Officine Gullo PVS4EM User manual

x
INSTRUCTIONS
for installation and use
ELECTRICAL GLASS CERAMIC COOKING TOP FOR
RESIDENTIAL AND PROFESSIONAL USE
PVS4EM

2Ofcine Gullo

3
Ofcine Gullo
TABLE OF CONTENTS
WARNINGS & CAUTION............................................................................2
SAFETY INSTRUCTIONS .........................................................................3
ELECTRICAL SCHEME ............................................................................6
INSTALLATION INTRUCTIONS.................................................................7
USE AND MAINTENANCE INSTRUCTIONS............................................9
CLEANING AND CARE INSTRUCTIONS................................................10

4Ofcine Gullo
WARNINGS & CAUTION
1. Before using the appliance, read the instruction manual carefully, as it contains important safety infor-
mation on the proper installation, use and maintenance of the appliance. Please keep the instruction
manual for further reference.
2. The appliance’s electrical safety is guaranteed only if the electrical system is grounded in accordance
with the relevant regulations. It is of the utmost importance to follow such regulations; when in doubt,
please consult a qualied electrician to have the electrical system thoroughly checked. The manufac-
turer declines all responsibility for damage caused by a improperly grounded electrical system
3. Before connecting the appliance, make sure that the appliance’s technical characteristics shown on
the tag correspond to those of the electrical system supply.
4. Make sure that the electrical system and sockets can handle the appliance’s maximum power con-
sumption as shown on the tag. When in doubt, please consult a qualied electrician.
5. When not in use for extended periods, switch off the general power supply to the appliance.
6. Do not obstruct the appliance’s cooling or heat dissipation vents.
7. The appliance must be used only for the purposes for which it has been expressly designed (cooking).
All other uses (such as the heating of a room) are considered inappropriate and therefore dangerous.
The manufacturer declines all responsibility for damage resulting from improper use of the appliance.
8. The use of any electric appliance implies the observance of some basic rules. More specically:
- Avoid the use of extension cords and, if necessary, take all precautions;
- Do not pull the power cord to disconnect the plug from the power socket;
- Do not allow children or untrained persons to use the appliance.
9. Before performing maintenance work, disconnect the appliance by pulling the plug out of the power
socket or turning off the main switch.
10. In case of failure or malfunction, turn the appliance off and do not attempt to carry out any repairs,
which must be done exclusively by an authorized service center.

5
Ofcine Gullo
SAFETY INSTRUCTIONS
Do not store or use gasoline or other ammable vapors or liquids in the vicinity of this or
any other appliance.
WARNING: Improper installation, adjustment,alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this equipment.
To avoid personal injury or property damage, please read and follow these important safety
precautions.
1. Before any maintenance or repairs are performed, disconnect the appliance from the
electric supply.
2. Your appliance should be installed by a qualied installation technician. Have the technician
show you the exact location of the electric supply so you know how to turn off the apliance.
3. On positioning the appliance, ensure that it is perfectly levelled
4. Do not attempt to repair or replace any part of this appliance unless specically instructed
to do so by this manual. In-warranty service must be performed by an authorized service
agency.
5. If the appliance is placed near a wall or partition, kitchen furniture or decorative coverings,
etc., these must be re-proof or coated with re-proong.
6. Children should not be left alone or unattended in the kitchen while the appliance is in use.
7. It is advisable to place the oven under an extractor hood to ensure rapid elimination of
steam.
8. The ventilation and ue ways of this appliance must remain unobstructed at all times.
9. Do not store items of interest to children above the appliance. Children, as well as adults,
should never be allowed to sit, stand, or climb on any part of the appliance. Serious injury
may occur.
10. Never leave the appliance unattended during use.
11. For your safety, never use your appliance or any other cooking appliance as a space
heater to warm or heat the room.
14. Use only dry potholders. Moist or damp potholders on hot surfaces may result in steam
burns.
15. For a correct installation do not overlap induction elements.

6Ofcine Gullo
25
SCHEMA ELETTRICO – SCHALTPLAN – SCHEMA ELECTRIQUE
WIRING DIAGRAM – ESQUEMA ELECTRICO
PCC-74ET, PCCT-74ET
549005502 M00_01
230Vac3 50/50Hz 400Vac2N 50/60Hz
1
Morsettiera Klemm-leiste Bornier Junction-box Tablero de bornes
2
Piastra Kochplatte Plaque Hotplate Placa
3
Regolatore di energia Energie regler Regolateur de energie Energy regulator Regolador de energia
4
Spia bianca weiße Kontroll-Leuchte Témoin blanc White light Luz indicadora blanca
5 Lampada spia calore
residuo
Kontrolleuchte für
Restwärme
Lampe témoin de chaleur
résiduelle
Remaining heat pilot
light Piloto calor residuo
1. Junction-box
2. Hotplate
3. Energy regulator
4. White light
5. Remaining heat pilot
ELECTRICAL SCHEME
The installation of this appliance must conform with all applicable local codes.
In the absence of local codes, the installation must conform to the latest level of the
National Electric Code, ANSI/NFPA 70.
If the electrical supply is not turned on or is interrupted the appliance will not operate.
The applicable wiring diagram for this appliance is below. The circuit where you wire your
appliance to must be grounded and polarized. We recommend the circuit for your appliance
be a non-GCFI dedicated line.

