Ocular LTE Plus User manual

Installation Guide
ocularcharging.com.au
[e-mail]
1300 912 650
Ocular LTE Plus

HOLDER
PLATE STATION
ALLEN KEY
REFERENCE PAPER
SCREWS FOR HOLDER
30mm PLASTIC BOLTS HOOK
30mm SCREWS
Station Overview
Ocular LTE Overview
Accessories of Tethered Model
LED
Display Screen
When charging: On/Off
While standby: current
adjuster button
Charging Plug

Instruction for Use
Technical Parameters
Level 2 EV Charging Station
Isolator
Wall
Button
Holder
Charging Plug
Hook
Charging Station
1 2
◆
Hang the cable on the hook when it is not in use
Make sure the wallbox is connected to power
Connect the EV and the wallbox
with the EV charging cable
Phase Mode: Single Phase
Installation Method: Wall/Stand
Certificate: CE, TUV, RCM
IP Rating: IP66
Rated Voltage: 230VAC +/- 10%
Rated Current: 32A
Maximum Power: 7.2 kW
Ambient External Temp: -25°C ~ +55°C
Enclosure Material: ABS + PC alloy
Warranty: 2 years
Phase Mode: Three Phase
Installation Method: Wall/Stand
Certificate: CE, TUV, RCM
IP Rating: IP66
Rated Voltage: 400VAC +/- 10%
Rated Current: 32A
Maximum Power: 22 kW
Ambient External Temp: -25°C ~ +55°C
Enclosure Material: ABS + PC alloy
Warranty: 2 years

Installation Guide
The cable can
be hung on the
HOOK and HOLDER
Fix the PLATE
with 30mm SCREWS
on the wall
This is the final completion pic,
you can put the HOOK
and HOLDER
anywhere you need
Wall
REFERENCE PAPER
of installing screw hole size
Drill the holes
according to the
REFERENCE PAPER
Tear off the protector
Take down the
REFERENCE PAPER
from the wall later
Hammer the
30mm PLASTIC BOLTS
into the holes
Embed STATION into
PLATE on the wall
Use Connector Clip to
connect base plate to
charger
Note: Power cables must be crimped with suitable
ferrules otherwise product warranty will be voided

1. Real-time power
2. Three Live Wire data
3. Charging Time
4. Power Consumption
5. Charging Icon
6. PCB Temperature
1. Emergency stop
2. Over Current
3. Over Temperature
4. Leakage protection
5. Short Current
of LED Status
OFF
IDLE CONNECTED
Continuous
light Rolling
CHARGING FINISHED ERROR
Red
flashing
EV Charger
00 00 06 0.00Kwh 23.7 29.4℃
℃
KW
0.00A
0.08A
0.08A Short Current
Possible
fault warning
EV Charger
0.0
L1:220V
L2:220V
L3:220V
Start-up screen
Wait for the car to be ready Stop charging and wait for
pulling out the plug
During charging process
(the version no. is for reference only)
EV AC Charger
EV Charger
EV Charger
EV Charger
EV Charger
22.8 00 00 06 0.00Kwh
22.8
23.7 00 10 00 0.00Kwh 22.8
22.8
℃
℃
℃ ℃
℃
WAITING
Connect the Charging Connector Press The Button
or use the app
Disconnect the Charging Connector
KW
0.00A
0.08A
0.08A
EV Charger
0.0
L1:220V
L2:220V
L3:220V
!
N o t e :
The Ocular LTE plus will automatically restart when minor problems occur.
For serious failures, the system cannot automatically recover. In order to remind user of this
failure, the system will automatically countdown 10 seconds to restart.
Continuous
light
Illustration of Screen and LED

Maintenance
Safety Warning
▲
▲
▲
▲
▲
MANUFACTURER
Ocular Charging
ocularcharging.com.au
[e-mail]
Ocular LTE is only recommended for use in residential applications and use outside of
this area (i.e. for commercial application) is outside of warranty.
In order to ensure the normal service life of the charging station and reduce risk, mainte-
nance must be performed every 12 months. The maintenance and installation of the
equipment must be completed by a licensed electrician. Visit ocularcharging.com.au
to book your service.
The product should be placed at an ambient temperature of -25C~+55C in relative
humidity of no more than 95%. The air should not contain acids, alkalis, or other
corrosive and explosive gases.
Ocular Charging Stations are subject to stringent quality inspections. From the day of
purchase, any problem quality can be reflected to the dealer within two years.
Any direct damage or malfunction caused by neglect, incorrect use, installation, usage,
repair by the users or natural damage are not covered by the warranty.
Regularly check whether the charging station has visible damage.
Make sure that all safety facilities are available at all times and are tested regularly to
ensure they can operate normally. Visit ocularcharging.com.au for a yearly mainte-
nance check according to Australian standards.
If a ground fault occurs, it must be assumed that the cable carries voltage. Please
confirm that there’s no high-voltage power in the system before inspecting the
charging station.
Persons who install and use charging stations must obey the principles and regula-
tions mentioned to ensure personal and equipment safety.
Before powering on the device, please confirm that the device is properly grounded to
avoid unnecessary accidents.
All tools’ unnecessarily exposed metal parts should be insulated to prevent them from
touching the metal frame to avoid short circuits.
Do not modify, retrofit, or change any part by yourself under any circumstances.
To ensure the service life and stable operation of the charging station, the operating
environment should be kept clean as possible with a relatively stable temperature and
humidity. The charging station must not be used in a flammable environment or
environments with volatile gas.
Be sure to confirm that the input voltage, frequency, circuit breakers and other
conditions of the device meet the specifications before the device is powered on
▲
▲
▲
▲

C H A R G E W I T H V I S I O N

ocularcharging.com.au
[e-mail]
1300 912 650
OCULAR LTE PLUS
USER MANUAL
OC20-BC-7.2KW-Plus
OC20-BC-22KW-Plus

Scan here for FAQs Scan here for support documents

How to charge - LTE Plus
Starting a charging session
LTE tethered model: Plug the attached charging
cable into your car port.
Stopping a charging session
To stop charging via the car please consult
your car manual.
To stop charging via the charger, simply
remove the charging plug from the port
The charging sessions can be terminated either
by the car or the charger.
Changing the charging speed
Before plugging the charging cable into the car,
press the silver button on the right side of the
charger to adjust the charging speed.
Scan for a tutorial on
the EVSE master app