Okina SIRZ36-754LP User manual

SIRZ36-754LP
36x License Plate Zoom Camera with IR Kit
Thanks for purchasing our product. Before operating the unit, please read the instructions
carefully and keep this manual for future reference.
SZ36-7540
36x Zoom Camera HI11-TKHBL 11 IR Housing & Bracket

Copyright 2010. All Rights Reserved.
www.okinausa.com - 2 - REV122010-V17
Safety Warnings
 1. Read manual carefully before installing the unit.
Please read this manual first for correct installation and operation.
 2. Never install the camera on a ceiling that cannot hold its weight.
The product may fall down and cause damages.
 3. Never install the camera near electric or magnetic fields.
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices would distort the
video image.
 4. Never install or use the camera in areas exposed to water, oil or gas.
The water, oil or gas may result in operation failure, electric shock or fire. Do not use this
unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, near a swimming pool, in an unprotected outdoor installation, or any area
which is classified as a wet location.

5. Never face the camera toward the sun.
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
 6. Power Cord Protection.
Touching the wet power cord with hands or touching the power cord with wet hands may
result in electric shock. Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, playing particular
attention to cords and plugs, convenience receptacles, and the point where they exit
from the appliance.
 7. Attachments
Do not use attachment not recommended by the product manufacturer as they may
cause hazards.
 8. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock,
Never spill liquid of any kind onto the product.
 9. Do not operate the camera in environments where the temperature, humidity or
power source is beyond the specified ones.
Use the camera in suitable environments where the temperature is within -10°C~ 50°C
and humidity below 90%. The input power source is 12V DC.

Copyright 2010. All Rights Reserved.
www.okinausa.com - 3 - REV122010-V17
 10. Cleaning
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
 11. Never disassemble the camera nor put impurities in it.
Disassembly or impurities may result in trouble or fire.

12. Stop using when the product emits smoke or abnormal heat.
 13. Servicing
Do not attempt to repair this unit yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
 14. Retain Instructions
The safety and operating instructions should be retained for future reference.
Warranty
OKINA USA products are covered under warranty for one year from the date of purchase. The
warranty will automatically be voided if any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any information regarding when
and where the product was purchased. We have no other way to verify the purchase record
without the serial number on the camera sticker; therefore, it should not be removed.
2. Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not described in this manual, the
warranty will be voided immediately. It is the customer’s responsibility to keep the camera in good
condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with. Cutting or modifying of the
cables will result in termination of the warranty.
Notice:
The information in this manual was current when published. The manufacturer
reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.

Copyright 2010. All Rights Reserved.
www.okinausa.com - 4 - REV122010-V17
Table of Contents
1 Product Overview……….………………..………………………………..…………….…..4
1.1 Main Features.…..…………..………………………………………………………....4
1.2 Content List……………………………………………………………………….…….4
1.3 Specifications……………..……….………………………………………………..….5
2 Dimension………………………………………………………………………………………6
2.1 Dimension…………….……………………………………………………………………
2.2 Descriptions…………………………………………………………………………………
3 Camera Setup Operations……………………………………………………………………6
3.1 Menu Tree……………………………………………………….…………….…....6
3.2 Main Menu…………………………...………………………………………………….6
3.3 Submenus of the Main Menu…………………………………………………………
3.3.1 SYSTEM……………………………………………………………………………..7
3.3.2 DISPLAY……………………………………………………………………………..8
3.3.3 PRESET……………………………………………………………………………..9
3.3.4 CAMERA…………………………………………………………………………...10
3.3.4.1 CAMERA – LENS………………………………………………………..11
3.3.4.2 CAMERA - IMAGE………….........................................................…..13
3.3.5 ALARM………..........................................................................................…..15
3.3.6 REBOOT.................................................................................................……..
3.3.7 Control via RS-485..............................................................................................
3.3.8 EXIT……...........................................................................................................
4 Housing & Bracket External Power Input Connection…………….……..................
5 Bracket Installation………………………………………………………………...............
5
5
5
6
8
8
9
12
12
13
13
14
15
16
17
17
20
23
23
24
25
25
26