7
Ofcine Gullo
INSTALLATION INSTRUCTIONS
This appliance is Manufactured by OFFICINE GULLO S.r.l
Headquarters and factory
50012 Antella - Bagno a Ripoli (FI) Italy
via della Torricella, 29, - Tel. +39 055
6560324
In the US call (800)-781-7125
Home page http:// www.ofcinegullousa.com
E-Mail: info@ofcinegullousa.com
The manufacturer declines any responsibility for direct or indirect damage caused by
improper or incorrect installation, alterations, maintenance or use of the appliance, as in all
the other cases considered in the items of our sales conditions.
BEFORE YOU BEGIN
The manufacturer declines all responsibility in the event of failure to observe the instructions
given here for installation, maintenance and suitable operation of the product. The
manufacturer further declines all responsibility for injury due to negligence and the warranty
of the unit automatically expires due to improper maintenance and/or installation.
BEFORE YOU BEGIN: It is advisable to test run the oven before installation.
BEFORE STARTING please read this entire document and ensure you are fully conversant
with the require-ments and limitations.
ELECTRICAL INSTALLATION
WARNING: All electrical work must be performed by a qualied electrician.
Please ensure that the appropriate electrical codes or prevailing local building codes and
ordinances are adhered to.
Ensure that the electricity supply is disconnected at source. Do not use an extension cord
or adapter plug with this appliance.
This appliance must be grounded. Connect to a properly grounded branch circuit, protected
by a 15 amp circuit breaker.
Electrical Supply.
This appliance requires electrical supply – ensure an appropriately qualied person
completes the electrical oven-up. The connection point for the electrical supply is at the
top of the unit, therefore the electrical supply must be run down from the ceiling alongside
the ductwork.
All electrical and venting oven-ups must be in place before commencing installation of the
oven.
The appliance must be connected to an equipotential system. The connection screw is
positioned at the back of the appliance and is identied by the symbol .

8Ofcine Gullo
Attention! the manufacturer cannot be held responsible for, and does not cover in the
guarantee any damage resulting from bad or faulty connections.
The appliance is supplied without the connection cable; to install it, proceed in the following
way:
-Remove the back panel bye removing the screws that are around its perimeter as shown
in picture 1E
-Fit the connection cable through the cable channel, connect the conductor wires to the
corresponding terminals in the junction box as shown in picture 2E below and x them into
place.
-Block the cable with the cable blocker, and reassemble the panel. The ground wire must
be longer than the others so that if the cable blocker should break for any reason, it will
disconnect after the hot wires.
N.B. The connection cable must have the following characteristics: it must be type H05RN-F
and must have an adequate section for the power of the appliance (see technical data table).
The installation of this appliance must conform with all applicable local codes.
In the absence of local codes, the installation must conform to the latest level of the
National Electric Code, ANSI/NFPA 70.
TECHNICAL ELECTRICAL DATA TABLE
MODEL Dimensions
cm Power supply
Power
max
kW
Absorbition
max A
Power
supply
cable
PVS4EM 40 x 70 x 29h 230Vac
50/60Hz 521,74 3 x 2,5 mm²

9
Ofcine Gullo
USE AND MAINTENANCE INSTRUCTIONS
INSTRUCTIONS FOR USE
Attention! The appliance must only be used under surveillance.
STARTING UP
Before using the appliance for the rst frying, it is necessary to clean it carefully, (see paragraph
“cleaning and care”). Check the connection of the appliance and start it up following the
instructions.
INSTRUCTIONS FOR USE
Attention!
• Use the appliance only under surveillance.
• Remember that whilst using glass ceramic tops, the crystal surfaces in the cooking
area, increase the temperature considerably; it is therefore necessary to take this into
consideration and act accordingly.
• It is advisable to use recipients with a at bottom, as recipients with concave or rounded
bottoms increase cooking time and energy consumption.
Indications:
• Each hotplate is connected to an energy regulator (selector), giving the possibility to
choose from 6 different temperatures. For the rst cooking, it is advisable to use the highest
temperatures.
• each hotplate is provided with a temperature limiter which comes into function when the
temperature reached may damage the crystal.
• When the crystal surface heats up, the residuous heat light comes on, corresponding to
the hotplate in function. This indicator does not go off until the crystal maintains a high
temperature, even with the hotplate turned off so as to avoid danger of burns.
Warnings:
• Do not use pans or any recipient with the bottom in aluminium or with a tin coating.
• Do not use terracotta pots as they could break or crack and therefore become unhygienic.
It is advisable to use stainless steel pans with a smooth, at bottom and with an adequate
diameter for the heating area. If cast-iron pans are used, be careful not to slide them on the
crystal, in order to avoid any scratches. Make sure that the bottom of the pans has been
dried well before placing them on the top; avoid banging the crystal, especially with sharp
or pointed objects.
• Pay attention never to cover the crystal with sheets of aluminium paper or anything similar,
during use.Never start up the appliance without oil.
Any kind of food (meat, sh, legumes, eggs, rice, vegetables, etc.) can be cooked on the glass
ceramic coking tops, providing suitable pans are used..

