OEM Tools 24887 Service manual

UNPACKING
After unpacking the unit, inspect carefully for any
damage that may have occurred during transit. Check
for loose, missing, or damaged parts. If any damage is
observed, a shipping damage claim must be filed with
the carrier. DO NOT use the OEMTOOLS™24887 4,500
CFM 3 Speed Evaporative Cooler if broken, bent,
cracked or damaged parts (including labels) are noted.
Any Evaporative Cooler that appears damaged in any
way, operates abnormally or is missing parts should
be removed from service immediately. If you suspect
that the Evaporative Cooler was subjected to shock
load (a load that was dropped suddenly, unexpectedly,
etc.), immediately discontinue use until it has been
checked by a factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself
and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in
personal injury and/or damage to product or property. Please retain instructions for future reference.
Operating Instructions and Parts Manual 24887
1/18
2018 OEMTOOLS™
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
4,500 CFM 3 SPEED
EVAPORATIVE COOLER
Thank you very much for choosing an OEMTOOLS™Product!
For future reference, please register your new product at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS™cannot be responsible for issues arising
from modification. We strongly recommend this product is not modified and/or used for any application other than that for which it was
designed. If you have any questions relative to a particular application, DO NOT use the product until you have first contacted customer
service to determine if it can or should be performed on the product.
WARNING: Pursuant to California Proposition 65, this product contains chemicals known to the state of California to cause
cancer and birth defects or other reproductive harm. Wash hands after handling.
The following safety information is provided as a guideline to help you operate your Evaporative Cooler under the safest possible conditions.
Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed.
The following safety instructions are to provide the user with the information necessary for safe use and operation. Please read and retain these
instructions for the continued safe use of your Evaporative Cooler. Failure to follow instructions listed below may result in serious injury. In addition,
make sure that anyone who uses the equipment understands and follows these safety instructions as well.
WARNING
EXPLANATION OF SAFETY SIGNAL WORDS
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES: Provide clarity and helpful information.

2
Operating Instructions and Parts Manual 24887
4,500 CFM 3 SPEED
EVAPORATIVE COOLER
1/18
2018 OEMTOOLS™
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn the product’s
applications and limitations, as well as potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark work areas invite
accidents.
3. Keep children away. All children should be kept away from the work
area. Never let a child handle tools or equipment without strict adult
supervision.
4. DO NOT operate this product if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, DO NOT
attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses. Everyday
eyeglasses are NOT safety glasses. Dust mask, non-skid safety
shoes, hard hat or hearing protection should be used in appropriate
conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings, bracelets
or other jewelry may present a potential hazard when operating this
product. Keep all apparel clear of the product.
7. DO NOT overreach. Keep proper footing and balance at all times when
operating this product.
8. Check for damage. Check equipment regularly. If part of the product
is damaged, it should be carefully inspected to make sure that it can
perform its intended function correctly. If in doubt, discontinue use of
product.
9. Keep away from flammables. DO NOT attempt to operate this product
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10.Store this product out of the reach of children and untrained persons.
This product may be dangerous in the hands of untrained users.
11. Keep this product dry and clean.
12.Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one product may
become hazardous when used on another product.
13. Service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a
risk of injury.
14. When servicing a product, use only identical replacement parts. Use of
unauthorized parts or failure to follow maintenance instructions may
create a risk of injury.
15. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the work
area free of obstructions, grease, oil, trash, and other debris. Do not
use this product in a damp or wet location.
16. Maintain labels and nameplates on this product. These carry important
information. If unreadable or missing, contact OEMTOOLS™for a
replacement.
17. Keep this product dry, clean, and free from brake fluid, oil, and grease.
18. Avoid accidental fire. DO NOT smoke near this product.
19. The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur. The
operator must understand that common sense and caution are factors
which cannot be built into this product, but must be supplied by the
operator.
20. We believe the information contained herein to be reliable. However,
general technical information is given by us without charge and the
user shall employ such information at their own discretion and risk.
