SVD-248AI-Rev09/2007
Operational Manual
Vandal Proof 3-AXIS Vari-Focal D&N Dome
z1/3” Hi-Res. CCD
z480 TV Lines
z3.8mm~9.5mm Aspherical Vari-Focal Lens
z0.5 Lux @ F2.0
z3-AXIS design for any angle
zMulti Color Temperature for AWB
zDual Power 12V DC / 24V AC
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may
damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could
damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between -10°C ~ 50°C
and the allowable humidity is 85%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before lens
installation or whenever the lens is changed. Cleaning should be done by
using a chamois, a very fine soft cloth, lens tissue, or cotton tipped
applicator and ethanol to carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range. (Camera
must meet the specifications). Camera must be connected to a surge
protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire or
electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been dropped or the cabinet has been
damaged.
d. When the video product exhibits a distinct change in performance.
OKIUSA Products are covered under warranty for one year from the date
of purchase. The warranty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any
information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not
described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.
Model SVD-248AI
Image Sensor 1/3” Hi-Res. CCD
Total Pixels NTSC: 771(H) x 492(V)
PAL: 753(H) x 582(V)
Video Output 1.0Vp-p / 75 ohms
Resolution 480 TV Lines
Minimum
Illumination 0.5 Lux @ F2.0
Scan System 2:1 Interlace
S/N Ratio More than 48dB
Electronic
Shutter Auto and up to 1/100,000
Synchronization Internal
Gamma
Correction 0.45
Auto Gain Control Full Auto
Back Light
Compensation Full Auto
Auto White
Balance ATW with MCT Technology
(Multi Color Temperature AWB)
Aperture
Correction 2H Mode of H.V aperture correction
Lens 3.8mm~9.5mm Aspherical Vari-Focal Lens
(IR Cut)
Power Supply 12V DC / 24V AC
Power
Consumption 180mA +10% under 12V DC
Operation
Temperature -10oC ~ +45oC
Storage
Temperature -30oC ~ +60oC
Dimension 68.3mm(H) x 138mm(D)
Weight 492.4g
SVD-248AI
FEATURES
CAUTION
WARRANTY
SPECIFICATIONS
Please read the Operational Manual
before attempting to use this product.
