Okina DHE-04 User manual

MADE IN TAIWAN DV-13 / DV-14 / DV-15
Copyright © 2014 OKINA USA. All rights reserved. R201405-V09
Please read this Quick Setup Guide before installation.
*Notes: Any Return Must Include All Components.
Additional charges apply for any missing components. A UPS Battery Backup System is
highly recommended to avoid power failure restoration damage to Hard Drive & Motherboard.
**Quick Setup Guide & User’s Manual are subject to change without notice.
A.
One (1)
DHE-04 / DHE-08 / DHE-16 DVR
B.
One (1)
Remote Controller
C.
Two (2)
AAA Battery for Remote Controller
D.
One (1)
USB Mouse
E.
One (1)
4 Screw on Terminal Connector - DHE-04
One (1)
8 Screw on Terminal Connector - DHE-08
F.
Six (6)
Four (4)
Hard Drive Screws – DHE-04 / DHE-08
Hard Drive Screws – DHE-16
G.
One (1)
12V DC / 5Amp Power Supply
H.
Two (2)
SATA Cable Inside
I.
One (1)
Quick Set up Guide Book
J.
One (1)
User’s Manual & CMS Software CD
A.
B.
C.
D.
E.
F.
G.
H.
Inside the DVR
I.
J.
DHE-04
DHE-08
DHE-16
960H H.264 DVR – 4 / 8 / 16 CH.
Quick Setup Guide
PACKAGE CONTENTS
x 6 (4 / 8 CH.)
x 4 (16 CH.)
x 1
x 1 (4 CH.)
x 1 (8 CH.)
x 2

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 2 -
1. Front Panel
Item # Label Name Function
1 MENU / + Enter menu page / increase value
2 BACKUP / - Enter backup page / decrease value
3 PLAY / IRIS Enter Playback/ iris adjustment (PTZ)
4 REW / SPEED Fast rewind on playback mode / speed adjustment (PTZ)
5 STOP / ESC
Stop playback on playback mode /
Exit menu or jump back to previous page
6 FF / P.T.Z. Fast forward on playback mode /enter PTZ mode
7 REC / FOCUS Manual record / focus adjustment(PTZ)
8 SEARCH / -
9 Enter Validate action
10 Split / Direction Key Switch split / Move selected item
11 USB Connect USB thumb drive or mouse
12 IR receiver Remote receiver
2. Back Panel – 4 CH.
Item # Label Name Function
1 Audio out Audio output, connect to the sound box
2 Audio in 4 CH Audio input
3 ALARM in Connect to external sensor 1-4
4 ALARM out 1-ch relay output. Connect to external alarm
5 GND Grounding for Alarm IN
PANEL DEFINITION

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 3 -
Item # Label Name Function
6 Video in Video input channels from 1-4
7 CVBS port Connect to monitor
8 Spot out
Connect to monitor as an AUX output channel by channel. Video would be
displayed without OSD.
9 VGA port VGA output, connect to monitor
10 HDMI port Connect to high-definition display device
11 LAN Network port
12 USB port Connect USB mouse or connect external USB devices
13 DC12V POWER INPUT
14 RS485 Connect to speed dome or keyboard
3. Back Panel – 8 CH.
Item # Label Name Function
1 Audio in 4 CH Audio input
2 GND Grounding for Alarm in
3 ALARM OUT 1-ch relay output. Connect to external alarm
4 ALARM IN Connect to external sensor 1-8
5 Video in Video input channels from 1-8
6 VGA port VGA output, connect to monitor
7 HDMI port Connect to high-definition display device
8 LAN Network port
9 USB port Connect USB mouse or connect external USB devices
10 DC12V POWER INPUT
11 RS485 Connect to speed dome or keyboard
12 Audio out Audio output, connect to the sound box
13 CVBS port Connect to monitor
14 Spot out
Connect to monitor as an AUX output channel by channel. Video would be
displayed without OSD.

