Olympia Tools 703-118-101 User manual

Bvsgfdsg
SKU #
1334088
M
od
e
l
#
703
-
118
-
101
USE AND CARE GUIDE
_______________________________________
3300 LUMENS LED FLASHLIGHT

TABLE OF CONTENTS
Safety Information
Warranty
Package Contents
Hardware Included
Operation
Troubleshooting
Care and Cleaning
SAFETY INFORMATION
WARNING: Carefully read and understand the information given in
this manual before beginning the assembly and installation.
Failure to do so could lead to battery leak, explosion, fire, burning
hand/ skin or other damages and injuries which could be
hazardous or even fatal.
WARNING: THIS FLASHLIGHT IS NOT A TOY, not recommended for
use by children.
WARNING: Highly intensive light beam could cause damage to your
eyes. Do not look directly into the flashlight. Do not point LED
flashlight to anyone’s eyes.
WARNING: AVOID EXPOSING BATTERIES TO FIRE OR
EXCESSIVE HEAT, as this may cause leakage or explosion. To
AVOID RISK OF INJURY TO EYES OR SKIN, AVOID
CONTACT WITH ANY MATERIAL LEAKED FROM A BATTERY.
WARNNG: AVOID CONNECT CONTACT POINTS OF THE
BATTERY HOLDER WITH METAL PARTS AND WIRES.
Contact between them could short-circuit the batteries and
generate heat or cause fire or battery leak.
WARNING: Press the push button repeatedly to keep the flashlight
working on the “High” mode continuously could cause the
flashlight surface and batteries inside the flashlight very hot and
burn hand/ skin. Turn the flashlight off and let it cool down to a
comfortable temperature before being held in hand.
WARNING: Do not change batteries when the LED flashlight/
batteries are still hot; change batteries when they have reached a
comfortable temperature in hand.

WARNING: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the flashlight.
WARNING: The flashlight is rated of weather resistance (IPX4). DO
NOT SUBMERSE.
WARNING: Do not use different brands of batteries together. Do not
mix old and new batteries. Do not mix alkaline, carbon zinc or
rechargeable batteries. When replacing batteries, always replace
the whole set. Do not dispose of batteries in fire, batteries may
explode or leak. Recycle or manage as hazardous waste.
NOTICE: If the LED flashlight is used less than once a month, remove
the batteries between uses.
NOTICE: Use only alkaline batteries of a reputable brand.
WARRANTY
If the flashlight has been damaged by leakage of batteries, do not
return the flashlight to Olympia Tools but determine what brand of
battery caused the damage and follow the battery manufacturer’s
instructions about how to make a damage claim.
PACKAGE CONTENTS
Part Description Quantity
A 3300 Lumens Flashlight 1
B Alkaline AA batteries 12
HARDWARE INCLUDED:
Part Description Quantity
A Battery holder 1

OPERATION:
BATTERY INSTALLATION
Install batteries with the correct polarity specified on the battery
holder. Reversely install the batteries will lead to battery contact points
disconnected, this will cause no electric current flow in the circuit and
the LED flashlight does not light.
NOTE: The battery holder is specially designed with reverse-
installation-proof construction. If the LED flashlight does not light
after pressing the push button, check whether the batteries are
installed correctly first; if the problem still exists, see section
“Troubleshooting”.
TURN ON/ OFF THE FLASHLIGHT
Press push button down until it clicks; click again to switch from “High”
mode to “Low” mode; one more click to turn the flashlight off.
NOTE: The LED flashlight modes are predefined as:
“High> Low> Off”.
INSTANT MODE CHANGE
The LED flashlight can change between the “High” and “Low” modes
without going through the whole “High> Low> Off” cycle. See the
operation steps below for details:
Step 1. Turn on the LED flashlight,
Step 2. Press the push button halfway down till see the mode is
changed (Note: No “click” sound during this operation),
Step 3. Release the push button, the LED flashlight is now working on
the other mode.
Repeat Step 2 and Step 3 to activate an Instant Mode Change at any
time.
BEAM ADJUSTMENT
Adjust the LED flashlight light beam from FLOOD TO SPOT, twist the
head of the LED flashlight counterclockwise; adjust the beam from
SPOT TO FLOOD, twist the head of the LED flashlight clockwise.

TROUBLESHOOTING
Minor problems often can be fixed without the help of an electrician.
WARNING: Before doing any work on the LED flashlight, press the
push button to turn off the power.
Problem Possible Cause Corrective Action
The
flashlight
does not
light.
The power is off. Check if the power supply
is on.
Batteries have run down. Replace with reputable
brand alkaline AA
batteries.
Battery/ batteries are
installed reversely.
Install the battery/ batteries
correctly.
Carbon-zinc batteries are
installed.
Use reputable brand
alkaline AA batteries.
Contact point(s) of
batteries or battery holder
are contaminated with dust
or damaged by battery
leakage.
Carefully remove any
damaged batteries and
clean any corrosion on the
contact points.
The LED
flashlight
surface or
batteries
are hot.
Keep the LED flashlight
working on the “High”
mode repeatedly by
pressing the push button
after the flashlight works
on “High” mode couple
minutes. This could cause
excessive heat
accumulation and risk of
burn.
If the flashlight has worked
on “High” mode for a few
minutes, do not press the
push button to keep the
flashlight working on the
“High” mode repeatedly.
NOTE: Due to the high power of this LED flashlight, the product will
generate heat when working on the “High” mode. It’s specifically
engineering designed, used in ambient environment normally
won’t generate too much heat and the LED flashlight surface
temperature is still in an acceptable range to human hands.

CARE & CLEANING
CAUTION: Before attempting to clean the flashlight, turn off the power
of the LED flashlight by pressing the push button.
Your LED flashlight is made from quality materials that will last many
years with minimum care. You may want to periodically clean the lens,
or interior of the LED flashlight using a mild, non-abrasive glass
cleaner and a soft cloth.
DO NOT use solvents, or cleaners containing abrasive agents. When
cleaning the inside of the LED flashlight, make sure you have the
power turned off, and do not spray liquid cleaner directly onto the
LED, Printed Circuit Boards or wiring.
Lubricate all threads and rubber O-rings with petroleum jelly twice
yearly. Inspect flashlight monthly and carefully remove any damaged
batteries and clean any corrosion.