Okayo OMG-100T Plus User manual

OMG-100T/R
[User manual]
All-around Guiding System

Transmitter OMG-100T………………………………………………………….…………….......….………….….........1
C
Illustration
O
Device Installation
C
Device Installation
Index
Transmitter OMG-100T.......................................................................................................1
Receiver OMG-100R ...........................................................................................................1
Mode Comparison Table .....................................................................................................1
Live tour…………………………………………………………………………………….…….….................................2-3
Po wer On
Assign Your Group Channel
Change Your Channel
Talk to Your Group Members
Adjust Your Talk Setting and Mic. Level
Adjust Your Volume
Power Off
Information Page
Setting Check
Illustration
Application & Operation
Audio tour……………………………………………………………………………….……….….................................4-5
Guided audio tour ……………..…………….……………….….............................................................6-8
Power On
Change Your Mode to Player (OMG-100T)
Change Your Mode to Player (OMG-100R)
Select Your Language (1-32)
Change Your Language (1-32)
Listen to Your Audio Track (1-9,999)
Adjust Your Volume
Power Off
Information Page
Setting Check
Power On
Change Your Mode to Guide (OMG-100T)
Change Your Mode to Listen (OMG-100R)
Assign Your Group Channel
Change Your Channel
Talk to Your Group Members
Adjust Your Talk Setting and Mic. Level
Send Your Track Content to Group Members
Select Your Language (1-32)
Change Your Language (1-32)
Adjust Your Volume
Power Off
Information Page
Setting Check
Terms OMG-100T and OMG-100R will be expressed for OMG-100T and OMG-100R
in the manual.

Index
Multilingual audio tour…………………………………………………….................................................9-11
Power On
Change Your Mode to Leader (OMG-100T)
Change Your Mode to Guest (OMG-100R)
Assign Your Group Channel
Change Your Channel
Talk to Your Group Members
Adjust Your Talk Setting and Mic. Level
Assign Your Track Command to Group Members
Select Your Language (1-32)
Change Your Language (1-32)
Adjust Your Volume
Power Off
Information Page
Setting Check
OMG-100T can't hear his own voice……………………………………………….…………………………..………….17
O MG-100R can't hear OMG-100T………………………………………………..………………………….…….……….17
N o track in the folder…………………………………………………………………….………………………………..….….17
U nknown track…………………….……………………………………………………………………………………….…….….17
S D ERROR…………………………………………………………………………….……………………………………….…….….17
F ailed communication…………………………………………………..……………………..…..………………...…….….17
L ow battery…………………………………………………..………………………………..…………………………….….……17
Alarm…………………………………………………..………………………………..…………………………………….…….....17
Charging via uploading cable………………..………………………………..…………………………………….…......17
Troubleshooting
Specification…………………………………………………….....................................................................18
2 Speakers (Duo-speaker lecturing)……………………………………............................................12-14
2 Speakers (Team discussion)…………………………………….....................................................15-16
Power On
Change Your Mode to Lecture(M) or Lecture(S) (OMG-100T)
Change Your Mode to Listen (OMG-100R)
Assign Your Group Channel
Change Your Channel
Talk to Your Participants
Adjust Your Talk Setting and Mic. Level
Send Your Track Content to Participants
Select Your Language (1-32)
Change Your Language (1-32)
Adjust Your Volume
Power Off
Information Page
Setting Check
Power On
Change Your Mode to Lecture(M) or Lecture(S)
Change Your Channel
Talk to Your Group Members
Adjust Your Talk Setting and Mic. Level
Select Your Language (1-32)
Change Your Language (1-32)
Adjust Your Volume
Power Off
Information Page
Setting Check

