Okina WDE-7680 User manual

Copyright © 2010. All Rights Reserved.
www.okinausa.com i REV122010-V17
WDE-7680 680 TVL
WDE-7610 610 TVL
Hyper Wide Dynamic Camera - Effio WDR
User Manual
Thanks for purchasing our product. Before operating the unit, please read the instructions carefully
and keep this manual for future reference.

Copyright © 2010. All Rights Reserved.
www.okinausa.com ii REV122010-V17
Safety Warnings
1. Read this manual carefully before installing the unit
Please read this manual first for correct installation and operation.
2. Never install the camera on a ceiling that cannot hold its weight
The product may fall down and cause damages.
3. Never install the camera near electric or magnetic fields
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices would distort the
video image.
4. Never install or use the camera in areas exposed to water, oil or gas
The water, oil or gas may result in operation failure, electric shock or fire. Do not use this
unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, near a swimming pool, in an unprotected outdoor installation, or any area
which is classified as a wet location.
5. Never face the camera toward the sun
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
6. Power Cord Protection
Touching the wet power cord with hands or touching the power cord with wet hands may
result in electric shock. Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, playing particular
attention to cords and plugs, convenience receptacles, and the point where they exit
from the appliance.
7. Attachments
Do not use attachment not recommended by the product manufacturer as they may
cause hazards.
8. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind onto the product.
9. Do not operate the camera in environments where the temperature, humidity
or power source is beyond the specified ones
Use the camera in suitable environments where the temperature is within -10°C~50°C
and humidity below 90%. Use the input power source as the specifications listed.

Copyright © 2010. All Rights Reserved.
www.okinausa.com iii REV122010-V17
10. Cleaning
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
11. Never disassemble the camera nor put impurities in it
Disassembly or impurities may result in trouble or fire.
12. Stop using when the product emits smoke or abnormal heat
13. Servicing
Do not attempt to repair this unit yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
14. Retain Instructions
THE SAFETY AND OPERATING INSTRUCTIONS SHOULD BE RETAINED FOR
FUTURE REFERENCE.
Warranty
OKINA USA products are covered under warranty for one year from the date of purchase. The
warranty will automatically be voided if any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any information regarding
when and where the product was purchased. We have no other way to verify the purchase
record without the serial number on the camera sticker; therefore, it should not be removed.
2. Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not described in this manual,
the warranty will be voided immediately. It is the customer’s responsibility to keep the
camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with. Cutting or modifying of
the cables will result in termination of the warranty.
NOTE:
The information in this manual was up-to-date when published. The manufacturer reserves the
right to revise and improve its products. All specifications are therefore subject to change without
notice.

Copyright © 2010. All Rights Reserved.
www.okinausa.com iv REV122010-V17
Table of Contents
1. INTRODUCTION .............................................................................................................................. 1
1.1 MAIN FEATURES ............................................................................................................................ 1
1.2 CONTENT LIST............................................................................................................................... 1
1.3 SPECIFICATIONS ............................................................................................................................ 2
2. CAMERA OVERVIEW...................................................................................................................... 3
2.1 DIMENSIONS.................................................................................................................................. 3
2.2 DESCRIPTION OF CAMERA PARTS.................................................................................................... 4
3. OSD OPERATION............................................................................................................................ 6
3.1 OSD CONTROL BUTTONS............................................................................................................... 6
3.2 OSD OPERATION........................................................................................................................... 7
4. CONFIGURATION............................................................................................................................ 8
4.1 LENS........................................................................................................................................... 8
4.2 AGC............................................................................................................................................. 9
4.3 WDR.......................................................................................................................................... 10
4.4 WHITE BALANCE CONTROL ...................................................................................................... 12
4.5 2D &3D NR (DYNAMIC NOISE REDUCTION)................................................................................... 14
4.6 DAY/NIGHT ............................................................................................................................... 16
4.7 SHUTTER ................................................................................................................................. 20
4.8 IMAGE....................................................................................................................................... 22
4.9 EFFECT .................................................................................................................................... 23
4.10 SYSTEM ................................................................................................................................. 26
4.11. BALUN FUNCTION (UTP) ........................................................................................................... 28
4.12. EXIT ....................................................................................................................................... 28