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 4 -
4. Back Panel – 16 CH.
Item # Label Name Function
1 RS485 Connect to speed dome or keyboard（A is TX+, B is TX-）
2 Audio in 2-CH Audio inputs
3 Video in Video input channels from 1-16
4 HDMI port Connect to high-definition display device
5 VGA port VGA output, connect to monitor
6 LAN Network port
7 USB port Connect USB mouse or connect external USB devices
8 DC12V POWER INPUT
9 Video out Connect to monitor
10 Audio out Audio output, connect to the sound box
1. Remote Controller
◆This remote control uses AAA battery, the definition as following:
Item # Label Name Function
1
Record Button
To record manually
2 0-9, -/-- Digital Button Input number or choose camera
3 Fn1 Button Unavailable temporarily
4 Multi Button To choose multi-screen display mode Next Button To switch the live image
SEQ To enter into auto dwell mode
5 Switch To switch the output between BNC and VGA
CONTROL OPTION

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 5 -
Item # Label Name Function
6
Direction button
To move cursor in setup or pan/title PTZ
7 Exit Button To exit the current interface
8 Focus/IRIS/Zoom/PTZ To control PTZ camera. Move camera/zoom/IRIS/Focus
9
Preset Button To enter into preset setting in PTZ mode
Cruise Button To enter into cruise setting in PTZ mode
Wiper Button To enable wiper function in PTZ mode
Light Button To enable light function in PTZ mode
10
Track Button To enter into track setting in PTZ mode
Clear Button To return to the previous interface
Fn2 Button Unavailable temporarily
Info Button Get information about DVR like firmware version, HDD information
11
Snap Button To take snapshots manually
Search Button To enter into search mode
Cut Button To set the start/end time for backup in playback mode
Backup Button To enter into backup mode
Zoom Button To zoom in the images
PIP Button To enter into picture in picture setting mode
12 Power Button Switch off—to stop DVR. Use it before turning off the power
13 Audio To enable audio output in live mode
14 Enter Button To confirm the choice or setup
15 Menu Button To enter into menu
16
To control playback. Play/Pause/Stop/Previous-Section/
Next-Section/Rewind/Fast Forward
◆Switch Remote Control ID
1. Take remote control and point to DVR then continuously press “8”,”8”,”ID(0-65535)”,”Enter”.
2. Make change on DVR ID Setting,
Go to “SYSTEM MENU” > “DEVICE ID” to make change
＊The ID must be the same on DVR.
＊For example: If ID=1 ,
Please take remote control and point to DVR then press 8,8,1,Enter.
Then go to “SYSTEM MENU” > “DEVICE ID” change the ID=1
2. Mouse Control: REQUIRED
◆Connection: Recommend to connect the USB mouse to the back panel.
◆Mouse functions：
1）Under LIVE mode：
On every channel，you could double click the left button to switch FULLSCREEN and double click again to
switch back to original split mode.
On every channel，you could single click right button to popup MENU page.
2）Under MENU page：
Single click left button on any functional icon could enter the function page and Single click right button to
exit function page or jump back to previous page.
If you want to key in letter or digit, please move mouse to textbox then single click left button on textbox.
The OSD keyboard will pop up as following,

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 6 -
3）Under Backup mode：
Single click left button to select item, single click right button to jump back to previous page.
4）Under PTZ mode：
Single click left button to operate PTZ function, single click right button to jump back to previous page.
1. Wizard for language and time setup
2. Wizard for Record setup
2.1 Motion Detection Recording:
Motion Detection Recording: Enter Main Menu Setup Alarm Motion
Enable the Channels to turn on Motion Detect Record.
**Motion Schedule Default: is set to Full Time motion recording on all channels.
If Schedule Motion Recording needs to be changed:
WIZARD SETUP
Device Name: to set a name of DVR.
Language: to set a proper language.
Date Format: to set a proper display format of time.
Time Format: to set 24 hour or 12 hour format to display.
Time Zone: to set proper time zone (GMT-8: Los
Angeles)
＊Caution: Please make sure to set time zone correctly.
To prevent getting different time stamps between local
and remote site.
System Date: to set current system date time.
Please click “next” to next wizard process.
You can setup record frame rate and quality for each
channel and change record resolution.
Adjustable parameter as following,
Resolution: CIF, HD1 or D1
Frame rate: Number of channel.resolution@NTSC frame rate
(PAL frame rate)
4 CH 4CIF@30(25) 4HD1@30(25) 4D1@30(25)
Quality: Highest/ Higher/ Normal/ Low/ Lower/ Lowest
If you want to change all channel setup at once, please
click “All” then setup resolution, frame rate and quality at
right hand side.
Please click “next” to next wizard process.