1
O
Transmitter OMG-100T
Receiver OMG-100R
Device Installation
C
Illustration
2
3
1
4
6
7
5
9
11
10
13
10
12
9
8
*Users with hearing assistive devices can directly
listen to speaker.
1. Infrared sensor
2. Antenna
3. Charging/Talk/RF LED indicator
4. Hearing aid compatible (HAC*) speaker
5. TALK button
6. Backlit LCD screen
7. Soft-touch keypad
8. Inbuilt microphone
9. Charging/Uploading connector
10. Headphone jack, 3.5 mm
11. Microphone jack, 3.5 mm
12. Reset key
13. Lanyard hole
*Default mode of players is set beforehand.
4
5
6
7
8
2
3
1
*Users with hearing assistive devices can directly
listen to speaker.
1. Infrared sensor
2. Antenna
3. Charging/RF LED indicator
4. Hearing aid compatible (HAC*) speaker
5. Backlit LCD screen
6. Soft-touch keypad
7. Charging/Uploading connector
8. Headphone jacks, 3.5 mm
9. Reset key
10. Lanyard hole
Mode Comparison Table
OMG-100T
OMG-100R
Mode1 Mode2 Mode3 Mode4 Mode5 Mode6
Player
Player
Guide
Guest
Leader Live* Lecture(M) Lecture(S)
Listen*
OMG-100T l OMG-100R
- - -

Assign Your Group Channel
1. Turn OMG-100T and OMG-100R on.
2. Type in # and then press the button on both OMG-100T and OMG-100R.
3. Last selected channel number flashes slowly on OMG-100T whereas it flashes quickly on
OMG-100R.
4. Press the or button to select a new channel on OMG-100T, if necessary. No channel
adjustment is available on OMG-100R at this step.
5. Press the button to confirm new channel, which starts to flash quickly on OMG-100T.
6. OMG-100T is now sending signal of new-channel assignment to OMG-100R.
7. When OMG-100R receives new-channel assignment, new channel number shows up and
stops flashing. OMG-100R leaves the setting afterwards.
8. If OMG-100R fails to receive new-channel assignment, last selected channel number keeps
flashing quickly on the screen until the button is pressed to leave the setting.
9. To release OMG-100T from the setting, press the button at any time.
There is no turn-on sequence between OMG-100T and OMG-100R for channel assignment.
2
Power On
Change Your Channel (if necessary)
1. Press the button for 1 second to turn the player on.
1. OMG-100T and OMG-100R are automatically channel locked when they are turned on.
2. Press both and buttons simultaneously till symbol disappears. Last selected
channel starts to flash on the screen.
3. Press the or button to change your channel.
4. Press the button or leave it for 5 seconds to confirm newly selected channel.
5. Selected channel stops flashing. OMG-100T and OMG-100R leave the setting automatically.
2. If shows up, press both and buttons simultaneously for 1 second to turn the
player on.
Live tour
The group guide talks to group members.
Application & Operation
OMG-100T (group guide)
OMG-100R
Mode
(group member)
Live
Listen
+
Turn On
Players are with inbuilt battery and make sure their batteries are fully charged before being
operated.
OMG-100T l OMG-100R

3
Talk to Your Group Members (OMG-100T)
Adjust Your Talk Setting and Mic. Level (if necessary) (OMG-100T)
Power Off
1. The group guide can talk to group members via a press of Talk button .
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
1. To turn the player off, either press the button for 10 seconds or place it into chargers.
Anti-theft system is still on.
2. Three Talk preferences are available:
a) PTB: push to bolt
b) PTM: push to mute
c) PTT(default): push to talk
2. Default mode Live shows up. Press the button to continue.
2. To turn the player and its anti-theft system off, press both and buttons simultaneously
for 3 seconds or place it into uploaders.
3. Default talk PTT shows up. Press the or button to change your Talk preference.
4. Press the button to confirm (underline) the selection and then enter next setting.
5. Default mic. level Mid shows up. Press the or button to change your Mic. Level.
6. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
5
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and
buttons should be pressed at the same time at this step.
Adjust Your Volume
Information Page
Setting Check
1. Press the or button to adjust the volume when OMG-100R is on.
2. When preferred volume is set, leave it for 1 second and OMG-100R will leave the setting
automatically.
There are 11 volume levels in total and default volume is at level 6. When level 0 is set, the
player will be muted.
Kindly note listening at high volume for long periods may damage your hearing.
1. Press the button when the player is on.
2. Above screen shows up.
3. Create your own page via Audio Master 3, if needed.
1. To check the player setting, press both and buttons* simultaneously when the player is off.
2. Above screen shows up. Press the button to turn the page. or
3. To leave this screen, press the button and the player will be off again.
* If the player was turned off by pressing both and buttons simultaneously earlier, , and
buttons should be pressed at the same time at this step.
OMG-100T l OMG-100R

