OENOPRO TGLSST-RHSSSH-SZ User manual

1
INSTRUCTION MANUAL
FOR WINE COOLER/BEVERAGE COOLER
MODEL
TGLSST-RHSSSH-SZ TGLSST-LHSSSH-SZ TFGBLK-RHWDSH-SZ TFGBLK-LHWDSH-SZ
Thank you for purchasing our Wine Cooler/Beverage Cooler. It is our hope you will find years of
joy in collecting and aging your fine wines. Before use, please read and follow all safety rules and
operating instructions.

2
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire, electrical shock, or
injury when using your appliance, follow
these basic precautions:
Read all instructions before using the wine cooler.
DANGER or WARNING: Risk of child entrapment.
Child entrapment and suffocation: Abandoned appliances are still dangerous, even if
they will “sit in the garage for a few days only”.
Before you throw away your old Wine C
ooler/Beverage Cooler: Take the door off. Leave the shelves in place so that children
may not easily climb inside.
Children should be supervised to ensure that they do not play with the appliance.
Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or
explosion.
Do not store explosive substances such as aerosol cans with a flammable propellant in
this appliance. The fumes can create a fire hazard or explosion. Do not store explosive
substances such as aerosol cans with a flammable propellant in this appliance.
WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
WARNING: Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer.
To avoid a hazard due to instability of the appliance, it must be fixed in accordance with
the instructions.
WARNING: Do not damage the refrigerant circuit.
WARNING: Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
If the refrigerant of these appliances are R600a , flammable and explosive articles
should not be placed in or near the cabinet, to avoid both fire or explosions.
-Save these instructions-
To prevent damaging the door gasket, make sure to have the door all the way
opened when pulling shelves out of the rail compartment.
The appliance must be positioned so that the plug is accessible. Release the electric
cord. Move your cabinet to its final location. Do not move your cabinet while
loaded with wine. You might distort the body. The wine cellar should be installed in
a suitable place to avoid touching the compressor with your hands.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid hazard.
PLEASE DO NOT TRY TO PLUG INTO OR USE AN EXTENSION CHORD.

3
INSTALLATION INSTRUCTIONS
Before Using Your Wine Cooler/Beverage Cooler
Remove the exterior and interior packing.
Before connecting the Wine Cooler/Beverage Cooler to the power source, let it stand
upright for approximately 24 hours. This will reduce the possibility of a malfunction in the
cooling system from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
This appliance is intended to be used in household and similar applications such as
–staff kitchen areas in shops, offices and other working environments;
–residential homes and by clients in hotels, motels and other residential type environments;
–bed and breakfast type environments;
–catering and similar non-retail applications.
When disposing your appliance, please choose an authorized disposal site.
Installation of Your Wine Cooler/Beverage Cooler
This appliance is designed to be used for a free standing installation or built-in (fully
recessed. Refer to sticker location on the back of this appliance).
This appliance is intended to be used exclusively for the storage of wine or
beverages.
Place yourWine Cooler/Beverage Cooler on a floor that is strong enough to support it when
it is fully loaded. To level your Wine Cooler/Beverage Cooler, adjust the front leveling leg at
the bottom of the Wine Cooler/Beverage Cooler.
This appliance is using flammability refrigerant. Never damage the cooling pipework during
transportation. Locate the Wine Cooler/Beverage Cooler away from direct sunlight and
sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating
and heat sources may increase electrical consumption. Extreme cold ambient temperatures
may also cause the unit not to perform properly.
Avoid locating the unit in moist areas.
Plug the Wine Cooler/Beverage Cooler into a dedicated, properly installed-grounded wall
outlet. Do not under any circumstances cut or remove the third (ground) prong from the
power cord. Any questions concerning power and/or grounding should be directed toward a
certified electrician or an authorized service center.
Attention
Store wine in sealed bottles;
Do not overload the cabinet;
Do not open the door unless necessary;
Do not cover shelves with aluminum foil or any other shelf material which may prevent air
circulation;
Should the Wine Cooler/Beverage Cooler be stored without use for long periods, it is
suggested, after a careful cleaning, to leave the door ajar to allow air to circulate inside the
cabinet in order to avoid possible formations of condensation, mold or odors.
Ambient Room Temperature Limits
This appliance is designed to operate in ambient temperatures specified by its temperature class
marked on the rating plate.
Class
Symbol
Ambient Temperatures range(℃)
Extended Temperate
SN
﹢10 to﹢32
Temperate
N
﹢16 to﹢32
Subtropical
ST
﹢16 to﹢38
Tropical
T
﹢16 to﹢43