We assume no responsibility for results or damages incurred from the
use of such information in whole or in part.
21. The manufacturer declines any and all responsibility for property
damage or injury if said damage is the result of unskillful handling by
the operator or of failure to observe the basic safety rules set forth in
the instruction manual.
22.The procedures documented in this manual are to serve as guidelines
for the use of this equipment.
23.The use of this equipment is simple and straightforward if you follow
the instructions. When operating this equipment, use common sense,
and only use this equipment for its intended purpose.
PRODUCT DESCRIPTION
The OEMTOOLS™24887 4,500 CFM 3 Speed Evaporative Cooler
is designed to efficiently cool workspaces. This Evaporative Cooler
pulls hot surrounding air through wet cooling pads, where through
process of evaporation, the air is cooled. The powerful 0.25 HP fan
then pushes the cooled air at 4,500 CFM into the surrounding area—
cooling spaces up to 1,300 ft².
PRODUCT SPECIFICATIONS
Motor Power 0.25 HP
Input Voltage 110V AC, 1-Phase
Speed Settings 3
Max Air Volume 4,500 CFM
Water Capacity 14.6 Gallons
Cooling Area Up to 1,300 ft²
Run Time Up to 4 Hours
Dimensions 45"(L) x 28"(W) x 17"(H)
Dry Weight 58 Lbs.
CONTENTS
(1) Evaporative Cooler, (4) Casters, (1) Instruction Manual
SPECIFIC SAFETY INSTRUCTIONS AND WARNINGS
WARNING: Thoroughly read and understand the provided product
manual before attempting to use this product.
1. DO NOT touch the Evaporative Cooler when your hands are wet.
2. DO NOT disassemble, repair or rebuild the Evaporative Cooler. Contact
qualified personnel for any maintenance extending past the instruction
provided by this manual.
3. Unplug the Evaporative Cooler when it is not in use.
4. Unplug the Evaporative Cooler before moving it or performing
maintenance.
5. DO NOT unplug the Evaporative Cooler by holding the cord. Unplug by
holding the plug.
6. DO NOT use the Evaporative Cooler when there is damage to the cord
or plug. Discard the Evaporative Cooler or return to an authorized
service facility for examination and/or repair.
7. Avoid the use of extension cords when possible. Ensure that they
are UL listed if they must be used. DO NOT use a single extension
cord to operate more than one Evaporative Cooler. DO NOT plug the
Evaporative Cooler into any other cord-connected device (power strip,
surge protector, multiple outlet adapters, etc.).
8. DO NOT use the Evaporative Cooler close to any fire or heat source.
9. DO NOT insert your hand or other objects into the rear housing when
the blade is moving.
10.To reduce the risk of fire or electric shock, DO NOT use this
Evaporative Cooler with any solid-state speed control device.
11.DO NOT run cord under carpeting. DO NOT cover cord with throw rugs,
runners, or similar coverings. DO NOT route cord under furniture or
appliances. Arrange cord away from traffic area and where it will not
be tripped over.
12.DO NOT submerge the Evaporative Cooler in liquids.
13.Confirm the rear panel is attached prior to operation.
14.ALWAYS place the Evaporative Cooler on a flat, level surface.
15.DO NOT expose electrical connections to water.
16.DO NOT touch electrically live components.
17.DO NOT open the electrical box while the product is in use.
18.Ensure adequate ventilation.

3
Operating Instructions and Parts Manual 24887
4,500 CFM 3 SPEED
EVAPORATIVE COOLER
1/18
2018 OEMTOOLS™
ASSEMBLY INSTRUCTIONS
The OEMTOOLS™24887 4,500 CFM 3 Speed Evaporative Cooler is pre-
assembled. Carefully remove the Evaporative Cooler from the Box. Install
the (4) casters.
PREPARING FOR OPERATION
IMPORTANT: Read and understand the provided safety instructions prior
to operation.