4
Power On
Change Your Mode to Player (OMG-100T)
Change Your Mode to Player (OMG-100R)
Select Your Language (1~32)
Change Your Language (1~32)(if necessary)
1. Press the button for 1 second to turn the player on.
1. Every time when the player is turned on, language screen shows up.
2. Press the or button to select your language.
3. Press the button to confirm selected language and leave the setting.
1. If you intend to change the language when the player is on, type in #1, and then press the
button.
2. Press the or button to select your language.
3. Press the button again to confirm selected language and leave the setting.
2. If shows up, press both and buttons simultaneously for 1 second to turn the
player on.
Audio-tour
An audio player only.
OMG-100T (visitor)
(visitor)
OMG-100R
Mode
Player
Player
+
Turn On
Players are with inbuilt battery and make sure their batteries are fully charged before being
operated.
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Default mode Live shows up. Press the or button to change your mode to Player.
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100R is off.
2. Default mode Listen shows up. Press the or button to change your mode to Player.
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100R
will be off again.
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
*If OMG-100R was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
OMG-100T l OMG-100R

5
Listen to Your Audio Track (1~9,999)
Power Off
1. Type in preferred track number when the player is on.
2. Press the button if you would like to change to a new number.
3. Press the button to play the track.
4. Keep pressing the or button to fast forward or backward the track.
5. Press the button again to pause the track, if needed.
6. Press the button to stop the track, if needed.
1. To turn the player off, either press the button for 10 seconds or place it into chargers.
Anti-theft system is still on.
2. To turn the player and its anti-theft system off, press both and buttons simultaneously
for 3 seconds or place it into uploaders.
Adjust Your Volume
Information Page
Setting Check
1. Press the or button to adjust the volume when the player is on.
2. When preferred volume is set, leave it for 1 second and the player will leave the setting
automatically.
There are 11 volume levels in total and default volume is at level 6. When level 0 is set, the
player will be muted.
Kindly note listening at high volume for long periods may damage your hearing.
1. Press the button when the player is on.
2. Above screen shows up.
3. Create your own page via Audio Master 3, if needed.
1. To check the player setting, press both and buttons* simultaneously when the player is off.
2. Above screen shows up. Press the button to turn the page. or
3. To leave this screen, press the button and the player will be off again.
* If the player was turned off by pressing both and buttons simultaneously earlier, , and
buttons should be pressed at the same time at this step.
The track will be played automatically without a press of button when “auto-play”
function is enabled via Audio Master 3.
OMG-100T l OMG-100R

6
O
Device Installation
C
Power On
1. Press the button for 1 second to turn the player on.
2. If shows up, press both and buttons simultaneously for 1 second to turn the
player on.
Guided audio tour
The group guide can not only talk to but also send
track content to group members.
OMG-100T (group guide)
OMG-100R
Mode
(group member)
Guide
Listen
+
Turn On
Players are with inbuilt battery and make sure their batteries are fully charged before being
operated.
Device Installation
Change Your Mode to Guide (OMG-100T)
Change Your Mode to Listen (OMG-100R)
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Default mode Live shows up. Press the or button to change your mode to Guide.
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100R is off.
2. Default mode Listen shows up. Press the or button to change your mode to Listen.
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100R
will be off again.
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
*If OMG-100R was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
Assign Your Group Channel
1. Turn OMG-100T and OMG-100R on.
2. Type in # and then press the button on both OMG-100T and OMG-100R.
3. Last selected channel number flashes slowly on OMG-100T whereas it flashes quickly on
OMG-100R.
4. Press the or button to select a new channel on OMG-100T, if necessary. No channel
adjustment is available on OMG-100R at this step.
5. Press the button to confirm new channel, which starts to flash quickly on OMG-100T.
6. OMG-100T is now sending signal of new-channel assignment to OMG-100R.
7. When OMG-100R receives new-channel assignment, new channel number shows up and
stops flashing. OMG-100R leaves the setting afterwards.
OMG-100T l OMG-100R

