Olivetti d-Color MF2001 User manual

INSTALLATION MANUAL
Multifunction Color
d-Color MF2001
d-Color MF2501
Code: Y112990-2

PUBLICATION ISSUED BY:
Olivetti S.p.A.
Gruppo Telecom Italia
Via Jervis, 77 - 10015 Ivrea (TO)
Copyright © 2011 Olivetti
All rights reserved

2KZ/2K0
1-1
1-2 Installation
1-1 Installation environment
1. Temperature: 10 to 32.5°C/50 to 90.5°F
2. Humidity: 15 to 80% RH
3. Power supply: 120 V AC, 12.0 A
220 - 240 V AC, 6.5 A
4. Power supply frequency: 50 Hz ±2%/60 Hz ±2%
5. Installation location
Avoid direct sunlight or bright lighting. Ensure that the photoconductor will not be exposed to direct sun-
light or other strong light when removing paper jams.
Avoid locations subject to high temperature and high humidity or low temperature and low humidity; an
abrupt change in the environmental temperature; and cool or hot, direct air.
Avoid places subject to dust and vibrations.
Choose a surface capable of supporting the weight of the machine.
Place the machine on a level surface (maximum allowance inclination: 1°).
Avoid air-borne substances that may adversely affect the machine or degrade the photoconductor, such
as mercury, acidic of alkaline vapors, inorganic gasses, NOx, SOx gases and chlorine-based organic sol-
vents.
Select a well-ventilated location.
6. Allow sufficient access for proper operation and maintenance of the machine.
Figure 1-1
100 mm
3 15/16”
100 mm
3 15/16” 450 mm
17 11/16”
1000 mm
39 3/8”
500 mm
19 11/16”
Y112990-2 Sevice Manual

Service Manual 1-2 Y112990-2
1-2 Unpacking and installation
(1) Installation procedure
Unpack
Install the optional paper feeder
Release the scanner lock lever
Load paper
Remove the tapes and spacer
Start
Install the toner container
Attaching the language label
(Excluding 240V AC)
Make test copies
Switch the cassette heater switch
Install the expansion memory (option)
Connect the power cord
Exit maintenance mode
Print out the user setting list
Install the other optional devices
Installing toner
Output an own-status report
(maintenance item U000)
Completion of the machine installation
Install the job separator tray

2KZ/2K0
1-3
l
Figure 1-2
*1 Excluding 230V AC model
Place the machine on a level surface.
1
22
24
2
3
4
524
6
7
8
9
10
11
12
22
22
22
21
13 14
15
18
19
20
16
17
23
25
26
27
28
Unpacking
1. Bottom case
2. Bottom pad R
3. Bottom pad L
4. Machine cover
5. Machine
6. Inner case R
7. Inner case L
8. Spacer A
9. Plastic bag (540 × 950)
10. Outer case
11. Upper pad R
12. Upper pad L
13. Toner container /YCM
14. Toner container /K
15. Plastic bag (250 × 650)
16. CD-ROM *1
17. Installation guide, etc.
18. Plastic bag
19. Job separator tray
20. Plastic bag (400 × 600)
21. Power cord
22. Hinge joints
23. Quick installation guide
24. Reinforcement parts
25. Plastic bag
26. Lower pad
27. Front pad
28. Desiccant
Y112990-2 Sevice Manual

2KZ/2K0
1-4
1. Remove four tapes.
Figure 1-3
2. Open the DP top cover.
3. Slide two DP original width guides and
then remove the pad.
4. Close the DP top cover.
Figure 1-4
Remove the tapes and spacer
Tape Tape
Tape
Tape
DP top cover Pad
DP original width guides
Service Manual 1-2 Y104350-7
Service Manual 1-2 Y112990-2Service Manual 1-2 Y112990-2
Sevice Manual Y112990-2

2KZ/2K0
1-5
5. Open the DP.
6. Remove the protective sheet and paper.
Figure 1-5
7. Remove the paper.
8. Close the DP.
Figure 1-6
DP
Protective sheet
DP
Paper
Y112990-2 Sevice Manual