Copyright 2010. All Rights Reserved.
www.okinausa.com - 5 - REV122010-V17
1. Product Overview
SIRZ36-754LP is an integration of a powerful 36x License Plate Zoom Camera, SZ36-7540, plus
an 11 IR Housing and Bracket, HI11-TKHBL. The camera is built with 1/4" Sony Exview HAD
CCD. Featured with 36x optical auto focus, this camera reproduces sharp and clear images
whether zooming-in or zooming-out.
1.1a Main Features for SZ36-7540 Camera:
1/4" Sony Exview HAD CCD, Sony HQ-1 DSP
36x Optical Auto Focus / Auto Iris Zoom Lens
Color: 540 TVL; B&W: 560 TVL
0.7 Lux @ F1.6 (30 IRE)
Multi-language OSD Setting Menu
Mechanical IR Cut Filter (ICR) / Infrared Compensation
Auto / Ext / Schedule Day & Night Mode
Privacy Zone Masking / Alarm Function
Timer Clock; RS485 Interface (Pelco-D, Pelco P)
12V DC, 4.5W
1.1b Main Features for HI11-TKHBL IR Housing & Bracket:
11 Super Power IR LED, 6pc x 25° / 5pc x 45°
IR Distance up to 395ft / 120m 
User Adjustable IR LED Intensity (VR), Factory Default 80% 
Fully-Cable Managed Bracket
Uses professional rust-proof stainless steel screws
IP66 Rating; Heater & Blower
24V AC, 60VA, Power Ready Plug for 12V DC Camera
See page 7 for details.
1.2 Content List
One (1) SIRZ36-754LP camera with IR housing & bracket
One (1) Main Accessories Pack
Three (3) Rust-proof Stainless Steel Wall Screws
Three (3) Rust-proof Stainless Steel Mounting Screws
Three (3) Stainless Steel Washers
Three (3) Plastic Washers
One (1) Allen Wrench
One (1) Secondary Accessories Pack
Three (3) Screw-on Connectors
One (1) Rubber Pad
One (1) Rust-proof Stainless Steel Camera Screw
One (1) Plastic Washer
One (1) User’s manual
*For any returns, please include all components listed above with original packaging in Resalable Condition.
There is Absolutely No Returns if any component is missing/damaged or if any cable is cut/tampered with.