8. If OMG-100R fails to receive new-channel assignment, last selected channel number keeps
flashing quickly on the screen until the button is pressed to leave the setting.
9. To release OMG-100T from the setting, press the button at any time.
There is no turn-on sequence between OMG-100T and OMG-100R for channel assignment.
Change Your Channel (if necessary)
Send Your Track Content to Group Members (OMG-100T)
1. OMG-100T and OMG-100R are automatically channel locked when they are turned on.
1. Type in preferred track number on OMG-100T.
2. Press both and buttons simultaneously till symbol disappears. Last selected
channel starts to flash on the screen.
3. OMG-100R plays the track sent from OMG-100T.
4. This track will be paused if Talk function is enabled on OMG-100T.
3. Press the or button to change your channel.
4. Press the button or leave it for 5 seconds to confirm newly selected channel.
5. Selected channel stops flashing. OMG-100T and OMG-100R leave the setting automatically.
2. Press the button on OMG-100T to play and send the track content to OMG-100R.
Talk to Your Group Members (OMG-100T)
Adjust Your Talk Setting and Mic. Level (if necessary) (OMG-100T)
1. The group guide can talk to group members via a press of Talk button .
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Three Talk preferences are available:
a) PTB: push to bolt
b) PTM: push to mute
c) PTT(default): push to talk
2. Default mode Guide shows up. Press the button to continue.
3. Default talk PTT shows up. Press the or button to change your Talk preference.
4. Press the button to confirm (underline) the selection and then enter next setting.
5. Default mic. level Mid shows up. Press the or button to change your Mic. Level.
6. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
5
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and
buttons should be pressed at the same time at this step.
The track being played on OMG-100R can't be stopped if the button is pressed on
OMG-100R.
Select Your Language (1~32) (OMG-100T)
1. Every time when the player is turned on, language screen shows up.
2. Press the or button to select your language.
3. Press the button to confirm selected language and leave the setting.
7
OMG-100T l OMG-100R

8
Change Your Language (1~32)(if necessary) (OMG-100T)
1. If you intend to change the language when the player is on, type in #1, and then press the
button.
2. Press the or button to select your language.
3. Press the button again to confirm selected language and leave the setting.
Power Off
1. To turn the player off, either press the button for 10 seconds or place it into chargers.
Anti-theft system is still on.
2. To turn the player and its anti-theft system off, press both and buttons simultaneously
for 3 seconds or place it into uploaders.
Adjust Your Volume
Information Page
Setting Check
1. Press the or button to adjust the volume when the player is on.
2. When preferred volume is set, leave it for 1 second and the player will leave the setting
automatically.
There are 11 volume levels in total and default volume is at level 6. When level 0 is set, the
player will be muted.
Kindly note listening at high volume for long periods may damage your hearing.
1. Press the button when the player is on.
2. Above screen shows up.
3. Create your own page via Audio Master 3, if needed.
1. To check the player setting, press both and buttons* simultaneously when the player is off.
2. Above screen shows up. Press the button to turn the page. or
3. To leave this screen, press the button and the player will be off again.
* If the player was turned off by pressing both and buttons simultaneously earlier, , and
buttons should be pressed at the same time at this step.
OMG-100T l OMG-100R

9
Power On
1. Press the button for 1 second to turn the player on.
2. If shows up, press both and buttons simultaneously for 1 second to turn the
player on.
Multilingual audio tour
The group guide can not only talk to but also assign
audio command to group members who are having
the players with respective languages.
OMG-100T (group guide)
OMG-100R
Mode
(group member)
Leader
Guest
+
Turn On
Players are with inbuilt battery and make sure their batteries are fully charged before being
operated.
Change Your Mode to Leader (OMG-100T)
Change Your Mode to Guest (OMG-100R)
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Default mode Live shows up. Press the or button to change your mode to Leader.
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100R is off.
2. Default mode Listen shows up. Press the or button to change your mode to Guest.
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100R
will be off again.
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
*If OMG-100R was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
Assign Your Group Channel
1. Turn OMG-100T and OMG-100R on.
2. Type in # and then press the button on both OMG-100T and OMG-100R.
3. Last selected channel number flashes slowly on OMG-100T whereas it flashes quickly on
OMG-100R.
4. Press the or button to select a new channel on OMG-100T, if necessary. No channel
adjustment is available on OMG-100R at this step.
5. Press the button to confirm new channel, which starts to flash quickly on OMG-100T.
6. OMG-100T is now sending signal of new-channel assignment to OMG-100R.
7. When OMG-100R receives new-channel assignment, new channel number shows up and
stops flashing. OMG-100R leaves the setting afterwards.
OMG-100T l OMG-100R