2KZ/2K0
1-6
9. Remove the tape.
Figure 1-7
10. Peel off two protective sheets.
11. Remove the spacer.
Figure 1-8
Tape
Spacer Protective sheets
Sevice Manual Y112990-2

2KZ/2K0
1-7
1. Gently push the job separator tray into
the machine along the guides.
Figure 1-9
1. Pull the scanner lock lever in the direc-
tion of the arrow. This will unlock the
scanner mechanism.
Figure 1-10
Install the job separator tray
Job separator tray
Right guide
Left guide
Release the scanner lock lever
Scanner
lock lever
Y112990-2 Sevice Manual

2KZ/2K0
1-8
1. Install the optional paper feeder as
required.
Figure 1-11
1. Pressing the paper width adjusting tab
as shown, move the paper width guides
to fit the paper size.
Figure 1-12
Install the optional paper feeder
Paper feeder
Load paper
Cassette
Paper width
adjusting tab
Paper width guides
Sevice Manual Y112990-2

2KZ/2K0
1-9
2. Adjust the paper length guide to fit the
paper size.
Figure 1-13
3. Align the paper so that it is abut with the
right end of the cassette.
4. Insert the cassette size plate.
5. Gently push the cassette back in.
Figure 1-14
Paper length guides
Paper
Cassette
Cassette
size plate
Y112990-2 Sevice Manual

2KZ/2K0
1-10
1. Open the front cover.
2. Hold the toner container vertically and
tap the upper part five times or more.
Turn the toner container upside down
and tap the upper part five times or
more.
Figure 1-15
3. Shake the toner container up and down
five times or more.
Turn the toner container upside down
and shake it five times or more.
Figure 1-16
Install the toner container
Toner container
Toner container
Sevice Manual Y112990-2

2KZ/2K0
1-11
4. Shake the toner container approxi-
mately five or six times in the horizontal
direction to stir toner.
Figure 1-17
5. Gently push the toner container into the
machine.
Push the container all the way into the
machine until it locks in place.
Figure 1-18
Toner container
Toner container
CLICK!
Y112990-2 Sevice Manual

2KZ/2K0
1-12
1. Release the hook and then remove the
switch cover.
2. Turn the cassette heater switch on.
Note: When the cassette heater is
used, it turns it on.
3. Refit the switch cover.
Figure 1-19
1. Install the optional devices (Document
finisher, Fax kit, etc.) as required.
1. Connect the power cord to the connector on the machine.
2. Insert the power plug into the wall outlet.
1. Turn the main power switch on.
The machine automatically starts to feed toner in the developer unit.
Note: When the main power switch is turned on for the first time, it takes about one minute until
entering the state that can be copied.
2. The drive chain is disengaged when toner installation is completed.
Switch the cassette heater switch
Switch cover
Hook
Install the other optional devices
Connect the power cord
Installing toner
Sevice Manual Y112990-2

2KZ/2K0
1-13
1. Enter 000 using the numeric keys and press the start key.
2. Select Maintenance and press the start key to output a list of the current settings of the maintenance
items.
3. Press the stop key.
1. The machine is reactivated by switching the main power switch off and on.
1. Select [Report Print] to print a user setting list.
1. Place an original and make test copies.
1. Attach the corresponding language label as required.
(2) Setting initial copy modes
Factory settings are as follows:
Maintenance
item No. Contents Factory setting
U253 Switching between double and single counts Double count
(A3/Ledger)
U260 Selecting the timing for copy counting Eject
U285 Setting service status page On
U326 Setting the black line cleaning indication On/8
U343 Switching between duplex/simplex copy mode Off
Output an own-status report (maintenance item U000)
Exit maintenance mode
Print out a user setting list
Make test copies
Attaching the language label (Excluding 240V AC)
Installation is completed.
Y112990-2 Sevice Manual

STATODIAGGIORNAMENTO
UPDATINGSTATUS
DATA PAGINE AGGIORNATE PAGINE CODICE
DATE UPDATED PAGES PAGES CODE
03/2010 1aEDIZIONE - 1st EDITION 16 Y112990-2