Copyright © 2010. All Rights Reserved.
www.okinausa.com 1 REV122010-V17
1. Introduction
WDE-7680 and WDE-7610 are built with Sony’s latest image processor, this
super-wide dynamic camera has the capability of achieving resolutions of over
680TVL or 610TVL respectively. The features include 2-D and 3-D noise
reduction, sense up, spot removal, strong-light suppression, intelligent motion,
face detection and OSD functions. The camera also comes with 256x digital zoom,
an intelligent auto exposure compensation system and an RS-485 remote control.
WDE-7680 / WDE-7610 reproduces nearly perfect images like no other.
1.1 Main Features
WDE-7680
Color: 680 TVL, B/W: 700 TVL
Powerful 510x WDR (54dB)
WDE-7610
Color: 610 TVL, B/W: 630 TVL
Powerful 256x WDR (53dB)
1/3" Hyper Wide Dynamic Color Camera, Effio WDR DSP
Color: 0.03 Lux @ F1.0, B/W: 0.01 Lux @ F1.0, Sense-up: 0.0001 Lu[email protected]
Multi-Language OSD Control / RS485 Control
Ideal for Backlight Environments
2D/3D Noise Reduction & Sense Up (512x) Functions
High Contrast Images
Face Detection of up to 4 faces
E-zoom Function (1~256x)
Advanced Motion Detection Function
Polygonal Mosaic Privacy Mask
Freeze / Timer Clock
12V DC / 24V AC, 3.0W
1.2 Content List
One (1) WDE-7680 or WDE-7610 camera
One (1) Female DC Connector
One (1) CS Mount Ring
One (1) DC Plug
One (1) Allen Wrench
One (1) Warning Sign Sticker
One (1) User Manual
One (1) CD
*For any returns, please include all components listed above with original packaging in Resalable
Condition. Absolutely No Returns will be accepted if any component is missing/damaged or if
any cable is cut or tampered with.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 2 REV122010-V10
1.3 Specifications
PIC T-408 T-410
Model WDE-7680 WDE-7610
Image Sensor 1/3" Sony 760H Double-speed (Double-density) CCD
Number of Total Pixels NTSC: 1028(H)x508(V)
PAL: 1024(H)x596(V)
NTSC: 811(H)x508(V)
PAL: 795(H)x596(V)
Resolution ; DSP Color: 680 TVL, B/W: 700 TVL
Sony Effio WDR
Color: 610 TVL, B/W: 630 TVL
Sony Effio WDR
Minimum Illumination Color: 0.03 Lux @ F1.0; B/W: 0.01 Lux @ F1.0; Sense-up: 0.0001 Lux @ F1.0
Wide Dynamic Range 510x Normal Camera (54dB) 256x Normal Camera (53dB)
Video Output 1.0Vp-p Composite, 75Ω(BNC), S-Video (Y/C)
Signal to Noise Ratio More than 52dB (AGC off, Weight on)
Gamma Correction 0.45
Menu OSD Control or by RS485 Control
Title TITLE (LOCATION)
Synchronizing System INTERNAL / LINE CLOCK
Digital Day&Night Mode COLOR / B&W / AUTO / EXT / SCHEDULE
Electronic Shutter AUTO(1/50(60)~1/100,000sec.) / SCHEDULE or DAY&NIGHT / MANUAL:
1/50(60), FL 1/120(100), 1/200, 1/250, 1/350, 1/500, 1/750, 1/1,000, 1/1,500,
1/2,000, 1/3,000, 1/4,000, 1/10,000, 1/30,000, 1/60,000, 1/100,000 sec.
Automatic Gain Control AUTO / MANUAL / OFF
White Balance ATW / AWB / AWC (Push Lock) / MANUAL /
OUTDOOR(1800°K~10500°K) / INDOOR(4500°K~8500°K) / ANTI CR
Back Light Compensation WDR / BLC / OFF
Flickerless ON / OFF
Dynamic Noise Reduction 3D / 2D
Sense Up AUTO (Limit x2~x512) / OFF
Face Detection 4 Face Detection
Language ENGLISH / TRADITIONAL CHINESE / SIMPLIFIED CHINESE
E-Zoom X1~x256, Pan / Tilt Adjustable
Motion Detection ; Privacy ON / OFF (24x16 Zones, Alarm) ;
ON / OFF (16 Zones Programmable, Polygonal Mosaic)
Timer Clock Year/Month/Date, Hour/Minute/Second
Camera Control Interface RS485 Interface OSD Control by Pelco-D, Pelco P
Automatic IRIS ; Connector VIDEO / DC ; D4 IRIS Jack
Lens Mount C / CS mount (With Adaptor)
Lens Not Included
Power Input ; Consumption 12V DC / 24V AC (10.8~39V DC / 24V AC) ; 3.0W
Operation ; Storage Temp. 14˚F~122˚F ; -4˚F~140˚F / -10˚C~50˚C ; -20˚C~60˚C
Operation ; Storage Humidity Maximum: RH80% ; RH90%
Dimensions 2.36”(W) x 1.97”(H) x 4.68”(L) / 60mm(W) x 50mm(H) x 119mm(L)
Net Weight 0.77 lbs / 350g
* Specifications are subject to change without notice.
PAL version also available.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 3 REV122010-V17
2. Camera Overview
2.1 Dimensions
IRIS