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 7 -
To modify motion recording schedule click on the pencil icon located on the upper right of the screen, then
click on desired days and times to schedule recording when motion trigger.
If same schedule apply to all channels. After highlighting desired squares apply settings to “All” Channel, click
“Copy”and click Apply to save setting. To Enable full time motion Recording,highlight the entire Blue Grid.
2.2 Full Time Recording :
1. Press “Record” Button on the front panel of the DVR. Green box will appear on screen to confirm that
manual recording is enabled. Press “Record” Button again to stop recording.
OR Right click on main screen and select “Record”.
Note: Definition of Holding Time (on motion detect setting) :
After motion record is activated and there is NO activity within 10 seconds this will be handled as one event.
Otherwise if there IS activity within that time frame it will continue recording.
Note: Change Daylight Savings on the first week of March and second week of November.
3. Wizard for HDD setup
You can format HDD by using “Format” function.
After HDD format completed, it will show
“Normal”label on status.
＊Please make sure to backup all HDD data
before you format the HDD.
All HDD data will be erased after HDD formatted.
Please click “Finish” to get into login page.

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 8 -
Part 1. Static IP Address
1. Enter Main Menu screen by pressing the MENU
button on the front panel of the DVR.
Then enter password “123456” and click Login
2. Select Setup.
3. Select Network.
4.
Select “Obtain an IP address automatically,”
turn on this feature.
Then Select Apply at the bottom of the screen to
restart the network.
This will generate a new IP Address.
(Make sure Ethernet Cable is plugged in)
5. After Apply, the IP Address, Netmask, Gateway, and DNS addresses should automatically be generated.
*For STA
TIP: Write down HTTP Port, Server Port, and IP Address on a piece of paper for reference. You will need
these numbers later in the installation.
TIP: If you do not know a DNS address and the DVR did not populating those fields by itself, try 8.8.8.8 and
8.8.4.4. These are Google's public DNS addresses, and in addition to working well.
6. Uncheck “Obtain an IP address automatically” to turn off this feature and make IP Address stay the
same. Then click Apply.
Continued For DDNS
Set up Part 2
NETWORK SETUP: STATIC IP ADDRESS & DDNS

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 9 -
Part 2. DDNS
1. Continue Part 1: Select “Other Setting” from the Tab bar and turn on DDNS.
2. Select DDNS Type and pick one website from the given field to register your Host Domain Name.
3. Enter User Name, Password, and Host Domain info that you registered for DDNS and click Test - After Test
passes, then click Apply and Exit.
4. Finally, you will need to set port forwarding on your internet-facing router/gateway to direct port 80 traffic to
the DVR. Also you will need to port forwarded your server port 6036 to stream video and audio as well.
Locate the page in your router settings to set port forwarding (may also be labeled “firewall”).
HTTP Port: Port for IE connection. (Default is 80)
80
Server Port: Port for video and audio streaming.
(Default is 6036)
6036
Incoming Port Range (advance)
80-80 (or alternative if port 80 is being used)
Forward Port (advance)
80, 6036
IP
Your DVR’s internal IP, typically 192.168.x.x
Protocol (advanced)
TCP & UDP
TIP: Some consumer router/gateway devices may present the firewall settings as a list of services toforward. In this
case, consult the manual for settings for creating a custom service and use the above values. For router/gateway
devices provided by your ISP, please contact your ISP technical support.
TIP: AutoDDNS do not need to register online. This
can just register on DVR.
The DDNS URL will always be in the form of
<hostname>.
If you are unable to access the DVR from the
internet using the DDNS URL, but the IP works,
please double check that you have the DDNS URL
correctly typed

DHE-04 / DHE-08 / DHE-16 Quick Setup Guide
DV-13 / DV-14 / DV-15
R201405-V08
- 10 -
Item #
DDNS Server Website
Item #
DDNS Server Website
1
www.dyndns.com
4
www.dvrdydns.com
2
www.meibu.com
5
www.mintdns.com
3
www.no-ip.com
6
www.autoddns.com
*For technical specification, please refer to the User Manual.
www.okinausa.com DV-13 / DV-14 / DV-15
Copyright © 2014 OKINA USA. All rights reserved. R201405-V09
MOBILE APP: SUPER LIVE PRO
DDNS HOSTING SERVER