10 Ofcine Gullo
TURNING ON
Switch on the main switch installed above the appliance. Turn the control knob corresponding
to the hotplate from position “0” to the degree of heating desired, between 1 and 6. The light
comes on, as son as the power supply is on.
The green light indicates the presence of electrical tension. To turn off the hotplate, turn the
knob back into position “0”. The hotplates are made up of a nucleus and a crown.
Turning the knob, as indicated above, only the nucleus of the hotplate comes on; turning the
knob beyond position “6”, the crown also comes on and the temperature can, once again be
regulated from pos. “1” to pos. “6”.
CARE AND CLEANING INSTRUCTIONS
Attention! During cleaning, do not wash the external parts of the appliance with direct
sprays of water or with high pressure.
After every use, clean the appliance thoroughly. Daily cleaning after switching off the
appliance ensures the perfect functioning and long life of the appliance.
Before starting to clean the appliance, disconnect the power supply. The parts in steel must
be washed with hot water and neutral detergent, then rinsed thoroughly in order to eliminate
all traces of detergent; after which, dried with a dry cloth. Do not use abrasive or corrosive
detergents.
Cleaning the crystal
The crystal must be cleaned with degreasing liquids, acids containing vinegar and lemon,
suitable for cleaning ceramic and crystal. It is advisable to carry out this operation when
the crystal is not completely cold, so that spilled food, burned grease, etc. can be softened
using a damp cloth and removed whilst still warm with an ordinary scraper, in order to avoid
damaging the crystal surface.
Do not use abrasive or corrosive detergents.
Important: As well as ordinary cleaning and maintenance, it is advisable to have the installation
checked by an installer at least once a year.
It is therefore suggested to draw up an after-sales assistance contract.
CLEANING BURNISHED BRASS SURFACES
No synthetic protective varnishes have been used to obtain the special burnishing effect on
the burnished brass details in order to avoid spoiling the beauty of the brass with an articial
patina. The antique nish of the surface is the result of natural oxidation that has simply
been accelerated. All the natural antique nish brass surfaces can be cleaned with mild
soap and warm water, accompanied by the use of an abrasive pad (the green color type
used for washing dishes). It is recommended that the metal be rubbed, uniformly applying
light pressure, use caution as this will remove some of the patina if rubbed excessvily.
The brass details should then be dried.

11
Ofcine Gullo
Do not use metal polish as this is suitable not to clean the antique nish and could result in
loos of the color and patina. Oxidation that may appear over time on the burnished brass
surfaces is a normal characteristic of our craft metal working processes.
CLEANING CHROME PLATED BRASS SURFACES
No synthetic varnishes have been used to obtain the special polish on the chromium-plated
brass details in order to avoid spoiling the beauty of the chrome with an articial patina. All
the chromed surfaces should be clean as needed with a warm water and mild soap and a
soft cloth or micro-ber. Do not use abrasive pads.
CLEANING SATIN FINISH NICKEL PLATED BRASS SURFACES
No synthetic varnishes have been used to obtain the special nickel-plating on the satin
nish nickel-plated brass details in order to avoid spoiling the beauty of the nickel-plated,
satin nished solid brass with an articial patina. All the nickel-plated and satin nished
brass surfaces should be cleaned, where necessary, with a soft cloth or micro-ber cloth,
combined with a neutral detergent, if required. Do not use abrasive pads.
CLEANING THE VARNISHED SURFACES
All the varnished surfaces should be cleaned using a neutral detergent and, where necessary,
a soft cloth or micro-ber cloth. Do not use abrasive pads or any other chemical products.
CLEANING BRUSHED STEEL SURFACES
All the brushed steel surfaces should be cleaned using degreasing products or products
specically designed to be used on steel and, where necessary, extra-ne steel wool.
WHAT TO DO IN THE EVENT OF A BREAKDOWN
In the event of breakdown, turn off the appliance, disconnect the power supply and notify
your authorized service center or call our main line at [phone]

WWW.OFFICINEGULLO.COM
V 2.3 - 10.17
OFFICINE GULLO S.R.L.: via della Torricella 29, 50012 Antella - Bagno a Ripoli (FI)
Tel. [phone] / 621807 - Fax: + 39 055 620670 - [email protected]
us