4
Description of product number
OPERATING YOUR WINE COOLER/BEVERAGE COOLER AND SETTING THE
TEMPERATURE CONTROL
Control System Instruction
Power switch : Press for 3 seconds to turn the unit on or off.
℃/℉switch: Press ℃/℉button to change the temperature display between Celsius and
Fahrenheit.
Temperature setting button : Press before adjusting the temperature. When
pressing it for the first time, the display flashes and shows the setting temperature. After 5
seconds, it shows the measured interior temperature. Press to increase the setting
temperature and press to decrease the setting temperature.
Display window: 2-digit LED display to show setting temperature or actual interior temperature.
Light button : Press to turn on or off. The light will be automatically on when
opening the door.
Key lock function: If there is no any operation with digital control for 3 minutes, it will be locked
automatically. Press and at the same time for 3 seconds to unlock.
Setting The Temperature Controls
You can set the temperature as you desire by pushing the “+”or “-”button. When you push the
two buttons for the first time, the LED readout will show the original temperature set at the
previous time.
The temperature setting you desire will increase 1ºC if you push the“+”button once, on the
contrary the temperature will decrease 1ºC if you push the “-” button once.
To view the “set” temperature, (anytime) press and hold the corresponding button for
approximately 5 seconds, the “set” temperature will temporarily “flash” in the LED display for 5
seconds.
Control System Instruction

5
Power switch : Press for 3 seconds to turn the unit on or off.
℃/℉switch: Press ℃/℉button to change the temperature display between Celsius and
Fahrenheit.
Temperature setting button : Press before adjusting the temperature. When
pressing it for the first time, the display flashes and shows the setting temperature. After 5
seconds, it shows the measured interior temperature. Press to increase the setting
temperature and press to decrease the setting temperature.
2 Display window: 2-digit LED display for each to show setting temperature or actual
interior temperature.
Light button : Press to turn on or off. The light will be automatically on when
opening the door.
Key lock function: If there is no operation with digital control for 3 minutes, it will be locked
automatically. Press and at the same time for 3 seconds to unlock.
Setting The Temperature Controls
When pressing the temperature setting button “+” or “-“, the system will enter in set up
mode of the upper or lower compartment automatically. The LED display will flash and
show the setting temperature. After 5 seconds, the flash will stop and it will show the actual
measured interior temperature.
Press the button once, the temperature will decrease or increase 1 ℃. After 5 seconds of
not pressing the buttons, the LED figure will stop flashing, then revert back to displaying
the setting temperature of the upper or lower compartment.
After the unit is unplugged, the system will return to its default setting temperature, which
is set by the factory. The default setting temperature is as below:
Upper compartment: The temperature setting can be adjusted from 12℃to 20℃.
Lower compartment: The temperature setting can be adjusted from 5℃to 12℃.
the temperature difference between upper and lower zones needs to be at least 4°C
Attention
If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes
before restarting the unit. If you need to restart before this time delay, the Wine
Cooler/Beverage Cooler will not start. If it is a first time use or longer absence before using,
the temperature will differ between the setting and LED display temperature. After running
for a period, the temperature will revert.
Shelves
To prevent damaging the door gasket, make sure to have the door opened all the way
when pulling shelves out of the rail compartment.
For easy access to the storage content, you must pull the shelves approximately 1/3 out of
the rail compartment; however, this unit is designed with a notch on each side of the shelf
tracks to prevent bottles from falling.
Please refer to the following directions for replacing shelves with a different method.
Type A
If needing to remove shelves, move the shelf towards the gap on both sides and align with
shelf support A. Then lift shelf upwards and pull from the cabinet, once the shelf support
has disengaged from the gap.

6
A
A
Type B
When removing a shelf from the rail compartment, to fit or remove it, tilt the shelf as per the
diagram and simply pull out, or push in, until the shelf sits on the support brackets
securely.
Reverse the door with visible hinge
This appliance has the option of the door opening from either the left or right side. The unit
purchased has the door opening from the side you have specified. Should you desire to
reverse the opening direction, please follow the below instruction.
1 2

7
3 4
①Lock screws ②Lower hinge(Right) ③Door axis
④Top hinge(Right) ⑤Door ⑥Cabinet
⑦Top hinge(Left) ⑧Lower hinge(Left)
Unscrew the Lock screws ①；(please see picture 1)
Pull the door ⑤outward，take it out (please see picture 2)
Unscrew 3 bolts as indicated, take out the Top hinge(Right)④；(please see picture 3)
Fix the Top hinge(Left) and Lower hinge(Left) with bolts on the position as picture shows,
Change the door alarm parts
①Door ②lock ③door alarm magnet ④magnet fix hole ⑤lock fix hole
1. After changing the door，first unscrew ②lock and ③magnet like Image 1；
2.Then fix the ②lock to the position of ⑤lock hole
3. After changing this, affix ③magnet to the position of ④magnet hole.