1. Before attempting to use, inspect the filter for dirt, dust or residues.
Cooling pads that have accumulated build-up will impede cooling
performance.
2. To operate effectively, position the unit in front of an open door or
window. Ensure the unit is placed on a flat, level surface with the
casters in the locked position.
3. Open another door or window to provide proper ventilation for the unit.
MANUAL FILL
1. Depress the Fill Door located on the front of the unit below the louvers
(the Fill Door features a spring lock, and will release when pressed).
2. Fill the Water Tank using a hose or bucket. Monitor water level using
the Fill Gauge.
3. Press the Fill Door closed (the spring lock with re-engage).
AUTOMATIC FILL CONNECTION
NOTE: This unit features a float valve and automatic shut-off function.
This allows the unit to remain connected to an open water source for a
continuous flow of water. The operator may also fill the Water Tank to
capacity (or desired level) prior to running the unit, and then close the
water source.
1. Attach the provided Pigtail Adapter to the Water Inlet.
2. Connect one end of the provided Coil Hose to the Pigtail Adapter.
3. Connect the other end of the Coil Hose to a water supply. Ensure that
both connections are water tight.
OPERATING INSTRUCTIONS
1. Plug the unit into a grounded 110-120V AC outlet.
NOTE: This Evaporative Cooler is equipped with a UL Ground Fault Circuit
Interrupter (GFCI) Plug. This UL GFCI Plug is designed to interrupt power
to the unit if current follows an unintended path. This feature is a safety
measure to reduce risk of electric shock to the operator and electrical
damage to the Evaporative Cooler. If the circuit is tripped, press the Reset
Button located on the plug head. If the Reset Button will not engage and
power is not restored, discontinue use, see the troubleshooting section for
further instruction.
2. Open the water source to fill the Water Tank. Monitor water level using
the Fill Gauge; allow the Water Tank to reach 50% capacity.
WARNING:Water Inlet pressure should not exceed 50 PSI. Higher
pressure may lead to product failure and property damage.
3. Switch the Power to ON.
4. Switch the Pump to ON. Allow to run for 2-3 minutes to saturate the
Cooling Pads with water.
NOTE: The pump will automatically shut-off when the water level is low.
5. Switch the Fan to the first speed setting. Allow to run at the first speed
setting for 2-3 minutes. Increase the speed of the fan to the desired
setting: Off, Low, Medium and High.
6. To oscillate airflow, switch the Swing Setting to ON.
SHUTDOWN INSTRUCTIONS
1. Close the water source.
2. After the Water Tank has emptied, switch the Pump to OFF.
NOTE: See Draining Instructions if the Water Tank is not empty.
3. At the end of each day of use, allow the Fan to run for about 20
minutes to dry the Cooling Pad(s).
4. Switch the Fan to OFF.
5. Switch the Power to OFF.
6. Unplug the Power Cord from the power source.
DRAINING INSTRUCTIONS
1. Turn the Power to OFF, and ensure the unit is not plugged into a power
source.
2. Move the unit outdoors or position the unit over a drain.
3. Unscrew the Drain Cap from the Drain Assembly. Allow the water to
completely drain from the Water Tank.
4. Replace the Drain Cap to the Drain Assembly.
STORAGE
Store the Evaporative Cooler in an upright position and in a clean, dry
area. DO NOT store near flammable items or open flames.
DISPOSAL
At the end of the useful life of the OEMTOOLS™24887 4,500 CFM 3
Speed Evaporative Cooler, dispose of the components in accordance with
all federal, state and local regulations.
PRODUCT MAINTENANCE
WARNING:Unplug this unit from the power source before
performing product maintenance.
WARNING:DO NOT use water to clean the Fan, Electrical
Components or Control Panel.
WARNING: DO NOT attempt to perform product maintenance on
the motor or electrical systems. If there is any doubt that this unit can
perform safely, immediately discontinue use and contact customer
service.
