J
2. Remove sheave from restrainer, install wire and
re-fasten sheave. Note: Be careful to not lose stain-
less steel sleeve when removing sheave. Make sure
forward side of restrainer is parallel to headstay.
Do not install upside down. See drawing on
reverse side. Bend cotter pin so clevis pin will not
fall out.
Don't lose
stainless
steel sleeve
USE ONLY IF NECESSARY

Angle between
halyard and
headstay must
be 7 to 10°
Printed in USA. 4410 v1 06/23
4. Mark position of holes and drill.
This End Up
Install so
“HARKEN”
is up.
Harken equipment requires minimal maintenance, but some is required to give the best service
and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequently flushing with fresh water.
In corrosive atmospheres, stainless parts may show discoloration around holes, rivets and
screws. This is not serious and may be removed with a fine abrasive.
With the exception of winches, do not use grease unless specifically recommended in the
instruction sheets.
Maintenance
For additional safety, maintenance and warranty information see www.harken.com/manuals or
the Harken®catalog.
Warranty
WARNING! Drilling or fastening into mast may snag halyards
holding the installer aloft seriously reducing strength. Limit drill
depth and avoid fasteners protruding into mast where they may
interfere with halyards.
5. Ease halyard. Install fasteners in all six holes.
6. Tension halyard and test furling system. Do not over-tension halyard
or system will be difficult to furl.
7. If a shorter-hoist sail is used, install a pendant between sail and
halyard swivel so halyard swivel is at same height as tallest sail.