Copyright © 2010. All Rights Reserved. EIVD36-42VF_I-316
REV12072010 EIVD36-42VFW_I-317
PIC I-316 I-317
Model EIVD36-42VF EIVD36-42VFP EIVD36-42VFW EIVD36-42VFWP
Base Color Metal White
TV System NTSC PAL NTSC PAL
Image Sensor 1/3” Sony Super HAD CCD
DSP Sony
Total Pixels 510(H)x492(V) 500(H)x582(V) 510(H)x492(V) 500(H)x582(V)
Video Output 1 Vp-p 75 Ω(Sync Negative Polarity)
Resolution 420 TV Lines
Minimum
Illumination 0.5 Lux @ F1.2 (0 Lux @ IR “on”)
S/N Ratio More than 48dB
Electronic
Shutter Speed 1/60~1/100,000
sec
1/50~1/100,000
sec 1/60~1/100,000sec
1/50~1/100,000
sec
Synchronization Internal
Gamma Control 0.45
Gain Control
uto
White Balance
uto
Back Light
Compensation Auto
IR LED 36 IR LED
IR Wavelength 850nm
IR Working
Distance 82~98ft / 25~30m
Lens 3.5mm~8.0mm Vari-Focal Lens
IP Rating
eatherproof IP65
Power Supply 12V DC
Power
Consumption 300~450mA IR LED "on"
90~110mA IR LED "off"
Operation
Temperature 14oF ~ 122oF / -10oC ~ +50oC
Dimension 5.12”(Ø) x 3.94”(H) / 130mm(Ø) x 100mm(H)
Weight 2.43 lbs / 1100g
* Specifications subject to change without notice
One (1) EIVD36-42VF/EIVD36-42VFP or
EIVD36-42VFW/EIVD36-42VFWP Camera with power/video cable
-One (1) Camera
-One (1) Mounting Ring
-One (1) Mounting Base
Four (4) Mounting Base Unit Screws
Four (4) Wall Anchors
One (1) Allen Wrench
One (1) Operational Manual
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may
damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could
damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between
14F ~ 122F / -10C ~ 50C.
4. Clean the front face to the pick-up device
It is recommended that the lens be cleaned every 3~6 months. Cleaning
should be done by using a chamois, a very fine soft cloth, lens tissue, or
cotton tipped applicator and ethanol to carefully remove any fingerprint
or dust.
5. Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be connected to
a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire
or electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been dropped or the cabinet has been
damaged.
d. When the video product exhibits a distinct change in
performance.
ADDITIONAL CAUTIONS:
Be careful not to shake the camera.
Please avoid places where direct sunlight may shine on the
camera.
Please avoid places where there are frequent vibrations or
shocks.
Please avoid places where the temperature exceeds 50oC or
temperatures lower than -10oC.
Please avoid storing and operating the camera in water.
Please avoid water spills on the video connectors and the DC
jack connectors.
FCC NOTICE:
This equipment has been tested and found to comply with the
limits for a class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates radio
frequency, and if not installed and used in accordance with the
instruction manual, may cause harmful interference.
This product is covered under warranty for one year from the date of
purchase. The warranty will automatically be voided if any of the
following occurs:
1.
Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any
information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not
described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
3.
Video or power cable is cut
The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.
CAUTIONS
WARRANTY
SPECIFICATIONS
PACKAGE CONTENTS
