Okina USA EIVD24-42VF Quick start guide

EIVD24-42VF-Rev07/2007
EIVD24-42VF
Operational Manual
Waterproof IR Dome Color Camera
1/3” Sony Super HAD CCD
420 TV Lines
24 IR LED
240~300mA IR LED “on” / 90~110mA IR LED “off”
IR Distance 45~65ft / 14~20m
3.5mm~8.0mm Vari-Focal Lens
Waterproof IP65 Rating
12V DC
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may
damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could
damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between -10C ~ 50C
and the allowable humidity is 85%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before lens
installation or whenever the lens is changed. Cleaning should be done by
using a chamois, a very fine soft cloth, lens tissue, or cotton tipped
applicator and ethanol to carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range. (Camera
must meet the specifications). Camera must be connected to a surge
protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire or
electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been dropped or the cabinet has been
damaged.
d. When the video product exhibits a distinct change in
performance.
OKIUSA Products are covered under warranty for one year from the date
of purchase. The warranty will automatically be voided if any of the
following occurs:
1.
Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any
information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not
described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
3.
Video or power cable is cut
The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.
4.
Returns
You may return new, unused items sold and fulfilled by an authorized
distributor of OKIUSA products within 14 days of purchase for a full
refund (Restocking fee may occur). It must include the camera,
mounting bracket (if any), screws, and operational manual. Items
must be returned in their original packaging. Please submit returns to
the authorized OKIUSA distributor from which you purchased the
product(s).
5. Exchanges
After 14 days from date of invoice, the product can be exchanged for
the same item if it is found defective by OKIUSA, and is within the
1-year warranty period. In this case, please contact an authorized
distributor of OKIUSA products to obtain an RMA number from
OKIUSA, and follow the instructions given.
FCC NOTICE:
This equipment has been tested and found to comply with the
limits for a class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates radio
frequency, and if not installed and used in accordance with the
instruction manual, may cause harmful interference.
Package Contents:
One (1) EIVD24-42VF Camera with power/video cable
Four (4) Screws
Four (4) Wall Anchors
One (1) Allen Wrench
One (1) Operational Manual
ADDITIONAL CAUTIONS:
Be careful not to shake the camera.
Please avoid places where direct sunlight may shine on the
camera.
Please avoid places where there are frequent vibrations or
shocks.
Please avoid places where the temperature exceeds 50oC or
temperatures lower than -10oC.
Please avoid storing and operating the camera in water.
Please avoid water spills on the video connectors and the DC
jack connectors.
FEATURES
CAUTIONS
WARRANTY
Please read the Operational Manual
before attempting to use this product.

EIVD24-42VF-Rev07/2007
Model EIVD24-42VF
Image Sensor 1/3” Sony Super HAD CCD
DSP Sony
Total Pixels NTSC: 510(H) x 492(V)
PAL: 500(H) x 582(V)
Video Output 1 Vp-p 75 Ω(Sync Negative Polarity)
Resolution 420 TV Lines
Minimum
Illumination 0.5 Lux @ F1.2 (0 Lux @ IR “on”)
S/N Ratio More than 48dB
Electronic
Shutter Speed 1/50~1/100,000sec
Synchronization Internal
Gamma Control 0.45
Gain Control Auto
White Balance Auto
Back Light
Compensation On/Off Switchable
IR LED 24 IR LED
IR Wavelength 850nm
IR Working
Distance 45~65ft / 14~20m
Lens 3.5mm~8.0mm Vari-Focal Lens
IP Rating Waterproof IP65
Power Supply 12V DC
Power
Consumption 240~300mA IR LED “on” 90~110mA IR LED “off”
Operation
Temperature -10oC ~ +50oC
Dimension 130mm(D) x 100mm(H)
Weight 1100g
1. Unscrew the three mounting screws on the bottom mounting plate half
way using the Allen Wrench. Do not unscrew the screws all the way,
unless you have a safe place to store the screws.
2. Unscrew the mounting ring as specified in the picture. If you are
having trouble removing the bottom mounting plate, unscrew the three
mounting screws slightly (without removing the screws) and retry.
3. Lift the two mounting rings off the base, making sure that the three
mounting screws do not fall off.
4. Screw two of the base unit screws into the base unit and onto the
ceiling/wall.
5. Insert the cable through the base unit and connect the cable.
6. Screw the remaining two base unit screws into the base unit to
secure it on the ceiling/wall. Be sure that all screws are tightened.
7. Align the mounting rings so that the arched area is above the IR
LED light. Make sure the ring does not cover any part of the IR LED
light because it will reflect the light back into the camera during
nighttime.
8. Location of the vari-focal lens adjustor.
SPECIFICATIONS
DIMENSIONS
(
Unit: mm
)
INSTALLATION INSTRUCTIONS
Yes No