Office Star Products 583814 User manual

FEATURES
• SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever
(1). To lower seat height sit on chair and lift lever (1).
NOTE: It is normal for chair to slightly lower under
body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped
with an adjustment that will allow the user to change
the tension of the tilting feature. Turn knob (2)
clockwise to increase tension and counter-clockwise
to decrease or ease the tension. To lock return chair
to the upright position and push lever (1) in. To unlock
pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment
knob completely.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, lift lever (3) adjust arm to desired
height, release lever (3) to lock arm into postion.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing
tension.
5. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
LIMITED WARRANTy
Ofce Star chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 5 Years on all non-moving metal parts.
• 2 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 1 Year on upholstery fabric and foam against wear and deterioration.
• We cannot warrant leather against routine scratching and scufng, as all leather is subject to minor blemishes in normal
use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and
obtain return authorization. At it’s option Ofce Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component. The customer must prepay freight on any components returned to the factory. Return
freight on components still in warranty will be paid by Ofce Star Products.
*All warranties are limited to the original purchaser for normal Residential usage by persons weighing 200 lbs. or less. This warranty will not cover labor,
freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star
Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The
user assumes all risk of injury resulting from use of this product. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00
p.m. Pacic Time.
583713/583814 MESH BACK CHAIR
OPERATING INSTRUCTIONS
583713
583814
1
2
3
1
2
3

583713/583814 MESH BACK CHAIR
ASSEMBLY INSTRUCTIONS
© Office Star Products November 2006
PART QTY
1. Base ....................1
2. Casters ..................5
3. Pneumatic Cylinder . . . . . . . . . 1
4. Mechanism ...............1
5. Seat Cushion . . . . . . . . . . . . . . 1
6. Back Assembly . . . . . . . . . . . . 1
7. Arms (7L & 7R) . . . . . . . . . . . . 2
8. Flat Washer . . . . . . . . . . . . . . 13
9. Short Screws . . . . . . . . . . . . . . 3
10. Long Screws . . . . . . . . . . . . 10
11. Back Support (Pre-Installed) . 1
12. Allen Wrench (Not Shown) . . 1
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert five Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place.
Insert Pneumatic Cylinder (3) into Base (1).
STEP 2 Attach Mechanism (4) to Seat Cushion (5) with the arrow pointing towards the front of the chair, using four Flat Washers (8), and Four
Long Screws (10). TIGHTEN ALL SCREWS COMPLETELY USING ALLEN WRENCH (12).
STEP 3 Attach Back Support (11) to Mechanism (4) using three Flat Washers (8), and three Short Screws (9),
FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (12).
STEP 4 Align the holes in the Arms (7L & 7R) with the holes in the Seat Cushion (5), Attach Arms (7L & 7R) to Seat Cushion (5) using three Flat
Washers (8) and three Long Screws (10) for each arm. FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (12).
STEP 5 Place the assembled seat on top of Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.
DETAIL A
1
2
3
4
5
6
7L
7R
8,10
11
8,10
8,10
9
8
11
5
4
8,10
8,10