1. Dirt and debris will settle at the bottom of the Water Tank. To optimize
performance, it is recommended that the Water Tank is cleaned
monthly.
2. To maintain high air quality, it is recommended that the water is
flushed from the Water Tank daily.
3. Inspect the cooling pads prior to each use. If dirt, debris or build-up is
present, remove the cooling pad and gently wipe clean. Replace the
cooling pad to the unit.
NOTE: The Cooling Pads are constructed with a special resin impregnated
craft paper specifically designed for this evaporative cooler. If the unit
is used in accordance with this product manual, and the cooling pads
are properly maintained, they will last several years (under normal
circumstances).
PRODUCT LAYOUT
ITEM DESCRIPTION QTY. ITEM DESCRIPTION QTY.
A Control Panel 1 I Fill Gauge 1
B Oscillating Blades 11 J Cooling Pads* 2
CFan 1 K GFCI Plug* 1
DVertically Adjustable Louvers 11 L Water Inlet* 1
E Manual Fill Door 1 M Pigtail Adapter* 1
FWater Tank 1 N Coil Hose* 1
G Swivel Caster 2 O Water Drain Assembly* 1
H Locking Caster 2
G
F
E
D
C
B
A
I
H
*Not Shown

4
Operating Instructions and Parts Manual 24887
4,500 CFM 3 SPEED
EVAPORATIVE COOLER
1/18
2018 OEMTOOLS™
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS™90 DAY LIMITED WARRANTY
For 90 days from the original purchase of this product, OEMTOOLS™will warranty this item. If you find any defect in material or workmanship, through
normal usage, return it to the place of purchase or to OEMTOOLS™for repair or replacement at our discretion. In order to obtain this service, send your
tool and proof of purchase, transportation pre-paid, to OEMTOOLS™Q.A. Dept., 3850 Raines Road #3, Memphis, TN 38118. We will not be responsible
for lost or damaged goods during transportation; please insure your package. If our inspection verifies the defect, we will either repair or replace the
product at our election, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty,
then you must bear the cost of returning the product.
OEMTOOLS™does not provide warranty for products labeled other than OEM®or OEMTOOLS™. OEMTOOLS™will not provide any warranty for products
subjected to abnormal use. Abnormal use includes, but is not limited to, abuse, accident, alteration, neglect, and unauthorized or unreasonable use or
repairs. This warranty does not cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace
blades, bits, files, and batteries as necessary. OEMTOOLS™reserves the right to make any changes in construction or design at any time without any
obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS™makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original purchaser that
this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Don’t forget to register your new OEMTOOLS™product at www.oem-tools.com.
PROBLEM POSSIBLE CAUSE COURSE OF ACTION
Unit does not start and power indicator light
does not illuminate
Electricity is not supplied to unit
Check power supply and outlet
- Reset breaker
- Contact a qualified electrician
Unit is experiencing motor or electrical failure Contact customer service
Unit output is irregularly low or diminished
Cooling Pad is not fully saturated
Allow Pump to run for 2-3 minutes prior to
starting the Fan
Cooling Pad is not properly inserted, assess and
correct
Cooling Pad requires a break-in period for
optimal absorption; this may take up to one
week of use
Water Tank is empty Check hose connection and water source
Pump is clogged or has malfunctioned Contact customer service
Knocking/shaking sounds from Fan or Motor Loose parts or fasteners
Tighten any visible loose fasteners on the
exterior of the unit; contact customer service if
sounds persist
Excessive water droplet output from Fan Cooling Pad is not properly inserted Assess and correct placement
Musty odor present* †
Stagnant water in Water Tank Drain water completely, clean the Water Tank
and replace with fresh water
Dirt, dust and debris are present on Cooling Pad Gently wipe and clean Cooling Pad; contact
customer service if smell persists
* If a burning smell is noticed, discontinue use and contact customer service before attempting to use.
† A slight, unpleasant odor may be noticed during the first few uses. This is normal and a result of manufacturing processes.
TROUBLESHOOTING