OEM Tools 24960 User manual

29-inch Portable Tray
CAUTION:
1. Read and follow all safety information and instructions before using this
product for the first time.
2. Fill in the following information and retain the manual for future reference:
Model #: Place of purchase:
Date of purchase: Receipt # of purchase:
CAUTION: TAKE SAFETY PRECAUTIONS WHEN USING YOUR TEAR DOWN TRAY
24960
204JGT050BLK

2
SAFETY & PArTS liST
SAFETY
WARNING: READ ALL SAFETY
INSTRUCTIONS BEFORE ASSEMBLING
AND USING THIS PRODUCT.
• WEARSAFETYGLASSESAND
GLOVESwhenassemblingthisproduct.
• DONOTstandonthisproduct.You
may fall, which may cause personal
injury.
• DONOTalterthisproductinany
manner. For example, do not weld
external lock bars or attach electrical
equipment to it. This may cause
product damage or personal injury.
• BECAREFULofsharpedges.
• Keeptheproductonalevelsurface.
The product may become unstable
andtipifstoredormovedonatilted
surface, and may cause personal injury
or product damage.
• CAUTION: The load capacity, at
lowered height, is 220 lbs (100 kg). For
every2in(50mm)thetrayisraised,the
loadcapacityreducesby11lbs(5kg).
Do not exceed the load capacity of this
unit.
• ALWAYSWEARANSI-approvedsafety
goggles when working with tools and
equipment.
PARTS LIST
A
b
c
d
e
f
g
h
i
j
k
l
Part Description Qty
ATop tray 1
BRubber corner bumper
with pins
4
CSmallplasticinsert 4
DM8 x 14 bolt and washer 8
EAdjustabletube(silver) 1
FT-bolt 1
GRight support 1
HLargeplasticinsert 4
I2" Castor with nut 4
JTube support 1
KLeftsupport 2
LM10x18mmBoltwith
curvedwasher
1
MEVAmats 4
NBolts 9

ASSEMBlY
3
STEP 1:
Using four 14 mm bolts, washers and
nuts, install one caster in each square
hole on the bottom edge of both the
right and left support G& K.Besurethe
square bolster on the post of each castor
inserts fully into the square hole in the
support before tightening.
STEP 2:
Using four 14 mm bolts and washers,
attach the bolt plate on the right support
Gto the bracket on the tube support
J, ensuring that the castors are facing
down.Besureboltsaresecurely
tightened before proceeding.
STEP 3:
SlideleftsupporttubeKinto the tube
support Jand secure with 17 mm
boltandcurvedwasherL.Thecurved
washer should lay flat against the tubing.
STEP 4:
LayingthetoptrayAupside down on
the floor, attach the mounting bracket
onsilveradjustingtubeEto the bracket
on the bottom of the tray, being sure the
grooveintheadjustingtubefacesaway
from the center of the top tray.
STEP 5:
Now,slidethesilveradjustingtube
with the top tray attached into the tube
support Jand secure at the desired
heightwiththeT-boltF.
STEP 6:
Attach four rubber protector bumpers
Bby pushing the black plastic pins
providedintotheholesinthecornersof
the top tray. The pins are inserted from
outside the tray toward the inside, being
suretherubberbumpersoverlapthetop
edge of the tray.
STEP 7:
Install the four small rectangular plastic
inserts Cinto the reinforcement bars
under the top tray. Then install the
four large rectangular plastic inserts H
into the four holes on the left and right
supports G& K.
Youarenowreadytouseyournew
portable tray.