Copyright © 2010. All Rights Reserved.
www.okinausa.com 4 REV122010-V17
AC24V
2.2 Description of Camera Parts
(1) Lens Mount
This mount is used to install a CS-mount lens. CS-adaptor ring is required when using a C
mount lens.
(2) Camera Mounting Screw Holes
Screw hole for mounting the camera.
(3) Mount Adaptor
The adaptor can be attached onto the top or the bottom of the unit.
(4) Auto Iris Lens Connector (4-pin type)
The lens connector supplies the auto-iris lens (not supplied) with DC control signal.
(5) S-Video Output Terminal
Separate Y (brightness) and C (color) signal are outputs from this terminal to obtain better
video quality at a video monitor.
1. C signal: 0.3V (p-p), 75Ω, unbalance
2. Y signal: 1.0V (p-p), 75 Ω, unbalance, negative synchronizing
3. C signal Ground
4. Y signal Ground
(6) Iris Mode Selection Switch
Select DC or VIDEO mode according to the lens.
(7) OSD Control Buttons
ENTER button
UP & DOWN buttons
LEFT & RIGHT buttons
(8) Video Connector
Video can be outputted via this BNC connector (75Ω).
PIN NO. VIDEO DC
1 DC + 12V CONTROL -
2 NC CONTROL +
3 IRIS DRIVE +
4 GND DRIVE -

Copyright © 2010. All Rights Reserved.
www.okinausa.com 5 REV122010-V17
(9) Communication Connectors
1. RS485+
2. RS485-
3. Day & Night External Input (controlled by external infrared illuminator)
4. Day & Night Output
5. Alarm Out
6. Ground
(10) Power Input Indicator Light
When the camera is connected to a power source, the indicator light will be on.
(11) RS485 Terminal Impedance Switch
Set the first and the last equipment terminal impedances as 120Ωand set the rest parallel
connection equipment in the middle as HiZ to obtain the best transmitting status.
(12) Power Input Terminal
Connect the power input of 12V DC / 24V AC (10.8~39V DC / 24V AC).

Copyright © 2010. All Rights Reserved.
www.okinausa.com 6 REV122010-V17
3. OSD Operation
3.1 OSD Control Buttons
① UP
Use this button to move the cursor upwards to the desired item.
② RIGHT
Use this button to move the cursor to the right to select or to adjust the parameters of
the selected item. The parameter increases when the right button is pressed.
③ DOWN
Use this button to move the cursor downwards to the desired item.
④ LEFT
Use this button to move the cursor to the left to select or to adjust the parameters of
the selected item. The parameter decreases when the left button is pressed.
⑤ ENTER
Use this button to display the main menu, to confirm and to enter the submenus when
they’re available. Items with “<┘” symbol in the end contain sub-menus. For further
settings of those items, select the desired item with the button cor dand press the
ENTER button to bring up the sub-menu and edit.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 7 REV122010-V17
3.2 OSD Operation
1. Start to operate the OSD menu
Press the ENTER button to bring up the OSD main menu to start operating OSD
menus.
2. Select items with the cursor buttons
yUse buttons cand dto move the cursor up and down.
yUse buttons eand fto switch the modes or to adjust the parameters or the values
of the settings.
3. Switch to the sub-menu
Items with “<┘” symbol in the end contains sub-menus. For further settings of those
items, select the desired item with the button cor dand press the ENTER button to
bring up the sub-menu and edit.
4. Return to the previous page
Select RETURN and press the ENTER button to return to the previous page.
5. Exit the OSD menu
Select EXIT with the button cor dand press the ENTER button to exit the OSD menu.
Main Menu
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘
**LENS**
LENS DC<┘
BRIGHTNESS 14
SPEED 0
RETURN EXIT
Sub-Menu

