Oki SHT-7540DN Quick start guide

SHT-7540DN_rev09032008
Operational Manual
Digital Day & Night Box Color Camera
z1/3” Sony Super HAD CCD
z540 TV Lines, HQ-1 DSP
z0.15 Lux @ F1.0
Color mode automatically switches to B/W mode
under 2.0 Lux
zLead (Pb) Free RoHS Compliance
zDay & Night Feature
z12V DC / 24V AC
1. Lens mount
This mount is used to install a CS-mount lens.
CS-adaptor ring is required if use a C mount lens.
2.
Camera mounting screw holes
Screw hole for fixing camera.
3.
Mount Adaptor
This adaptor can be attached to either the top or bottom of the unit.
4.
Auto Iris Lens Connector (4-pin type)
The lens connector supplies the auto iris lens (not supplied) with DC
power and a video signal or DC control signal.
PIN NO. VIDEO DC
1 DC + 12V CONTROL -
2 NC CONTROL +
3 VIDEO SIGNAL DRIVE +
4 GND DRIVE -
5.
Control Switch
SW1. SYNC MODE: SYNC Mode Selection INT/L.L. switch.
SW2. AES: Automatic Electronic Shutter OFF/AES switch.
SW3. BLC: Back Light Compensation OFF/BLC switch.
SW4. F.L: Flickerless NOM/F.L switch.
SW5. AGC: Automatic Gain Control OFF/AGC switch.
6.
VIDEO connector
This is an output for connection to a video monitor, etc (75Ω).
7.
Iris mode selection switch Used to choose DC or VIDEO mode
according to the type of your lens.
8.
DC Level adjustment V.R. Used to adjust video output level of DC
driven auto iris lens.
9.
Power input terminal
Connect the power supply of 12V DC / 24V AC.
SW1. SYNC MODE: INT MODE: The camera may be operated
independently with its internal crystal control. L.L. MODE: This version
w/o L.L. function.
SW2. AES: AES: The automatic electronic shutter control 1/60(1/50) ~
1/100.000 sec. is employed for using a manual Iris Lens.
SW3. Example of Back Light Compensation: When the object is
dark by strong light (sun illumination etc) as (Fig 3-1). Please turn on
BLC switch. The object becomes as (Fig 3-2).
SH
T
-7540DN
SHT-7540DNP
FEATURES
CONTROL SWITCH OPERATION
Please read the Operational Manual
before attempting to use this product.
DIMENSIONS
(
Unit: mm
)
NOMENCLATURE AND FUNCTION

SHT-7540DN_rev09032008
SW4. F.L. (Flickerless): F.L: Fixes shutter speed at NTSC: 1/100 Sec.;
PAL: 1/120 Sec. When using this switch, set “AES” OFF. NOM: Normal
position.
SW5. AGC: AGC: level varies from 0 to 26dB. OFF: AGC level is fixed at 0
dB.
Model SHT-7540DN SHT-7540DNP
TV System NTSC PAL
Image Sensor 1/3” Sony Super HAD CCD
DSP Sony HQ-1
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Video Output 1.0Vp-p Composite / 75 ohms
Resolution 540 TV Lines
Minimum
Illumination
0.15 Lux @ F1.0
Color mode automatically switches to
B/W mode under 2.0 Lux
Scan System 2:1 Interlace
S/N Ratio More than 50dB (ACG OFF)
Electronic
Shutter Speed
AES ON:
1/60~1/100,000sec
AES OFF: 1/60sec
AES ON:
1/50~1/100,000sec
AES OFF: 1/50sec
Synchronization Internal
Back Light
Compensation ON / OFF Switchable
Auto Gain
Control ON / OFF Switchable
Flickerless ON / OFF Switchable
Lens Mount CS/C (with Adaptor)
Auto Iris
Control DC / Video Switchable
Power Supply 12V DC / 24V AC
Power
Consumption 166mA / 2.0W
Operation
Temperature 14°F ~ 122°F / -10°C ~ +50°C
Operation
Humidity RH 85% or less
Storage
Temperature -4°F ~ 140°F / -20°C ~ +60°C
Dimension 2.36”(W) x 1.97”(H) x 4.69”(L)
60mm(W) x 50mm(H) x 119mm(L)
Weight 0.88lbs / 400g
*Specifications are subject to change without notice
zOne (1) SHT-7540DN/SHT-7540DNP Camera
zOne (1) Allen Wrench
zOne (1) CS Adaptor Ring
zOne (1) Operational Manual
*For any returns, please include all components listed above with original
packaging in Resalable Condition. Absolutely No Returns will be
accepted if any component is missing/damaged or if any cable is cut or
tampered with.
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may
damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could
damage the camera.
3. Requires a proper operating environment
This camera is designed for indoor use. The allowable temperature
range for operation of this camera is between -10°C ~ 50°C and the
allowable humidity is 85%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before
lens installation or whenever the lens is changed. Cleaning should be
done by using a chamois, a very fine soft cloth, lens tissue, or cotton
tipped applicator and ethanol to carefully remove any fingerprint or
dust.
5. Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be connected to
a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire
or electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been exposed to rain or water.
d. If the video product has been dropped or the cabinet has been
damaged.
e. When the video product exhibits a distinct change in
performance.
OK-I USA products are covered under warranty for one year from the
date of purchase. The warranty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any
information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not
described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.
CAUTION
WARRANTY
SPECIFICATIONS
LIST OF COMPONENTS