olympia electronics ΒS-531/1/MAR User manual

Page 1 from 5
SOUNDER WITH BEACON FOR FIRE DETECTION PANEL
GENERAL
This device is Visual Alarm Devices (VAD) for
fire detection panels that offer a strong sound
output and an optical warning with a beacon
and is used on ships. The strong sound and
the optical warning beacon cover many
square metres. It features two inputs (N1, N2)
for the production of two different sounds.
This device can co-operate with any fire
detection panel (BSR-2104/MAR, BSR-
2114/MAR, BS-1632, BS-1634, BS-1636, BS-
636).
Installation and Connection
1. First, remove the retaining screw, place a
flat blade screwdriver in the holes of the
plastic hooks and remove the plastic cover
(Image 1 on page 2).
2. Remove carefully the beacon connector
(Image 2 on page 2).
3. Use the supplied mounting parts to install the
siren’s base at a height of 2.4 metres from
the floor (figure 1 on page 2). Place the
plastic plugs and fasten the screws to the
mounting holes. Attention!! Make sure that
the siren’s base is installed upwards as
shown in figure on page 4.
4. Place the caps and make a hole in the center
using a small screwdriver. Pass through the
caps the cables to connect the device.
5. The (+N1 or the +N2) terminal block is
connected to the (+) output of Alarm-1 or
Alarm-2 of the panel and the (-) of the
terminal block is connected to the (-) output
of Alarm-1 or Alarm-2 of the panel.
Accordingly connect in parallel all the sirens.
(The maximum number of sirens depends on
the type of the panel).
6. To select various sound effects use the
dipswitch 1, 2 and 3 and choose the
diserable sound effect, according to tables 2
and 3 on page 3.
7. For LED effect variation use the dipswitch 4
(Table 1) on page 2. On the last siren of the
line, we must connect in parallel with its
power cables, the terminal resistor that was
removed from the alarm contacts of the
panel.
8. Reinstall the beacon connector (step 2).
Refit the plastic cover until the plastic hooks
are securely attached (step 1) and fasten the
retaining screw (torque 0.6Nm). Attention!!
Make sure that the siren’s cover is installed
in the correct orientation.
9. Test the device after installation.
ΒS-531/1/MAR
ΤΕCHNICAL CHARACTERISTICS
OPERATION VOLTAGE
MAXIMUM CONSUMPTION
MAXIMUM SOUND OUTPUT in1m
ΤYPE OF APPLICATION ENVIRONMENT
MOUNTING
COVERAGE (y)
BEACON
21-28V DC
Τype Α
1 Power LED
Wall
6 m around the siren at an angle of 180°
94dB (sound effect 1)
1.2W
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
TYPICAL WEIGHT
GUARANTEE
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
IP 42C
COVERAGE VOLUME
FLASH RATE
FLASH COLOUR
86.4m³ (max)
1 Hz (Switchable to 0.5 Hz)
Red
o
0 to 60 C
Up to 95%
2 years
230gr.
141 x 141 x 100 mm
CONSTRUCTION MATERIAL Bayblend FR3010, transparent polycarbonate
MOUNTING HEIGHT (x) 2.4m max
COVERAGE VOLUME CODE W-2.4-6
921531009_09_004
Thank you for your trust in our products
Olympia Electronics - European manufacturer
rd
EN 54-3:2001+A1:2002+A2:2006, EN 54-23:2010, EN 50130-4:2011, IEC 60092-504 3 Ed.:2001+Cor1:2011, IEC 60533:1999 Edition 2.0

921531009_09_004
Page 2 from 5
0.1 sec ON 1.9 sec OFF (0.5 Hz)
0.1 sec ON 0.9 sec OFF (1 Hz)
ON
4
ON
4
2
Image 2
Image 3
Image 1
DSW LED effect NOTE!!! After finishi ng the
installa tion, place th e SEAL stic ker
as shown in th e picture.
Figure 1 W -Wall Mounted Device
TABLE 1
TO FIRE
DETECTION
PANEL
W-x-y
D i p s w i t c h
s i r e n a n d
b e a c o n
selections
y
yx
x=2.4m
y=6m VAD
11
1
UP
UP
3 3
3
4
5
4
6
+N1 + N2
1
ON
2 3 4

921531009_09_004
0 91 21
94 22
90 22
87 31
91 29
82 27 92 24
83 27
1
2
3
4
5
6
7
Sound effect
TABLE 2
Tone in accordance to:
Fire Detection Panel connection to +N1
dB mA
11
ONON
22 33
11 11 11 11 11 1
ONON ONON ON ONON ONON ON
22 22 22 22 22 2
33 33 33 33 33 3
11
ONON
22 33
11 11 11 11 11
ONON ONON ON ONON ONON
22 22 22 22 22
33 33 33 33 33
1
ON
2 3
DSW Nr
970Hz continuous BS5839-1:2002 - ‘’evacuate’’ BS5839 Part 1 1988
BS5839-1:2002 - ‘’alert’’ BS5839 Part 1 1988 BS5839-1:2002 - DIN -Tone DIN33404 Part 3 BS5839-1:2002 NEN2575 (Netherlands) ISO8201 High Frequency ISO8201 Low tone - US Temporal Tone LF ISO8201 High tone - US Temporal Tone HF
970Hz (1sec ON - 1 sec OFF) From 1200Hz to 500Hz in 1 sec From 500Hz to 1200Hz in 3.5 sec - 0.5 sec OFF 800Hz - 970Hz alternate at 1Hz Intermittent 2850Hz (0.5 sec ON - 0.5 sec OFF) 970Hz (0.5 sec ON 970 Hz OFF x3 times +1.5 sec OFF) 2850Hz (0.5 sec ON 2850 Hz OFF x3 times +1.5 sec OFF)
TABLE 3
Tone in accordance to:
BS5839-1:2002 - ‘’evacuate’’ BS5839 Part 1 1988 BS5839-1:2002 - ‘’alert’’ BS5839 Part 1 1988 BS5839-1:2002 - DIN -Tone DIN33404 Part 3 BS5839-1:2002 NEN2575 (Netherlands) ISO8201 High Frequency ISO8201 Low tone - US Temporal Tone LF ISO8201 High tone - US Temporal Tone HF
0
91 21
94 22
90 22
87 31
91 29
82 27 92 24
83 27
1
2
3
4
5
6
7
Sound effect
Fire Detection Panel connection to +N2
dB mA
1
ON
2 3
1
ON
2 3
DSW Nr
970Hz continuous 970Hz (1 sec ON - 1 sec OFF) From 1200Hz to 500Hz in 1 sec From 500Hz to 1200Hz in 3.5 sec - 0.5 sec OFF 800Hz - 970Hz alternate at 1Hz Intermittent 2850Hz (0.5 sec ON - 0.5 sec OFF) 970Hz (0.5 sec ON 970 Hz OFF x3 times +1.5 sec OFF) 2850Hz (0.5 sec ON 2850 Hz OFF x3 times +1.5 sec OFF)
Page 3 from 5

921531009_09_004
Page 4 from 5
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd klm old highway Thessaloniki-Katerini,
P.O. 60061 Kolindros, Pieria Greece
www.olympia-electronics.gr
[email protected]

921531009_09_004
Page 5 from 5
Horizontal line parallel with the ceiling
Figure which shows the correct positioning of the base
Wall hole diameter 6mm