Okina USA SSB-7420DNP Quick start guide

SSB-7420DN_rev010809
Operational Manual
Mini Bullet Color Camera
z1/3” Sony Super HAD CCD
z420 TV Lines
z3.6mm Board Lens
z0.25 Lux @ F2.0
zIP67 Rating – Can be used for indoor/outdoor
z12V DC, Max. 100mA
1Camera mounting screw hole
Screw hole for fixing camera.
2Power input terminal
Connect the power supply of 12V DC.
3RCA terminal (Yellow)
This is a video output for connecting to a video monitor,
etc. (75Ω).
4BNC video connector
This is a video connector to connect the RCA terminal to
a BNC video monitor.
Model SSB-7420DN SSB-7420DNP
TV System NTSC PAL
Image Sensor 1/3" Sony Super HAD CCD
Total Pixels 537(H) x 505(V) 537(H) x 597(V)
Synchronization Internal
Resolution 420 TV Lines
Video Output 1.0Vp-p / 75Ω
Scanning System 2:1 Interlace
Gamma Correction 0.45
Minimum
Illumination 0.25 Lux @ F2.0
S/N Ratio More than 50dB
Digital D&N Mode Auto
(B/W Mode <2 Lux, Color Mode >5 Lux)
Auto Gain Control Auto
A
uto White Balanc
e
Auto
Electronic Shutter
Speed 1/60~1/100,000s 1/50~1/100,000s
Lens 3.6mm Board Lens / F2.0, 72.5°
Power Supply 12V DC
Power
Consumption 100mA / 1.2W
IP Rating IP67
Operation
Temperature 14˚F~122˚F / -10˚C~50˚C
Storage
Temperature -4˚F~140˚F / -20˚C~60˚C
Storage Humidity Max. RH90%
Dimensions 2.97”(L) x 1.04”(Ø)
75.5 (L) x 26.4 (Ø) mm
Weight 0.42 lbs / 190g (with bracket)
*Specifications are subject to change without notice
zOne (1) SSB-7420DN/SSB-7420DNP Camera with
video/power cable
zOne (1) Mounting Bracket
zThree (3) Mounting Screws
zThree (3) Wall Anchors
zOne (1) Video Connector
zOne (1) Spacer
zOne (1) Operational Manual
*For any returns, please include all components listed
above with original packaging in Resalable Condition.
Absolutely No Returns will be accepted if any component
is missing/damaged or if any cable is cut or tampered with.
SSB-7420DN
SSB-7420DNP
FEATURES
Please read the Operational Manual
before attempting to use this product.
SPECIFICATIONS
PACKAGE CONTENTS
DIMEN
S
I
O
N
S
(U
ni
t
: mm
)
PARTS AND FUNCTIONS
1
2
3
4

SSB-7420DN_rev010809
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong
light as this may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper
handling could damage the camera.
3. Requires a proper operating environment
This camera is designed for indoor and outdoor use. The
allowable temperature range for operation of this camera
is between 14˚F~122˚F / -10°C~50°C and the allowable
humidity is 90%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be
cleaned before lens installation or whenever the lens is
changed. Cleaning should be done by using a chamois, a
very fine soft cloth, lens tissue, or cotton tipped
applicator and ethanol to carefully remove any fingerprint
or dust.
5. Check the power source voltage
The power source voltage should be within the specified
range. (Camera must meet the specifications). Camera
must be connected to a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this
may touch dangerous voltage points of short out parts
that could result in a fire or electric shock. Never spill any
kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all service to
qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer
service to qualified servicing personnel under the
following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the video product.
c. If the video product has been exposed to rain or
water.
d. If the video product has been dropped or the
cabinet has been damaged.
e. When the video product exhibits a distinct change
in performance.
OKINA USA products are covered under warranty for one
year from the date of purchase. The warranty will
automatically be voided if any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to
confirm any information regarding when and where the
product was purchased. We have no other way to verify
the purchase record without the serial number on the
camera sticker; therefore, it should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a
manner not described in this manual, the warranty will
be voided immediately. It is the customer’s responsibility
to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be
tampered with. Cutting or modifying of the cables will
result in termination of the warranty.
CAUTION WARRANTY