Copyright 2010. All Rights Reserved.
www.okinausa.com - 6 - REV122010-V17
1.3 Specifications
Kit P.I.C. L-812
Kit
Model SIRZ36-754LP SIRZ36-754LPP
TV System NTSC PAL
Dimension 16.07.87”(L) x 4.33”(W) x 4.53”(H) / 200mm(L) x 110mm(W) x
115mm(H)
Weight 8.23 lbs / 3730g (w/out bracket) ; 12.26 lbs / 5560g (with bracket)
Camera
Model SZ36-7540 SZ36-7540P
TV System NTSC PAL
Image Sensor 1/4 Sony Exview HAD CCD
Total Pixels 410,000 Pixels 470,000 Pixels
Resolution ; DSP Color: 540 TVL, B&W: 560 TVL ; SONY HQ-1
Minimum Illumination Color: 0.7 Lux @ F1.6 (30 IRE), B&W: 0.1 Lux @ F1.6 (30 IRE)
Video Output 1.0Vp-p Composite, 75Ω; Y/C
Signal to Noise Ratio More than 50dB
Mechanical IR Cut Filter
(ICR) IR cut filter removable, Lux level adjustable, 12 steps
Day & Night Mode Color / B&W / Auto / External / Schedule
Synchronization System INTERNAL / EXTERNAL (V-Lock)
Automatic Electronic
Shutter
1/60 Sec., 1/100 Sec., 1/150 Sec., 1/200 Sec., 1/250 Sec., 1/300 Sec.,
1/350 Sec., 1/400 Sec., 1/450 Sec., 1/500 Sec., 1/600 Sec., 1/700
Sec., 1/800 Sec., 1/900 Sec., 1/1000 Sec., 1/1300 Sec., 1/1700 Sec.,
1/2000 Sec., 1/2500 Sec., 1/3200 Sec., 1/4000 Sec., 21Steps
White Balance ATW / Auto / One Push / Manual / 3200K / 6300K
Back Light Compensation ON / OFF
Flickerless ON / OFF
Auto Gain Control Auto / Manual (-3 to 28dB, 16x2dB steps)
Language English, Traditional Chinese, Simplified Chinese, Japanese
Picture Effects Negative / Mirror / B&W
Privacy Zone Masking ON / OFF (8 Zones)
Camera Control Interface PELCO P / PELCO D
Alarm Function Alarm In, Alarm Out
Timer Clock YY/MM/DD
Focusing System Real time AF/ One push AF/ Manual / Infrared Compensation
Min. Working Distance 35mm (Wide end) to 1,500mm (Tele end)
Angle of View H: 57.8o (Wide) ~1.7 o (Tele) / V: 43.7o (Wide) ~1.3 o (Tele)
Lens 36x optical zoom f3.4mm(Wide)~122.4mm(Tele), F1.6 to F4.5
Power Input ; Consumption 12V DC +10% ; 4.5W (Motor Inactive), 5.8W (Motor Active)
Operating Temperature ;
Humidity 14°F~122°F / -10°C~+50°C ; 80% RH Max.
Storage Temperature ;
Humidity -4°F~140°F / -20°C~+60°C ; 20%~90% RH
Dimensions 2.28”(W) x 2.42”(H) x 4.33”(L) / 57.8(W)×61.6(H)×110(L) mm
Weight 0.51 lbs / 230g

Copyright 2010. All Rights Reserved.
www.okinausa.com - 7 - REV122010-V17
IR
Housing
& Bracket
Model HI11-TKHBL
LED Quantity & Beam Angle 11 Super Power IR LEDs, 6pc x 25° / 5pc x 45°
IR Wave Length & Distance 850nm ; 395ft / 120m 
IR Light On / Off Auto Light Sensor Control
Heater Control 18C / 64F (on); 28C / 82F (off)
Blower Control 35C / 95F (on); 25C / 77F (off)
IP Rating IP66
Temper Glass Thickness 4mm
Mounting Bracket Full-Cable Management
Construction Die-Cast Aluminum Alloy
Coating Ivory Powder Stove
Required Power /
Transformer * 24V AC (+/-10%), 60VA
Power Consumption 16.0W
Dimension 16.07.87”(L) x 4.33”(W) x 4.53”(H) / 200mm(L) x 110mm(W) x
115mm(H)
Camera Space 16.73”(L) x 6.30”(W) x 6.50”(H) / 425mm(L) x 160mm(W) x 165mm(H)
Weight 7.72 lbs / 3500g (w/out bracket) ; 11.75 lbs / 5330g (with bracket)
* Power supply / transformer not included
NOTE 1: IR light distances are entirely dependant upon environmental site conditions and the location at which the unit
is situated. The type of camera being used is also very important.
NOTE 2: Factory default for the IR LED activation level is 80%. If there is not enough IR light, adjust the VR level to
maximum 100%. Please see #17 in the Part Description section on page 1.