10
8. If OMG-100R fails to receive new-channel assignment, last selected channel number keeps
flashing quickly on the screen until the button is pressed to leave the setting.
9. To release OMG-100T from the setting, press the button at any time.
There is no turn-on sequence between OMG-100T and OMG-100R for channel assignment.
Change Your Channel (if necessary)
Assign Your Track Command to Group Members (OMG-100T)
1. OMG-100T and OMG-100R are automatically channel locked when they are turned on.
1. Type in preferred track number on OMG-100T.
2. Press both and buttons simultaneously till symbol disappears. Last selected
channel starts to flash on the screen.
3. OMG-100R starts to play the track assigned by OMG-100T.
4. This track will be paused if Talk function is enabled on OMG-100T.
3. Press the or button to change your channel.
4. Press the button or leave it for 5 seconds to confirm newly selected channel.
5. Selected channel stops flashing. OMG-100T and OMG-100R leave the setting automatically.
2. Press the button on OMG-100T to assign track command to OMG-100R.
Talk to Your Group Members (OMG-100T)
Adjust Your Talk Setting and Mic. Level (if necessary) (OMG-100T)
1. The group guide can talk to group members via a press of Talk button .
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Three Talk preferences are available:
a) PTB: push to bolt
b) PTM: push to mute
c) PTT(default): push to talk
2. Default mode Leader shows up. Press the button to continue.
3. Default talk PTT shows up. Press the or button to change your Talk preference.
4. Press the button to confirm (underline) the selection and then enter next setting.
5. Default mic. level Mid shows up. Press the or button to change your Mic. Level.
6. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
5
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and
buttons should be pressed at the same time at this step.
The track being played on OMG-100R can't be stopped if the button is pressed on
OMG-100T.
Select Your Language (1~32)
1. Every time when the player is turned on, language screen shows up.
2. Press the or button to select your language.
3. Press the button to confirm selected language and leave the setting.
Change Your Language (1~32)(if necessary)
1. If you intend to change the language when the player is on, type in #1, and then press the
button.
2. Press the or button to select your language.
3. Press the button again to confirm selected language and leave the setting.
OMG-100T l OMG-100R

11
Power Off
1. To turn the player off, either press the button for 10 seconds or place it into chargers.
Anti-theft system is still on.
2. To turn the player and its anti-theft system off, press both and buttons simultaneously
for 3 seconds or place it into uploaders.
Adjust Your Volume
Information Page
Setting Check
1. Press the or button to adjust the volume when the player is on.
2. When preferred volume is set, leave it for 1 second and the player will leave the setting
automatically.
There are 11 volume levels in total and default volume is at level 6. When level 0 is set, the
player will be muted.
Kindly note listening at high volume for long periods may damage your hearing.
1. Press the button when the player is on.
2. Above screen shows up.
3. Create your own page via Audio Master 3, if needed.
1. To check the player setting, press both and buttons* simultaneously when the player is off.
2. Above screen shows up. Press the button to turn the page. or
3. To leave this screen, press the button and the player will be off again.
* If the player was turned off by pressing both and buttons simultaneously earlier, , and
buttons should be pressed at the same time at this step.
OMG-100T l OMG-100R

Power On
1. Press the button for 1 second to turn the player on.
2. If shows up, press both and buttons simultaneously for 1 second to turn the
player on.
2 Speakers (Duo-speaker lecturing)
Max. 2 speakers can talk simultaneously in
a seminar/conference/discourse.
+
Turn On
Players are with inbuilt battery and make sure their batteries are fully charged before being
operated.
Change Your Mode to Lecture(M) or Lecture(S) (OMG-100T)
Change Your Mode to Listen (OMG-100R)
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Default mode Live shows up. Press the or button to change your mode to Lecture(M)
or Lecture(S).
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100R is off.
2. Default mode Listen shows up. Press the or button to change your mode to Listen.
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100R
will be off again.
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
*If OMG-100R was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
Assign Your Group Channel
1. Turn OMG-100T and OMG-100R on.
2. Type in # and then press the button on both OMG-100T and OMG-100R.
3. Last selected channel number flashes slowly on OMG-100T whereas it flashes quickly on
OMG-100R.
4. Press the or button to select a new channel on OMG-100T, if necessary. No channel
adjustment is available on OMG-100R at this step.
5. Press the button to confirm new channel, which starts to flash quickly on OMG-100T.
6. OMG-100T is now sending signal of new-channel assignment to OMG-100R.
7. When OMG-100R receives new-channel assignment, new channel number shows up and
stops flashing. OMG-100R leaves the setting afterwards.
OMG-100T l OMG-100R
12
Mode
Lecture(M)
Lecture(S)
Listen
OMG-100T
OMG-100T
(lecturer)
(assistant lecturer)
OMG-100R (participant)

