Okina SSD4-742AI-B Quick start guide

SHD4-755AI_SSD4-742AI Rev11/2007
SHD4-755AI-B(W)
SSD4-742AI-B(W)
Operational Manual
AVAI Dome Series Color Camera
1/3” Sony Super HAD CCD
550 TV Lines SHD4-755AI
420 TV Lines SSD4-742AI
2.9mm~10.0mm Aspherical Auto Iris IR Lens
(Made in Japan)
12V DC
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may
damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could
damage the camera.
3. Requires a proper operating environment
This camera is designed for indoor use. The allowable temperature range
for operation of this camera is between -10C ~ 50C and the allowable
humidity is 85%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before lens
installation or whenever the lens is changed. Cleaning should be done by
using a chamois, a very fine soft cloth, lens tissue, or cotton tipped
applicator and ethanol to carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range. (Camera
must meet the specifications). Camera must be connected to a surge
protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire or
electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been exposed to rain or water.
d. If the video product has been dropped or the cabinet has been
damaged.
e. When the video product exhibits a distinct change in
performance.
OKINA USA Products are covered under warranty for one year from the
date of purchase. The warranty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any
information regarding when and where the product was purchased. We
have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not
described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.
Model SHD4-755AI SSD4-742AI
Image Sensor 1/3” Sony Super HAD CCD
DSP Sony HQ1 Sony
Number of Total
Pixels NTSC: 811(H) x 508(V) PAL: 795(H) x 596(V) NTSC: 537(H) x 505(V) PAL: 537(H) x 597(V)
Video Output 1.0Vp-p Composite/75 Ohm
Resolution 550 TV Lines 420 TV Lines
Minimum
Illumination 0.25 Lux @ F1.2 0.15 Lux @ F1.2
Signal to Noise Ratio More than 50dB
(AGC OFF) More than 48dB (AGC OFF)
Synchronizing System Internal
Electronic Shutter
Speed Mode ON/OFF Switchable
Back Light
Compensation ON/OFF Switchable
Auto Gain Control ON/OFF Switchable
Flickerless ON/OFF Switchable
DC Level The VR for adjusting the IRIS level of
Auto Iris Lens
White Balance AWB 2500°K ~ 9200°K
Lead Free YES N/A
Lens 2.9mm~10.0mm Aspherical Auto Iris IR Lens
Power Supply 12V DC / 170mA 12V DC/150mA
Power Consumption 2.0W 1.8W
Operation
Temperature -10°C ~+50°C
Storage Temperature -20°C ~ +60°C
Storage Humidity Maximum 85%RH
Weight 300g
Dimensions 118mm(D) × 88mm(H)
FEATURES SPECIFICATIONS
Optional: MB-6D
Wall Mount Bracket
DIMENSIONS
(
Unit: mm
)
Please read the Operational Manual
before attemptin
g
to use this product.
CAUTIONS
WARRANTY

SHD4-755AI_SSD4-742AI Rev07/2007
1. FAR / NEAR
2. WIDE / TELE
3. DC LEVEL
The VR for adjusting the IRIS level of Auto Iris Lens
4. SWITCHES
(1). AES/OFF
AES: Automatic Electronic Shutter. The range of shutter speed
from 1/60sec. (1/50sec.) to 1/100,000 sec.. This mode is
employed for using a manual iris lens.
OFF:AESOFF.Theshutterspeedis1/60sec.
(1/50sec.).
When an auto iris lens is applied, AES should
beoff.
(2).BLC/OFF
BLC:BacklightCompensation.Whentheobjectisdarkbystrong
light (sunlight etc….) as (Fig.2-1), please turn on BLC.
OFF:BLCOFF.
(3).AGC/OFF
AGC: Automatic Gain Control. The level of gain
Variesfrom0to26dB.
OFF:AGCOFF.Thelevelofgainisfixedat0dB.
(4).FL/NOM
FL: Flickerless. In FL mode, the shutter speed is 1/100sec. (NTSC
system) / 1/120sec. (PAL ).
IfchooseFLmode,[AES]switchshouldbeoff.
NOM:Normalposition.
Drill 20mm(3/4") hole on the ceiling as installation template. (see Fig.1).
Fix the mounting plate onto the ceiling as installation template shown holes
position. (see Fig.2).
Fix the dome camera body onto the mounting plate. (see Fig.3).
The on bottom of dome camera body should be put in
the same way on mounting plate then turn right to make sure it is fixed
properly.
Adjust PAN/TILT position and FAR/NEAR &
WIDE/TELE bar to get the mounting picture. (see Fig.4).
Put the cover on to finish the installation. (see Fig.5).
One (1) SHD4-755AI-B, SHD4-755AI-W, SSD4-742AI-B or
SSD4-742AI-W Camera with video/power cable
One (1) Ceiling Top Plate
Five (5) Screws
One (1) Operational Manual
NOMENCLATURES AND FUNCTIONS
①②③④
CAMERA MOUNTING
PACKAGE CON
T
ENTS