Copyright 2010. All Rights Reserved.
www.okinausa.com 8 REV122010-V17
比例
+
VRI
GND
485+
DNO
DNI
485-
2. Dimension
2.1a Camera Dimension
2.1b Housing & Bracket Dimension
Bracket (on left):
Max Load: 3500g
Material: Die-cast aluminum alloy with light ivory
powder coated and stove finish
Scan Angle: 180°
Tilt Angle: 90°
Net Weight: 900g
Fixing: 3 Screws with bushings

Copyright 2010. All Rights Reserved.
www.okinausa.com 9 REV122010-V17
+
VRI
GND
485+
DNO
DNI
485-
2.2a Camera Descriptions
Video Connector
This is an output for BNC connection to a video monitor, etc (75Ω).
Setting Button
SETUP button
UP & DOWN button
LEFT & RIGHT button
Communication Connector
1. RS485+
2. RS485-
3. Day & Night Output
4. Day & Night External Input
5. V Lock Pulse Input
6. Ground
S-Video output terminal
Separate Y(brightness) and C (Color) signal are outputs from this terminal to obtain better
video quality at a video monitor.
1. C signal: 0.3V (p-p), 75Ω, unbalance
2. Y signal: 1.0V (p-p), 75Ω, unbalance, negative synchronizing
3. C signal Ground
4. Y signal Ground
Power Input Indicator Light
When the camera is connected to a power source, the indicator light will be on.
Power Input Terminal
Connect the power input of 12V DC.
RS-485 Terminal Resistor Switch
Set the first and the last equipments terminal resistor as ON. As for the rest parallel
connection equipment in the middle set as OFF to keep the best transmitted status.

Copyright 2010. All Rights Reserved.
www.okinausa.com 10 REV122010-V17
2.2b Housing & Bracket Descriptions

Copyright 2010. All Rights Reserved.
www.okinausa.com 11 REV122010-V17
1. Lens Cap with Heater
2. Temper Glass
3. IR LED: 7pcs or 11pcs Super Power IR LED with Refractor
4. IR Board and IR Board Bracket
5. Universal IR Control Circuit Board: When the IR light turns on, it automatically adjusts the color
to monochromatic through the universal IR control circuit.
6. Camera Bracket
7. Power Supply Unit: 24V AC input, 60VA
8. Blower and Blower Bracket
9. Thermostat Switch
10. Video Input BNC Male Connector: Connect to camera
11. Video Out BNC Female Connector: Connect to monitor
12. Terminal Board
13. Fuse Holder: With 250V / 3.15A fuse
14. AC IN Terminal block: 24V AC external power input
15. OUTPUT_1 Terminal block: Plug and fix the power cable of camera
16. OUTPUT_2 Terminal block: To power supply unit
17. VR: Adjust VR to set Infrared LED activation level
Factory default 80% -- If there is not enough IR light, adjust the level to maximum 100% 
18. Thermostat Switch: Turns on at 35C / 95F and turns off at 25C / 77F for Blower
19. Ground wire: To top cover
20. 12V DC Power-in jack: To camera / center+, outer-
When using a camera which requires a 24V AC power input, please run a separate power
line to the camera
21. Flying Bare Lead Wire: When the wire is not in use, cover it with the screw-on connector or
tape the tip with tape to prevent damages caused by the bare lead wire.

Copyright 2010. All Rights Reserved.
www.okinausa.com 12 REV122010-V17
3. Camera Setup Operations
3.1 Menu Tree
MAIN MENU
SYSTEM
DISPLAY
PRESET
CAMERA
ALARM
REBOOT
EXIT
LANGUAGE CAMER
A
TITLE BAUD RATE PROTOCOL FIRMWARE RESTORECAMERA ID
CARMERA ID CAMERA
TITLE
PRESET
TITLE DATE/TIME ALARMZOOM RATIO
PRESET NO. POSI SAVE DELETE TITLE PAUSE TIME
LENS IMAGE
FOCUS
IRIS
BRIGHTNESS
ZOOM SPD
FOCUS SPD
DAY/NIGHT
NIGHT LIGHT
EXPOSURE
MODE
WHITE
SHARPNESS
BACKLIGHT
FLC
AGC
SYNC
MIRROR
POS./NEG.
PRIVACY
MASK
IN SWITCH IN MODE OUT SWITCH OUT TIME
ALARM MESSAGE
WHITE BALANCE

