Office Star Work Smart DH89675 User manual

DH89675 / FL89675
MANAGER’S CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and press
lever (1). To lower seat height sit on chair and
press lever (1).
NOTE: It is normal for chair to slightly lower under
body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with
an adjustment that will allow the user to change the tension
of the tilting feature. Turn knob (2) clockwise to increase
tension and counter-clockwise to decrease or ease the
tension. To lock return chair to the upright position and push
lever (1) in. To unlock pull lever (1) out.
NOTE: Be careful not to loosen the back tilt adjustment knob
completely.
• ARM FLIP UP AND DOWN
To flip arms up, simply pull up on arm. To lower arm, simply
pull down on arm.
12
LIMITED WARRAnTy
Work Smart chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and
obtain return authorization. At it’s option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component. The customer must prepay freight on any components returned to the factory. Return
freight on components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric and foam is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00
p.m. Pacific Time.
WARnInG
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing
tension.
5. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
FL89675
(not shown)

DH89675 / FL89675
MANAGER’S CHAIR
ASSEMBLY INSTRUCTIONS
© Office Star Products January 2012
1
2
3
4
5
8
9
6
10
7L
7R
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert five Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place. Insert Pneumatic
Cylinder w/ Bellows (3) into Base (1).
STEP 2 Attach Arms (7L & 7R) to Seat Cushion (5) using one Flat Washer (8) and one Medium Screw (10) for inner hole, two Flat
Washers (8) and two Long Screws (11) for outer holes. FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (13).
STEP 3 Attach Seat Plate (4) to Seat Cushion (5) with the arrow towards the front of the chair, using two Flat Washers (8), two Medium
Screws (10) for front holes and two Flat Washers (8) and two Short Screws (9) for rear holes. FULLY TIGHTEN ALL SCREWS USING
ALLEN WRENCH (13).
STEP 4 Attach Back Support (12) to Seat Cushion (5) using four Flat Washers (8) and four Short Screws (9). FULLY TIGHTEN ALL SCREWS
USING ALLEN WRENCH (13).
STEP 5 Place the assembled seat on top of Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.
PA R T QTY
1. Base .......................1
2. Casters .....................5
3. Pneumatic Cylinder w/ Bellows ...1
4. Seat Plate ...................1
5. Seat Cushion .................1
6. Back Cushion ................1
7. Arms (7R & 7L) ...............2
8. Flat Washers ................14
9. Short Screws .................6
10. Medium Screws ..............4
11. Long Screws ................4
12. Back Support (pre-installed) ....1
13. Allen Wrench (not shown) ......1
11
12
8
8
8
8
10
9