8
Installation diagram:
UNPACKINGAND CLEANING THE WINE COOLER
Remove the exterior and interior packing materials.
Let the appliance stand upright for approximately 24 hours before connecting it to the
power source. This helps reduce the possibility of a cooling-system malfunction from
handling during transportation.
Use a soft cloth to clean the interior surface with lukewarm water.
Install the door handle provided with the appliance by following these steps:
Step 1 －Remove the gasket at the inner side of the door
to expose the two screw holes.
Step 2 －Install the handle securely with the
screws and washers provided.
Be sure not to overtighten on full glass models as
this can crack the glass.
Step 3 －Tidy and restore the gasket. If gasket
shows gaps or warping, use a blow dryer to
gently heat the gasket back to its original shape.

9
LOCK & UNLOCK THE DOOR (FOR OPTION)
Lock is an optional function. If your Wine Cooler has such function, a key is attached inside
the packing of this Manual.
Insert the key into the lock and turn it counter-clockwise to unlock the door. To lock it, please
follow the reverse operation. Please save the key.
CHARCOAL FILTRATION SYSTEM
Your wine is living and breathes naturally through its cork. In order to preserve the quality and
taste of your fine wines, they must be stored at the ideal temperature and ambient conditions.
Your cellar is equipped with an active charcoal filtration system to ensure air purity, cooling
efficiency, and to maintain an odor free cabinet for the storage of your fine wines. The filtre
assembly is located at the rear panel, inside your cellar.
Keep in mind, this filtre must be changed every 12 months.
To replace your filter:
1
Remove the bottles of wine stored on the two (2)
shelves in front of the filtre.
Turn left to remove filtre.
2
Remove the shelves and set aside to be
replaced once you have changed the filtre
3
Hold the filtre, turn it at 45 degrees in the
counter-clockwise direction, and then pull it out.
4
Remove the existing filtre and replace with a
new one.
5
Put the new filtre into the hole and then turn the
filtre at 45 degrees in clockwise direction.
CARE & MAINTENANCE
Clean your Wine Cooler/Beverage Cooler
Turn off the power, unplug the appliance, and remove all items including shelves and rack.
Wash the inside surfaces with warm water and a mild solution.
Wash the shelves with a mild detergent solution.
Wring excess water out of the sponge or cloth when cleaning area of the controls, or any
electrical parts.
Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe
dry with a clean soft cloth.
Power Failure
Most power failures correct themselves within a few hours and should not affect the
temperature of your appliance, if you minimize the number of times the door opens. If the
power will be off for a longer period, you will need to take the proper steps to protect your
contents.
Vacation Time
Short vacations: Leave the Wine Cooler/Beverage Cooler operating during vacations of

10
less than three weeks.
If the appliance will go unused for several months, remove all items and turn off the
appliance. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave
the door open slightly: blocking it open if necessary.
Moving your Wine Cooler/Beverage Cooer:
Remove all items.
Take out loose items inside the Wine Cooler/Beverage Cooler (such as shelves), or fix the
loose items with foam.
Turn the adjustable legs up to their base to avoid damage.
Tape the door shut.
Be sure the appliance stays secure in the upright position during transportation. Protect
outside of your appliance with a blanket or similar items.
Energy Saving Tips:
The Wine Cooler/Beverage Cooler should be located in the coolest area of the room, away
from operating appliances, and out of direct sunlight.
PROBLEMS WITH YOUR WINE COOLER/BEVERAGE COOLER
Troubleshooting Guide
Problem
Possible Cause
Wine Cooler/Beverage Cooler does
not operate
Not plugged in.
The appliance is “OFF.”
The circuit breaker tripped or a fuse is blown.
Wine Cooler/Beverage Cooler
is not cold enough
Check the temperature control setting.
External environment may require a higher
setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Turns on and off frequently
The room temperature is hotter than normal.
Overloading of the cabinet
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work
Not plugged in.
The circuit breaker tripped or a fuse is blown.
The bulb has burned out.
The light button is “OFF.”
Vibrations
Check to be sure the Wine Cooler/Beverage
Cooler is level.
Too much noise
A rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling.
Contraction and expansion of the inside walls
may cause popping and crackling noises.
The Wine Cooler/Beverage Cooler is not level.
The door will not close properly
The Wine Cooler/Beverage Cooler is not level.
The door was reversed and not properly installed.
The gasket is dirty or warped.
The shelves are out of position.

11
Before disposal of the appliance.
1. Disconnect the main plug from the main socket.
2. Cut off the main cable and discard it.
Correct Disposal of this product：
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle you appliance responsibly to promote the sustainable reuse of material
resources. To return your used device, please use your local return/collection systems or
contact the retailer where the product was purchased. They may refer you to environmentally
safe, recycling centres in your area.