Copyright © 2010. All Rights Reserved.
www.okinausa.com 8 REV122010-V17
4. Configuration
4.1 LENS
When the MAIN MENU is displayed on the screen, use the UP and DOWN buttons to the
LENS and press the ENTER button to do further setups.
*LENS
yWhen the DC LENS is in use, push IRIS SWITCH on the control board to DC, and the
LENS status on the menu will be displayed as DC.
yWhen the VIDEO LENS is in use, push IRIS SWITCH on the control board to VIDEO,
and the LENS status on the menu will be displayed as VIDEO.
*BRIGHTNESS
When the LENS MENU is displayed on the screen, use the UP and DOWN buttons to the
BRIGHTNESS and use LEFT and RIGHT buttons to adjust the screen brightness from level
0to 63.
*SPEED
The range of the SPEED can be set from -31 to 32. The speed of DC Lens is in direct ratio to
the number you set.
NOTE:
The SPEED function will not work when the LENS set to VIDEO.
**LENS**
LENS DC<┘
BRIGHTNESS 14
SPEED 0
RETURN EXIT
Sub-Menu of LENS
Main Menu
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘

Copyright © 2010. All Rights Reserved.
www.okinausa.com 9 REV122010-V17
4.2 AGC
When the MAIN MENU is displayed on the screen, use the UP and DOWN buttons to the
AGC and press the ENTER button to do further setups.
*AGC MAX
1. Select the AGC and press LEFT and RIGHT buttons to adjust the AUTO GAIN
CONTROL settings. Options are AUTO, OFF, and MANUAL.
2. There’s a submenu under the mode MANUAL, press ENTER button to do further setups.
The AGC MANUAL range under the MANUAL mode can be set from 0to 15.
3. The higher the number, the brighter the screen can be. And the noise will also be higher.
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘
**AGCMANUAL**
AGC MAX 3
RETURN EXIT
There’re 3 options under AGC: AUTO, OFF and
MANUAL.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 10 REV122010-V17
4.3 WDR
1. When the MAIN MENU is displayed on the screen, use the UP and DOWN buttons to
WDR and press the ENTER button to do further setups.
2. Please select the desired item and press LEFT and RIGHT buttons to adjust the settings.
*WDR (Wide Dynamic Range)
When there are both bright and dark areas at the same time, selecting this mode makes
both areas distinctive.
*LEVEL
Use the LEVEL function to decrease the brightness of the bright area.
Level: 1~32
*XDR
Use the LEVEL function to increase the brightness of the dark area.
Level: OFF~15
Sub-Menu under WDR mode.
There’re 3 modes under WDR function: WDR,
BLC, and OFF.
* * WDR **
LEVEL
XDR
EXIT
18
OFF
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘

Copyright © 2010. All Rights Reserved.
www.okinausa.com 11 REV122010-V17
*BLC (Back Light Compensation)
Even when there is a massive backlight behind the object, bright images of the background
and the object can still be captured by selecting the BACKLIGHT mode.
Level: 1~14
*OFF
When set as OFF, there’ll be no wide dynamic range.
**BLC**
LEVEL 6
RETURN EXIT
Options under this mode are
Level : 1~14.
Sub-Menu under BLC mode.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 12 REV122010-V17
4.4 WHITE BALANCE Control
The screen color can be adjusted by using the WHITE BALANCE function.
1. Please use the UP and DOWN buttons to WHITE BALANCE on the MAIN MENU and
press the ENTER button to do further setups.
2. Please select the desired item and press LEFT and RIGHT buttons to adjust the settings.
*ATW (Auto Tracking White Balance)
This mode can be used within the color temperature range from 1800°K to 10500°K (e.g.,
around fluorescent lights, outdoors, around sodium vapor lamps or inside tunnels).
*AWB (Auto White Balance)
Select this to allow the camera automatically adjust the white balance under all conditions.
* AWC (Push Lock)
To find the optimal setting for the current luminance environment in this mode, point the
camera towards a sheet of white paper and press the ENTER button. Whenever the
condition changes, readjust it.
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘
Sub-Menu under AWC mode.
**AWC **
PRESS AND HOLD
ENTER BUTTON
UNTIL AWC COMPLETED.
**AWC **
COMPLETED
PRESS ENTER RETURN
Follow the instructions
shown on the screen to
complete the setting.
Sub-Menu under AWC mode.
There’re 6 modes under this function: ATW,
AWB,
AWC (Push Lock), MANUAL, OUTDOOR,
INDOOR and .ANTI CR.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 13 REV122010-V17
*MANUAL
The manual adjustment mode enables a more precise adjustment. Increase and/or decrease
the red and blue color values according to the color changes of the object to set the suitable
color temperature.
RED color vale ranges from 0to 255.
BLUE color value ranges from 0to 255.
*OUTDOOR
Select this when the color temperature is around 6300°K.
*INDOOR
Select this when the color temperature is around 3200°K (when surrounded by sodium
lights).
*ANTI CR (Color rolling suppression)
Select to set the white balance mode to the ANTI CR mode.
NOTE:
The White Balance can not fully function under the following conditions. When the
following occurred, please select AWC Mode.
<When there’s a higher temperature surrounded the object.
<When there’s darkness surrounded the object.
<When there’s a fluorescent light surrounded the object or where the light changes all the
time.
Sub-Menu under MWB mode.
**MWB**
RED 30
BLUE 25
RETURN EXIT
RED color value ranges from 0to 255.
BLUE color value ranges from 0to 255.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 14 REV122010-V17
4.5 2D &3D NR (Dynamic Noise Reduction)
1. When the noise level is reduced, the camera performance can apparently be
improved. When recording digitally, the image file size can be lessened by selecting
the noise reduction. As the level of gain changes, the background noise in the low
light level decreases automatically.
2. Please use the UP and DOWN buttons to 2DNR & 3DNR on the MAIN MENU and
press the ENTER button to do further setups.
3. Please select the mode you would like to set by pressing the UP and DOWN buttons.
*2DNR
•ON:When the 2DNR is set to ON, there’s a submenu available for level adjustment,
ranged from 1 to 4. The higher the level, the more noise can be reduced but sharpness
will decrease.
•OFF: When the 2DNR is set to OFF. Noise will not be reduced.
** 2DNR & 3 DNR **
2DNR ON<┘
3DNR ON<┘
RETURN EXIT
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘
** 2DNR**
LEVEL 3
RETURN EXIT
Sub-Menu under the 2DNR mode
Sub-Menu under 2DNR & 3DNR mode.
** 2DNR & 3 DNR **
2DNR ON<┘
3DNR ON<┘
RETURN EXIT
Sub-Menu under 2DNR & 3DNR mode.

Copyright © 2010. All Rights Reserved.
www.okinausa.com 15 REV122010-V17
*3DNR
•ON:When the 3DNR is set to ON, there’s a submenu available for level adjustment,
ranged from 0 to 15. The higher the level, the more noise can be reduced but moving
objects be blurred in low illumination condition.
•OFF: When the 3DNR is set to OFF. Noise will not be reduced.
**3DNR**
LEVEL 3
RETURN EXIT
Sub-Menu under the 3DNR mode

Copyright © 2010. All Rights Reserved.
www.okinausa.com 16 REV122010-V17
4.6 DAY/NIGHT
The camera can be set in Color or B/W mode in the Day/Night function.
1. Please use the UP and DOWN buttons to DAY/NIGHT on the MAIN MENU and
press the ENTER button to enter.
2. Please select the desired item and press LEFT and RIGHT buttons to adjust the
settings.
*COLOR
The COLOR / DAY mode.
*B&W
The BLACK & WHITE / NIGHT mode.
*AUTO
The camera will switch to DAY/Color mode or NIGHT/B&W mode according to the
setvalue.
•LIVE LEVEL: This indicates the current light level.
•DAY
Æ NIGHT: When the camera detects the current light level is lower than the
set value, it’ll switch from DAY mode to NIGHT mode. Settings
can be set from 6 to 32.
** MAIN MENU **
LENS
AGC
WDR
WHITE BALANCE
2DNR & 3DNR
DAY / NIGHT
SHUTTER
IMAGE
EFFECT
SYSTEM
EXIT
SET<┘
AUTO
WDR<┘
ATW
SET<┘
COLOR
MANUAL<┘
SET<┘
SET<┘
SET<┘
There’re 5 modes under this function: COLOR,
B&W, AUTO, EXTERNAL, SCHEDULE.
Sub-Menu under the DAY / NIGHT AUTO mode
** DAY/NIGHT AUTO **
LIVE LEVEL
DAY->NIGHT
NIGHT->DAY
DELAY TIME
NIGHT OUTPUT
BURST
EXIT
20
3
8
5
5V
ON