OdorStop OS1000 User manual

OdorStop, LLC
5139 Southwestern Blvd,
Hamburg, NY 14075 USA
Phone: [phone]
Fax: [phone]
www.OdorStop.com
Purchase Date: ____________________________________________
Serial Number: _____________________________________________
Purchased From: __________________________________________
© Copyright 2015. OdorStop, LLC
OS1000/OS2800-080515
OS1000 / OS2800
Air Mover
OS1000
OS2800

Thank you for purchasing this OdorStop product. Please read the instructions carefully and follow all
warnings. All OdorStop products are manufactured to be simple to use and provide years of worry free
service when the recommendations in this manual are followed. Please call OdorStop at 1(888) 956-7468
with any questions or concerns.
WARNINGS
• Do not move or carry the blower while it is operating. When the blower is operating, the powerful
airow can cause unpredictable movement.
• NEVER allow children to play with or around blower.
• Do not alter or modify your blower in any way. Use only replacement parts authorized by OdorStop.
Modications or use of unauthorized parts could create a hazard and will void your warranty.
• Store blower in a clean, dry environment. Do not store outdoors or allow water inside the unit’s motor.
If the motor becomes wet, allow it to thoroughly dry before use.
• Blower should never be operated near water as it will create a risk of serious injury from electrical
shock.
• Handle unit with care to avoid causing damage or injury.
• Blower should always be operated on a at surface. Do not operate where unit could fall, or on
slippery surfaces, as this could increase the chance of injury, re, or electrical shock.
• Keep all materials, liquids, and gases from being drawn into blower and never operate unit without
factory installed safety screens in place.
• Do not use blower near combustible gas, or for circulating hot air as unit could melt and cause a re or
electrical hazard.
• Do not take blower apart or repair it unless you are qualied to do so. Never repair or service unit while
blower is plugged in.
• Make sure the air intake and outlet are free from all materials and away from obstructions, as any
restrictions may cause the blower to overheat and cause a shock or re hazard.
OPERATION
This OS1000/OS2800 high velocity air mover is designed for oor drying, water damage restoration,
and ventilation.
1) Place the blower on a level and stable surface.
2) Plug the blower into a grounded outlet with the correct voltage and amperage. For maximum
protection against electrical shock, ALWAYS use a circuit that is protected by a ground fault circuit
interrupter. If you are unsure about the outlet, check with a qualied electrician or service person.
3) Turn the switch to desired speed setting and check that the blower operates properly before
letting it run.

AUXILIARY OUTLET
This blower is equipped with a built-in GFCI that allows you to “daisy chain” together multiple units in
order to operate in large areas where power outlets are limited or not available. All other warnings for use
of this blower should be strictly adhered to.
Carpet Clamp (OS2800 Only)
This blower is equipped with a carpet clamp, which will greatly decrease the time it takes to dry carpet
and padding by blowing air under the carpet. Simply lift a corner of the carpet and place the blower at the
edge of the carpet. Secure the edge of the carpet to the blower by loosening the black knob, lifting the
clamp, and pinching the carpeting between the blower body and the clamp. Then, tighten the black knob
to hold the carpet in place. Turn the blower on and allow air to blow under the carpet.
Note: This feature cannot be used with carpet that is permanently attached to the oor (i.e. glued down,
stapled, etc.) since attempting to pull the carpet up could result in damage. Please consult a carpet
professional if unsure of how the carpet is installed.
GROUND FAULT CIRCUIT INTERRUPTER (GFCI) OUTLET
The GFCI protects the user from potential electrical shock. Should it detect a sudden ground fault, the
GFCI will interrupt the current and shut the unit o. It will also fault/trip when a short circuit or overload
occurs. If the GFCI faults/trips, unplug the unit, and look for potential hazards such as standing water,
a damaged cord, etc. Once the problem is corrected, plug unit back in, push the “Reset” button,
located on the GFCI faceplate, and re-start the blower. If blower does not re-start, please refer to the
troubleshooting section of this manual.
GROUNDING INSTRUCTIONS: This blower MUST BE grounded. Grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This blower is equipped with a cord
featuring a grounding plug which must be inserted into an appropriate outlet that is in compliance with all
local codes and ordinances. Check with a qualied electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Never modify the power cord in any way.
POWER CORD WARNINGS: Never operate units with damaged power cords or damaged extension
cords as this may lead to electrical or re hazards. Never unplug the unit by pulling the cord. Grasp the
plug rmly and pull straight out. Take precautions not to use the cord in a way where damage may occur.
Keep cords away from all water and heated surfaces. Inspect cords before each use and replace cords
that show any sign of damage.
EXTENSION CORDS WARNINGS: Extension cords must be grounded and be able to deliver the
appropriate voltage to the unit. Extension cords up to 25 feet long should use 14 AWG wire. Cords up to
50 feet long should use 12 AWG wire. When operating the unit outdoors, do not use an extension cord.