Copyright 2010. All Rights Reserved.
www.okinausa.com 13 REV122010-V17
3.2 Main Menu
MAIN MENU
SYSTEM
DISPLAY
PRESET
CAMERA
ALARM
REBOOT
SET 
SET 
SET 
SET 
SET 
STARTUP 
EXIT
3.3 Submenus of the MAIN MENU
There’re several submenus of the main menu: SYSTEM, DISPLAY, PRESET, CAMERA,
ALARM, and REBOOT.
Return to previous page
Select RETURN and press the SET button to return to previous page.
Close the menu screen
To close the menu screen, use the buttons to select EXIT and press the SET button.
Enter the engineering menu
Press the RIGHT button for 3 seconds to enter the engineering menu to select the suitable camera type.
Selections are Camera, Car Plate License Camera, and Module Camera. When the Module Camera is
selected, values of CAMERA ID, BAUD RATE, and PROTOCOL can not be changed.

Copyright 2010. All Rights Reserved.
www.okinausa.com 14 REV122010-V17
3.3.1-SYSTEM
I. LANGUAGE:
Set language preference. Selections are ENGLISH TRADITIONAL CHINESE
SIMPLIFIED CHINESE JAPANESE
II. CAMERA ID:
Camera ID can be set in here. Only numbers 1-1024 can be used.
III. CAMERA TITLE:
Numbers, letters and symbols can be used for naming the camera title.
*Use direction buttons to select the desired character.
*Press SET button to confirm each selection.
*Use the direction buttons to OK to confirm the setting.
*Use the direction buttons to CANCEL to abort the setting.
*Select POSI to change the position of the shown camera title.
*Select SPACE when a blank / a space is needed.
*Select BACKSPACE to clear the precedent character.
IV. BAUD RATE:
Baud Rates can be set here. 2400 4800 9600 19200 38400
V. PROTOCOL:
Select the protocol here. There’re 2 types PELCO D PELCO P
VI. FIRMWARE:
Please refer to the actual firmware version.
VII. RESTORE:
Choose CANCEL to exit; once the CONTINUE is selected, all the settings will be
restored to the default settings. There’re no default settings for Camera Type,
CAMERA ID, BAUD RATE, PROTOCOL and Language; thus, these settings will
stay the same even the CONTINUE is selected.
LANGUAGE ENGLISH TRADITIONAL CHINESE SIMPLIFIED CHINESE JAPANESE
CAMERA ID 1~1024
CAMERATITLE SET
BAUD RATE
2400 4800 9600 19200 38400
PROTOCOL PELCO D PELCO P
FIRMWARE XX.XX
RESTORE SET

CANCEL

CONTINUE
0123456789
ABCDEFGHI J KLM
NOPQRSTUVWXYZ
a b c d e f g h i j k l m
nopqrst uvwxyz
. , : ‘ “ / # * = ( ) < >
- - - - - - - - - - - - - - - -
SPACE BACKSPACE
POSI COPY
OK CANCEL

