Octane Fitness Venue User manual

Seat Back Shell
B
Trim
E
Seat Cushion
C
Support Bars
F
Seat Back Cushion
A
Leg Cover
D
OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
Parts List
Scan this QR code for an
instructional video.
https://vimeo.com/340769321/
ca918e02

Washers (M12)
K
Short Pointed Screws
(5mm x 20mm)
N
Short Screws
(M6 x 25mm)
L
Hex Nut (M12)
J
Long Screws
(M6 x 40mm)
M
Concrete Anchors (M10)
Q
Plastic Caps
R
Long Pointed Screws
(5mm x 35mm)
O
Hex Screws
(M6x14mm)
P
Hardware
Tools You Will Need
Middle Chair Leg
H
Left Chair Leg
I
Right Chair Leg
G
OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
Screw DriverAllen Key Socket Wrench 3/4in
Parts List Continued

Place Right Chair Leg (G) into the desired placement (do not attach to oor). Measure 23.62” in (600mm)
then place the Middle Chair Leg (H).Measure 23.62” (600mm), then place Left Chair Leg (I). Measure-
ment is from centerline bolt to the next centerline bolt. Repeat for as many chairs as needed.
Set the Positioning
OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
GH I
23.62” in 23.62” in
Attach to the Floor
Use the Concrete Anchors (Q) to secure the feet of
the Chair Legs to the oor.
Hide the anchors by placing the Large Plastic Caps
(R) over the holes.
Important Note: Please utilize the correct hardware
for your oor type. For example, if your facility has
wood ooring you may need to use Lag bolts (not
included) in place of Concrete Anchors.
Q
Q
RR

Attach the Support Bars to the Seat Back Cushion
Align the back of the Seat Back Cushion (A) to the brack-
ets on the back of the Support Bars (F) x 2. Use the Short
Screws (L) to secure. Repeat for all seats.
Connect the Seat Back to the Chair Legs
Slide the Support Bars (F) with the Seat Back
Cushion (A) onto the Chair Leg Bolts.
OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
L
L
L
L
FF
A
FF
A

OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
Placing the Seat Cushion
Use the hinge brackets that are attached to
the Seat Cushion (C) and place them onto the
Chair Leg Bolts that are towards the front of
the Chair Legs.
Seat Cushion
C
C C
Secure the Seat Back to the Chair Legs
Use the Hex Nuts (J) and Washers (K) to at-
tach the Support Bars (F) onto the Chair Legs.
Note: At this stage only secure the back bolt.
J K
J K K J K J

OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
Attach the Leg Cover
Use the Leg Cover (D) to hide the Chair Leg Hardware
for the Middle Chair Legs (H). Use the Short Pointed
Screws (N) to Secure the back of the Leg Cover (D)
and the Long Screws (M) to secure the front of the
Leg Covers (D).
D
N
N
M
M
Securing the Seat Cushion
Use the Hex Nuts (J) and Washers (K) to at-
tach the Seat Cushion (C) to the bolts that are
towards the front of Chair Legs.
J K J K J K JK
C C

Attaching the Trim
The Trim (E) is used on the outer Left and Right Chair Legs (G) & (I). Attach the Trim (E) with Hex
Screws (P) on the corresponding Chair Legs.
EE
P
P
P
P
G I
OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
Attach the Seat Back Shell
Slide the Seat Back Shell (B) on to the Support Bars
(F) x 2 with the Seat Back Cushion (A) attached.
A
B
F
F

OCTANE
VENUE-ASSEMBLY-INSTRUCTIONS-V.2022-1
Venue Assembly Instructions
Secure the Seat Back Shell
Insert the Long Pointed Screw (O) into the hole on
the back of the Seat Back Shell (B) to secure.
A
B
O