8. If OMG-100R fails to receive new-channel assignment, last selected channel number keeps
flashing quickly on the screen until the button is pressed to leave the setting.
9. To release OMG-100T from the setting, press the button at any time.
There is no turn-on sequence between OMG-100T and OMG-100R for channel assignment.
Change Your Channel (if necessary)
Send Your Track Content to Participants (OMG-100T)
1. OMG-100T and OMG-100R are automatically channel locked when they are turned on.
1. Type in preferred track number on OMG-100T.
2. Press both and buttons simultaneously till symbol disappears. Last selected
channel starts to flash on the screen.
3. OMG-100R hears the track sent from OMG-100T.
4. This track will be paused if Talk function is enabled on OMG-100T.
3. Press the or button to change your channel.
4. Press the button or leave it for 5 seconds to confirm newly selected channel.
5. Selected channel stops flashing. OMG-100T and OMG-100R leave the setting automatically.
2. Press the button on OMG-100T to play and send the track content to OMG-100R.
Talk to Your Participants (OMG-100T)
Adjust Your Talk Setting and Mic. Level (if necessary) (OMG-100T)
1. Both lecturers can talk to participants via a press of Talk button .
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Three Talk preferences are available:
a) PTB: push to bolt
b) PTM: push to mute
c) PTT(default): push to talk
2. Default mode Lecture(M) or Lecture(S) shows up. Press the button to continue.
3. Default talk PTT shows up. Press the or button to change your Talk preference.
4. Press the button to confirm (underline) the selection and then enter next setting.
5. Default mic. level Mid shows up. Press the or button to change your Mic. Level.
6. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
5
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and
buttons should be pressed at the same time at this step.
OMG-100R can't stop the track content sent by OMG-100T if the button is pressed on
OMG-100R.
Select Your Language (1~32) (OMG-100T)
1. Every time when the player is turned on, language screen shows up.
2. Press the or button to select your language.
3. Press the button to confirm selected language and leave the setting.
OMG-100T l OMG-100R
13

Change Your Language (1~32)(if necessary) (OMG-100T)
1. If you intend to change the language when the player is on, type in #1, and then press the
button.
2. Press the or button to select your language.
3. Press the button again to confirm selected language and leave the setting.
Power Off
1. To turn the player off, either press the button for 10 seconds or place it into chargers.
Anti-theft system is still on.
2. To turn the player and its anti-theft system off, press both and buttons simultaneously
for 3 seconds or place it into uploaders.
Adjust Your Volume
Information Page
Setting Check
1. Press the or button to adjust the volume when the player is on.
2. When preferred volume is set, leave it for 1 second and the player will leave the setting
automatically.
There are 11 volume levels in total and default volume is at level 6. When level 0 is set, the
player will be muted.
Kindly note listening at high volume for long periods may damage your hearing.
1. Press the button when the player is on.
2. Above screen shows up.
3. Create your own page via Audio Master 3, if needed.
1. To check the player setting, press both and buttons* simultaneously when the player is off.
2. Above screen shows up. Press the button to turn the page. or
3. To leave this screen, press the button and the player will be off again.
* If the player was turned off by pressing both and buttons simultaneously earlier, , and
buttons should be pressed at the same time at this step.
OMG-100T l OMG-100R
14

