Office Star Products WD5330/WD5670 User manual

1
2
FEATURE
• HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever
(1). To lower seat height sit on chair and lift lever (1).
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped
with an adjustment that will allow the user to change the
tension of the tilting feature. Turn knob (2) clockwise
to increase tension and counter-clockwise to decrease
or ease the tension. To lock return chair to the upright
position and push lever (1) in. To unlock pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob
completely.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts, screws, and knobs
are securely tightened.
3. Check that all bolts, screws, and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
WD5330/WD5670 LEATHER & WOOD EXECUTIVE CHAIR
OPERATING INSTRUCTIONS
WARRANTY
Work Smart chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on up upholstery fabric and foam against wear and deterioration.
• We cannot warrant leather against routine scratching and scuffing, as all leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number and description of the problem and obtain return
authorization. At it’s option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component. The customer must prepay freight on any components returned to the factory. Return freight
on components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products.The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric and foam is warranted for one year.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
All Work Smart chairs are built to meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m.
Pacific Time.

PART QTY
1.Base.....................1
2.Casters ..................5
3. Pneumatic Cylinder . . . . . . . . . 1
4.Bellows ..................1
5.SeatPlate ................1
6. Seat Cushion . . . . . . . . . . . . . . 1
7. Back Cushion. . . . . . . . . . . . . . 1
8. Long Screws . . . . . . . . . . . . . . 6
9. Short Screws . . . . . . . . . . . . . . 8
10. Arms Left (10L) Right (10R) . 2
11.Caps ...................6
12. Back Support (pre-installed) . 1
13. Allen Wrench (not shown) . . . 1
14. Socket Wrench (not shown). . 1
1
3
4
9
10L
10R
6
9
9
7
DETAIL A:
Assemble the back support over the
seat plate
12
9
Before You Begin: Open, identify and count all parts prior to assembly. Lay out the parts on
a non-abrasive surface such as a carpet or blanket.
STEP 1 Insert five Casters (2) into Base (1). Insert Pneumatic Cylinder (3) into Base (1) and slip
Bellows (4) over cylinder shaft.
STEP 2 Attach Seat Plate (5) to Seat Cushion (6) with the arrow towards the front of the chair
using four Short Screws (9).
TIGHTEN ALL FOUR SCREWS COMPLETELY
STEP 3 Attach Back Support (12) to Seat Cushion (6) using four Short Screws (9). DO NOT FULLY TIGHTEN SCREWS. IMPORTANT NOTE:
MAKE SURE YOU HAVE ASSEMBLED THE BACK SUPPORT PLATE (12) OVER THE SEAT PLATE (5) THAT YOU ATTACHED
TO THE SEAT CUSHION IN STEP 2. (SEE DETAIL A)
STEP 4 Align the holes in the Arms (10L and 10R) with the holes in the Seat Cushion (6) and Back Cushion (7). Attach Arms (10L and 10R) to Seat
Cushion (6) and Back Cushion (7) using six Long Screws (8). FULLY TIGHTEN ALL SCREWS.
STEP 5 Cover the screws on the arms with six caps (11).
STEP 6 Place the assembled seat on top of Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.
2
5
8,11
8,11
WD5330/WD5670 LEATHER & WOOD EXECUTIVE CHAIR
ASSEMBLY INSTRUCTIONS
9
12
© Office Star Products May 2006