Copyright 2010. All Rights Reserved.
www.okinausa.com 15 REV122010-V17
3.3.2-DISPLAY
I.
CAMERA ID:
Select ON to show the Camera ID on the screen; select OFF to hide the Camera
ID from the screen.
II.
CAMERA TITLE:
Select ON to show the Camera Title on the screen; select OFF to hide the
Camera Title from the screen.
III.
PRESET TITLE:
Select ON to show the Preset Title on the screen; select OFF to hide the Preset
Title from the screen.
IV.
DATE/TIME:
HH: Hour, MM: Minute, SS: Second, YY: Year, MM: Month, DD: Date.
*Select ON/OFF to show/hide the Date/Time on the screen.
DATE/TIME Adjust:
*When ON is selected, Date/Time can be adjusted.
*Press SET BUTTON to set up.
*Use RIGHT BUTTON to increase the number and LEFT BUTTON to decrease.
*Press the SET BUTTON to confirm each adjusted number.
FORMAT Adjust:
*The Date/Time Format can further be arranged.
YY：MM：DD MM：DD：YY DD：
MM：YY
V.
ZOOM RATIO:
Select ON to show the Zoom Ratio on the screen; select OFF to hide the Zoom
Ratio from the screen.
VI.
ALARM MESSAGE:
Select ON to show the Alarm Message on the screen; select OFF to hide the
Alarm Message from the screen.
CAMERA ID OFF ON
CAMERATITLE OFF ON
PRESET TITLE
OFF ON
DATE/TIME
OFF ON 
ZOOM RATIO
OFF ON
ALARM MESSAGE OFF ON
DATE / TIME
TIME HH：MM：SS
DATE YY：MM：DD
FORMAT YY：MM：DD MM：DD：YY DD：MM：YY
RETURN EXIT

Copyright 2010. All Rights Reserved.
www.okinausa.com 16 REV122010-V17
3.3.3-PRESET
I.
PRESET NO.:
Select the to-be-set/desired PRESET NO from 1-256.
II. POSI: U ZOOM D/L FOCUS R
Press SET while the POSI is highlighted to setup the position. Use UP/DOWN
BUTTON to adjust ZOOM and LEFT/RIGHT BUTTON to adjust the FOUCS.
III.
SAVE: Select SETand press the SET BUTTON to save the settings.
IV.
DELETE: Select ABOVE or ALL to delete the setting above or to delete every
preset settings.
V.
TITLE:
Numbers, letters and symbols can be used for naming the camera title.
*Use direction buttons to select the desired character.
*Press SET button to confirm each selection.
*Use the direction buttons to OK to confirm the setting.
*Use the direction buttons to CANCEL to abort the setting.
*Select POSI to change the position of the shown camera title.
*Select SPACE when a blank / a space is needed.
*Select BACKSPACE to clear the precedent character.
VI.
PAUSE TIME:
Pause time can be chosen from 0 to 255 seconds.
PRESET NO. 1-256
POSI SET
SAVE SET
OK
DELETE ABOVE ALL
TITLE SET
PAUSE TIME
0-255
U ZOOM D/LFOCUS R
PRESS ENTER CONFIRM
0123456789
ABCDEFGHI J KLM
NOPQRSTUVWXYZ
a b c d e f g h i j k l m
nopqrst uvwxyz
. , : ‘ “ / # * = ( ) < >
- - - - - - - - - - - - - - - -
SPACE BACKSPACE
POSI COPY
OK CANCEL

Copyright 2010. All Rights Reserved.
www.okinausa.com 17 REV122010-V17
3.3.4-CAMERA
3.3.4.1-CAMERA-LENS
LENS SET

 FOCUS REAL TIME AF ONE PUSH MANUAL
 IRIS AUTO MANUAL
 BRIGHTNESS 1-15
 ZOOM SPD 1-15
 FOCUS SPD 1-15
 DAY / NIGHT COLORB&WAUTOEXT SCHEDULE
 NIGHT LIGHT NORMAL INFRARED
COLOR
B&W
AUTO