OMG-100T
Power On
1. Press the button for 1 second to turn the player on.
2. If shows up, press both and buttons simultaneously for 1 second to turn the
player on.
2 Speakers (Team discussion)
All group members are having OMG-100T.
Max. 2 members can talk simultaneously.
Mode
Lecture(M)
Lecture(S)
+
Turn On
Players are with inbuilt battery and make sure their batteries are fully charged before being
operated.
Change Your Mode to Lecture(M) or Lecture(S)
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Default mode Live shows up. Press the or button to change your mode to Lecture(M)
or Lecture(S).
3. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and buttons
should be pressed at the same time at this step.
OMG-100T l OMG-100R
*No OMG-100R is required at this occasion.
*Lecture(S) will be available only when Lecture(M) exists.
Change Your Channel (if necessary)
1. OMG-100T will be automatically channel locked when they are turned on.
2. Press both and buttons simultaneously till symbol disappears. Last selected
channel starts to flash on the screen.
3. Press the or button to change your channel.
4. Press the button or leave it for 5 seconds to confirm newly selected channel.
5. Selected channel stops flashing and OMG-100T leaves the setting automatically.
Talk to Your Group Members
1. All group members can talk via a press of Talk button .
2. Three Talk preferences are available for the group guide:
a) PTB: push to bolt
b) PTM: push to mute
c) PTT(default): push to talk
5
2. Default Talk preference for group members is PTT (push to talk).
Max. 2 people in the group (the guide is included) can talk simultaneously.
If 3 person intends to talk, symbol will show up on the screen for reminder.
Please wait till 2ⁿ person releases the talk button.
15
(group guide)
OMG-100T (group member)
?
?

Adjust Your Talk Setting and Mic. Level (if necessary)
1. Press both # and buttons* simultaneously for 1 second to turn the player on when
OMG-100T is off.
2. Default mode Lecture(M) or Lecture(S) shows up. Press the button to continue.
3. Default talk PTT shows up. Press the or button to change your Talk preference.
4. Press the button to confirm (underline) the selection and then enter next setting.
5. Default mic. level Mid shows up. Press the or button to change your Mic. Level.
6. Press the button to confirm (underline) the selection and leave the setting. OMG-100T
will be off again.
*If OMG-100T was turned off by pressing both and buttons simultaneously earlier, #, and
buttons should be pressed at the same time at this step.
Select Your Language (1~32)
1. Every time when the player is turned on, language screen shows up.
2. Press the or button to select your language.
3. Press the button to confirm selected language and leave the setting.
OMG-100T l OMG-100R
Change Your Language (1~32)(if necessary)
1. If you intend to change the language when the player is on, type in #1, and then press the
button.
2. Press the or button to select your language.
3. Press the button again to confirm selected language and leave the setting.
Adjust Your Volume
1. Press the or button to adjust the volume when the player is on.
2. When preferred volume is set, leave it for 1 second and the player will leave the setting
automatically.
There are 11 volume levels in total and default volume is at level 6. When level 0 is set, the
player will be muted.
Kindly note listening at high volume for long periods may damage your hearing.
16
Power Off
1. To turn the player off, either press the button for 10 seconds or place it into chargers.
Anti-theft system is still on.
2. To turn the player and its anti-theft system off, press both and buttons simultaneously
for 3 seconds or place it into uploaders.
Information Page
Setting Check
1. Press the button when the player is on.
2. Above screen shows up.
3. Create your own page via Audio Master 3, if needed.
1. To check the player setting, press both and buttons* simultaneously when the player is off.
2. Above screen shows up. Press the button to turn the page. or
3. To leave this screen, press the button and the player will be off again.
* If the player was turned off by pressing both and buttons simultaneously earlier, , and
buttons should be pressed at the same time at this step.

17
6
O
OMG-100T can't hear his own voice.
OMG-100R can't hear OMG-100T
Device Installation
C
Trouble Shooting
Make sure the headphone and the microphone are plugged correctly in the player.
Make sure TALK mode is set preferably.
If above solutions can't solve the problem, return the player to your supplier.
Make sure selected channel on both OMG-100T and OMG-100R is same.
Make sure OMG-100R is in the operation range of OMG-100T.
Interference might potentially happen. Being away from other tours and return to yours.
If above solutions can't solve the problem, return the player to your supplier.
There is no track in the folder.
The track does not exist.
An error happens to SD card in the player. Restart the player or press reset key on the
back side.
If this error still exists, return the player to your supplier.
The wireless communication fails if “- -“ shows up. Return the player to your supplier.
The battery is running low. Return the player to the counter for recharging immediately.
Alarm will also be activated when this screen shows up. Return the player to the counter for
alarm release.
To mute the player temporarily (alarm screen is still on), press both and buttons
simultaneously.
Alarm can be released via Loop Controller LT-200+ or chargers/uploaders.
OMG-100T l OMG-100R
To charge the player via an uploading cable directly, press # button after it's been connected
with PC. When symbol shows up on the screen, the player is being charged now.