Odyssey NUBEO User manual

VOL.1.84 EN/DE

EN
3
EN
This watch is equipped with a quartz powered chronograph movement.
Besides the normal time read out, this movement enables split timing
micro measurements of time at the push of a button, which can be
utilized in a variety of applications.
QUARTZ CHRONOGRAPH WATCHES

0 1 2
Hour Hand ( TIME 1 )
Chronograph
Minute Hand 24 Hour Hand
Push Button A
Push Button B
MinuteHand
Normal Crown
Crown
Positions
Chronograph Second Hand Second Hand
Date
EN
4
EN
TRIPLE TIME ZONE CHRONOGRAPH

0
12
Dual Time
24 Hour Hand
( TIME 2 )
Normal Crown
Crown
Positions
Date
Second Hand Minute Hand
Hour Hand
( TIME 3 )
EN
5
EN

EN
6
EN
1. Pull the crown out to position 2 , its maximum extension.
2. Turn the crown either clockwise or anti-clockwise until the watch hands
are positioned at the desired time.
3. When the desired time is reached push the crown back to position 0.
* Take a.m./p.m. into consideration when setting the hour and minute hands
to the desired time.
* When the crown is at the position 2, do not press any button, otherwise
the chronograph hands will move.
TIME SETTING FOR TIME 1

EN
7
EN
1. Pull the crown out to position 1.
2. Turn the crown clockwise or anti-clockwise until the desired date is shown
in the date window.
3. When the desired date is reached push the crown back to position 0.
* Do not set the date between 9:00 P.M. and 3:00 A.M., otherwise the day
may not change properly. If it is necessary to set the date during the time
period, rst change the time to any time outside it, set the date and then
reset the correct time.
DATE SETTING FOR TIME 1

1 0
Dual Time
24 Hour Hand
( TIME 2 )
EN
8
EN
TIME SETTING FOR TIME 2
1. Pull the crown out to position 1.
2. Turn the crown anti-clockwise until the 24 hour hand are positioned at
the desired time.
3. When the desired time is reached push the crown back to position 0.

12 0
Hour Hand
( TIME 3 )
EN
9
EN
TIME SETTING FOR TIME 3
1. Pull the crown out to position 2.
2. Turn the crown clockwise until the watch hands are positioned at the
desired time.
3. When the desired time is reached push the crown back to position 0.

1 0
Date
( TIME 3 )
EN
10
EN
DATE SETTING FOR TIME 3
1. Pull the crown out to position 1.
2. Turn the crown clockwise until the desired date is shown in the date
window.
3. When the desired date is reached push the crown back to position 0.
* If the date is set between the hours of
around 9:00 PM and 2:00 AM, the date
may not change on the following day.

STOP RESET
A
B
A
START
EN
11
EN
• The stopwatch can measure up to 60 minutes.
STOPWATCH FUNCTION
STANDARD MEASUREMENT

RESTART
STOP
RESET
B
A A
A
A
START STOP
EN
12
EN
Restart and stop of the stopwatch can be repeated by pressing the button A.
ACCUMULATED ELAPSED TIME MEASUREMENT

Prong-end
1. Use the Strap Tool, place the
Prong-end between the lug and
the Strap to reach the metal pin.
2. Push down to release the spring
and remove the Strap.
HOW TO CHANGE STRAP
EN
13
EN

3. Move the pins from the strap to
the new strap.
4. Place the pin end to the lug hole.
5. Use the tool again to push down
the spring so that the pin end
reaches the hole for fastening.
EN
14
EN

EN
15
EN
All Nubeo timepieces are designed with a minimum water resistance rating
of 5 ATM (50m). The water-resistance of a timepiece protects the movement
from dust, moisture, and risk of damage to the movement should it be
immersed in water.
Please see chart for guidelines for the recommended exposure of various
water ratings.
It is important not to attempt to adjust the position of the crown while the
timepiece is in contact with water. Water can enter the case causing damage
to the movement.
For timepiece with screw-down crowns, it is important to ensure the crown
is in the proper position and completely locked before contact with water.
For timepieces with chronograph functions, do not engage the chronograph
under water, as water may leak in the case and cause damage to the
movement.
WATER RESISTANT

EN
16
EN
USE PRECAUTIONS - RESISTANCE TO WATER
All Nubeo timepiece are designed to withstand use as indicated on the following
chart. Always make sure the crown is screwed-down completely before use.

EN
17
EN
Each Nubeo timepiece is designed and manufactured to exceed the highest
of standards. In order to ensure optimal performance and longevity from
your timepiece, please review the simple guidelines for care and precautions
of your new Nubeo timepiece.
CARE AND PRECAUTIONS
Your timepiece should be cleaned with a soft cloth and water only. Your
timepiece should be rinsed clean and dried with a soft cloth after any
saltwater use. In order to maintain the ‘new look’ of metal bracelets, we
recommend periodic cleanings of the bracelet. Dip a soft brush in warm
soapy water and gently rub bracelet clean. We advise having your timepiece
serviced every 18-24 months to ensure long use and trouble-free operation.
CARE

EN
18
EN
When manually winding a watch always turn the crown in a clockwise
direction.
Do not force the crown when you feel the spring become tense toward the
end of the winding process.
Daily winding is recommended even if you believe that your watch has
enough power, its always a good idea to give your mechanical watch a quick
wind before wearing it for the day.
Automatic watches can also be manually wound by turning the crown
clockwise in position 1. It is recommended that if your watch has completely
run out of power you manually wind it (with about 10 turns) before wearing.
Try to avoid exposing your watch to strong magnetic sources (for example,
smartphones, loudspeakers) as these may have an adverse effect on the
movement.
GENERAL INSTRUCTIONS FOR MECHANICAL AND
AUTOMATIC WATCHES

EN
19
EN
TWO (2) YEAR INTERNATIONAL WARRANTY
Your Nubeo watch is warranted for a period two (2) years from the original
date of purchase under the terms and conditions of the warranty. The Nubeo
warranty covers materials and manufacturing defects. A copy of the receipt
or dealer stamp in the warranty booklet is required for proof of purchase.
During the warranty period the watch movement, hands and dial are the
only components covered under this warranty. A covered component will be
repaired or the watch will be replaced free of repair charges, if it proves to
be defective in material or workmanship under normal use.

EN
20
ENNOT COVERED BY WARRANTY
- Damage to lens or strap.
- Normal wear and tear.
- Malfunction and deterioration from accident, negligence or tampering.
- Water damage resulting from improper usage.
- The content of the warranty has been altered.
- There is no presentation of the warranty.
This warranty is void if the watch has been damaged by accident, negligence
of persons other than authorized Nubeo sales or services agents, unauthorized
service, or other factors not due to defects in materials or workmanship.