MAINTENANCE
• Inspect the electrical cord and wiring for damage or discoloration. NEVER use a blower that has a
damaged cord as it could cause an electrical shock or re.
• Inspect for loose fasteners.
• Clean safety screens of the unit.
• Listen for abnormal sounds and shut unit o immediately upon hearing unusual noises.
• Keep unit clean.
• Use compressed air or a vacuum to remove lint and other debris from the motor, inlet, or fan wheel.
• Do not use a pressure washer, water hose, or other water source to clean the unit.
• The blower has sealed bearings and cannot be lubricated. No oiling is necessary.
For information about authorized repair and maintenance call OdorStop at 1 [phone].
OS1000 SPECIFICATIONS OS2800 SPECIFICATIONS
HP: 1/5
Power: 115 Volts, 60 Hz
Switch: 3 Speed
Amps: 1.7 / 1.9 / 2.5 amps
RPMs: 1100 / 1300 / 1400
Specications are subject to change without notice.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE/SOLUTION
Blower does not turn on • Switch not turned on – turn on
• Circuit breaker or GFCI has tripped - reset
• Loose wire – tighten
• Faulty switch - replace
Blower starts and then
shuts off • Obstructed inlet/outlet – removed obstruction
• Faulty motor - replace
Blower vibrates • Motor shaft is bent – replace motor
• Fan blade is bent – replace
• Excessive dirt built up on fan blade – clean
Blower makes
scraping noise • Damaged housing – replace housing or entire unit
• Damaged fan blade – replace
• Damaged motor shaft – replace motor
Motor makes noises, but
blower won’t turn on • Damaged/faulty motor or motor shaft – replace
• Broken/loose wire to capacitor – tighten
• Damaged/faulty capacitor – replace
• Damaged housing/fan so fan will not spin – replace housing or fan wheel
• Motor shaft set screw holding fan wheel is loose - tighten
For problems not listed above, contact our service department at 1(888) 956–7468.
HP: 3/4
Power: 115 Volts, 60 Hz
Switch: 3 Speed
Amps: 4.4 / 5.2 / 6.8 amps
RPMs: 1000 / 1125 / 1500

OS1000 PARTS LIST
Ref Part Number Description Qty Req
1 OS1001 Safety Grill 1
2 OS1002 Fan Wheel 1
3 OS1003 Fan Housing 1
4 OS1004 1/5 HP Motor 1
5 OS1005 Safety Grill with GFCI Outlet 1
6 OS1006 Overload Reset Button 1
7 OS1007 GFCI Mouting Bracket 1
8 OS1008 GFCI Outlet 1
9 OS1009 Rubber Foot Pad 4
10 OS1010 Air Outlet Grill 1
11 OS1011 Switch Knob 1
12 OS1012 Switch Panel 1
13 OS1013 3-Speed Switch 1
14 OS1014 15ft Power Cord 1

OS2800 PARTS LIST
Ref Part Number Description Qty Req
1 OS2801 Plastic Safety Grill 2
2 OS2802 ¾ HP Motor 1
3 OS2803 Fan Housing 1
4 OS2804 Water Proof Connector 1
5 OS2805 Air Outlet Grill 1
6 OS2806 GFCI Outlet 1
7 OS2807 3 Speed Switch 1
8 OS2808 Switch Panel 1
9 OS2809 Carpet Clamp 1
10 OS2810 Capacitor 1
11 OS2811 Fan Wheel 1
12 OS2812 Rubber Foot Pad 2
13 OS2813 30ft Power Cord 1

LIMITED WARRANTY
OdorStop, LLC oers a limited warranty to the original retail purchaser of this product (the “unit”) against any defect
in materials and workmanship as follows: For the rst year from the date of retail purchase, OdorStop, LLC, at
its option, will replace or repair unit without charge to the customer. Any repair or replacement of the unit will be
warranted only for the balance of the original warranty period or ninety (90) days, whichever is greater. The following
will void and/or are not covered under this limited warranty: a) Damage caused by improper use. b) Opening of the unit for
any reason not authorized by OdorStop, LLC. c) Cosmetic damage or any damage caused by misuse, improper maintenance,
connection to improper voltage supply, accidents, acts of God, abuse, negligence, damage caused during shipping,
modications, or attempted repair by anyone other than OdorStop, LLC. d) Alteration or removal of factory- applied serial
number. This limited warranty is not transferable to any subsequent purchaser.
TO OBTAIN WARRANTY SERVICE: In order to obtain warranty service, the owner must return the unit in suitable
packaging, postage prepaid, to OdorStop, LLC, 5139 Southwestern Blvd, Hamburg, NY 14075, and include (i) proof
of retail purchase, (ii) the date of the failure and (iii) a description of the failure. All shipping expenses to MPI are the
owner’s responsibility.
The obligations of OdorStop, LLC herein are granted in lieu of all other warranties, expressed or implied, including
but not limited to the warranties of merchantability of tness for a particular purpose. The remedy provided in this
warranty is exclusive and is granted in lieu of all other remedies. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to you.
In no event will OdorStop, LLC be liable for loss of use of the product, loss of prots, direct damages, indirect
damages, consequential damages, and/or incidental damages by reason of injury to any person, due to any defect
or the malfunction of unit or any part(s) thereof, or for any other reason. Some states do not allow the exclusion or
limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.
This warranty gives you specic, legal rights, and you may also have rights, which vary from state to state. Owner’s
acceptance of the product and use thereof constitutes acceptance of these terms.
Warranty return address: OdorStop, LLC, 5139 Southwestern Blvd, Hamburg, NY 14075
- - - - - - - - - - - - - - Cut here and return with copy of receipt within 10 days of purchase. ------------
To register warranty, please ll out card completely and mail within 10 days of purchase with a copy of original
receipt to: OdorStop, LLC, 5139 Southwestern Blvd, Hamburg, NY 14075
Name: ________________________________________
Phone: ( ) ___________________________________ Email: ____________________________________________
City: __________________________________________ State: ________________________ Zip: ___________
Model #: ______________________________________ Serial #: __________________________________________
Purchase Date: ________________________________ Purchased From: __________________________________