LEVEL 1-10
DLY TIME 1-10 SEC
OUTPUT
EXTERNAL

DAY / NIGHT IN L LEVEL H LEVEL
SCHEDULE

DAY / NIGHT HH：MM
NIGHT / DAY HH：MM

Copyright 2010. All Rights Reserved.
www.okinausa.com 18 REV122010-V17
I.
LENS: Settings concerning Lens can be set in here.
i.
FOCUS:
REAL TIME AF:
Select REAL TIME AF to detect the ambiance light and to adjust the focus
automatically.
ONE PUSH:
When the zoom is changed with the TELE or the WIDE buttons, it becomes
AF Mode. Then, it stops.
MANUAL:
Select MANUAL to adjust the focus by adding or subtracting the shown
setting.
ii.
IRIS:
MANUAL: Select MANUAL adjust the IRIS manually.
AUTO: When AUTO is selected, the IRIS will be adjusted automatically.
iii.
BRIGHTNESS:
There’re 1-15 levels: the bigger the number, the brighter the images. But if
the IRIS has set to be manual, this function will be disabled.
iv.
ZOOM SPD:
There’re 1-15 levels: the bigger the number, the faster the zoom changing
speed will be.
v.
FOCUS SPD:
There’re 1-15 levels: when under the manual mode, the bigger the number,
the faster the focus changing speed will be. However, under REAL TIME
AF and ONE PUSH Modes, the FOCUS SPD is fixed and can not be
adjusted.
vi.
DAY/NIGHT:
COLOR: The COLOR mode.
B&W: The BLACK & WHITE mode.
AUTO: When AUTO is selected, it will detect the ambient light to change
from DAY/COLOR to NIGHT/B&W and vice versa.
LEVEL: Select brightness of illumination about changing the day/night mode.
The bigger the number, the brighter the images.
DELAY TIME: can be chosen from 1 to 10 seconds to delay the
switching time (from DAY/Color to NIGHT/B&W time and vise visa.)
OUTPUT: Select output level. D&N OUT: It’s the PIN 3 external control
connector.
(HIGH: 5V; LOW: GND)
OUTPUT
D&N OUT
SYSTEM
L LEVEL H LEVEL
COLOR HIGH LOW
B&W LOW HIGH

Copyright 2010. All Rights Reserved.
www.okinausa.com 19 REV122010-V17
EXTERNAL: Use the external signal to switch COLOR/B&W.
INPUT: Select input level. D&N IN: It’s the PIN 4 external control connector.
(HIGH:OPENor5V;LOW:GND)
SCHEDULE: When SCHEDULE is selected, timing can be set to switch
Day/Night Mode.
DAY/NIGHT: set the timing to switch from DAY/COLOR to NIGHT/B&W.
NIGHT/DAY: set the timing to switch from NIGHT/B&W to DAY/COLOR.
vii.
NIGHT LIGHT:
When IR LED is in use, select INFRARED. When regular illuminator is in
use, select NORMAL.
INPUT
SYSTEM
D&N IN
L LEVEL H LEVEL
HIGH COLOR B&W
LOW B&W COLOR

Copyright 2010. All Rights Reserved.
www.okinausa.com 20 REV122010-V17
3.3.4.2-CAMERA-IMAGE
IMAGE SET


EXPOSURE MODE MANUAL  AUTO 
 WHITE BALANCE ATW AUTO MWB ONE PUSH
3200K 6300K
 SHARPNESS 0-15
 BACKLIGHT OFF BLC 

FLC OFF ON
 AGC MANUAL  AUTO
 SYNC INT LL 
 MIRROR OFF ON
 POS. / NEG. OFF ON
 PRIVACY MASK SET
OFF ON
AUTO--SHUT SPD
1/250 1/500
1/1000 1/2000
1/4000 1/10000
1/100000
MANUAL-SHUT SPD
1/60 Sec. 1/100 Sec. 1/150 Sec.,
1/200 Sec. 1/250 Sec. 1/300 Sec.,
1/350 Sec. 1/400 Sec. 1/450 Sec.,
1/500 Sec. 1/600 Sec. 1/700 Sec.,
1/800 Sec.1/900 Sec. 1/1000 Sec.,
1/1300Sec.1/1700Sec.1/2000Sec.,
1/2500Sec.1/3200Sec.1/4000Sec.
BLC
1~16 Levels
ON
 AREA SEL 01-08
 AREA MODE
COLOR
 GREEN  ORANGE  BLACK  WHITE
 GRAY  BLUE  RED  PURPLE